Performance Tool W1612 2.5 Ton Hydraulic Floor Jack User Manual

1. Alaye Aabo

Always prioritize safety when operating the Performance Tool W1612 hydraulic floor jack. Failure to follow these instructions may result in serious injury or property damage.

• Ka iwe afọwọkọ naa: Read and understand all instructions and warnings in this manual before using this product.
• Use on Hard, Level Surface: Operate the jack only on a hard, level surface capable of supporting the load. Avoid uneven or soft ground.
• Do Not Exceed Capacity: Never exceed the rated capacity of 5,000 lbs (2.5 tons).
• Lo Jack Iduro: After lifting the vehicle to the desired height, always support it immediately with appropriately rated jack stands. The hydraulic jack is a lifting device only and is not designed to sustain loads for extended periods.
• Ṣe aarin ẹrù naa: Ensure the load is centered on the jack saddle. Off-center loads can cause instability.
• Wọ Ohun elo Aabo: Always wear ANSI-approved safety goggles and heavy-duty work gloves during operation.
• Jeki Kedere: Keep hands, feet, and other body parts clear of moving parts and the vehicle during lifting and lowering.
• Ṣayẹwo Ṣaaju Lilo: Before each use, inspect the jack for any damage, leaks, or loose parts. Do not use if damaged.
• Ibi ipamọ to tọ: Store the jack in a clean, dry place, fully lowered, when not in use.

2. Ọja Ipariview

The Performance Tool W1612 is a heavy-duty 2.5 ton (5,000 lb) hydraulic floor jack designed for lifting vehicles. It features a robust steel construction, wide front wheels, and a 360-degree swivel saddle for ease of use.

Awọn eroja pataki:

• Apa gbigbe: The main arm that raises and lowers the vehicle.
• Gàárì, The contact point with the vehicle's lifting area.
• Mu: Used for pumping to lift and rotating to lower.
• Tu silẹ Valve: Controls the lowering speed of the jack.
• Àwọn kẹ̀kẹ́/Àwọn ohun èlò ìkọ́lé: Allow for easy positioning and maneuvering.

Figure 1: Performance Tool W1612 2.5 Ton Hydraulic Floor Jack. This image shows the overall design of the yellow hydraulic floor jack with its long handle and wheels.

olusin 2: Apa view of the Performance Tool W1612 Hydraulic Floor Jack. This image provides a different angle of the jack, highlighting its low-profile design and robust construction.

3. Eto

Igbaradi Ibere:

1. Ṣii silẹ: Fi ìṣọ́ra yọ àpò ìkọ̀kọ̀ náà kúrò nínú àpótí rẹ̀. Ṣe àyẹ̀wò bóyá ìbàjẹ́ bá ṣẹlẹ̀ sí ọkọ̀ ojú omi náà.
2. Mu Apejọ: Insert the handle into the handle socket and secure it according to the instructions provided in the packaging.

Bleeding the Hydraulic System:

Air can become trapped in the hydraulic system during shipping or use, affecting performance. Bleeding the system removes this air.

1. Fáfà Ìtúsílẹ̀ Ṣíṣí: Turn the handle counter-clockwise to fully open the release valve.
2. Imudani fifa fifa: Pump the handle 6-8 full strokes to force air out of the system.
3. Pade Tu silẹ Àtọwọdá: Yipada mimu si ọna aago lati pa àtọwọdá itusilẹ.
4. Idanwo: Test the jack by lifting and lowering it a few times without a load. If the jack does not lift smoothly or to its full height, repeat the bleeding process.

4. Awọn ilana Iṣiṣẹ

Gbigbe ọkọ ayọkẹlẹ kan:

1. Mura Ọkọ: Dá ọkọ̀ náà sí orí ilẹ̀ líle tí ó tẹ́jú. Fi bírékì ìdúró ọkọ̀ náà sí i kí o sì dí àwọn kẹ̀kẹ́ tí yóò wà nílẹ̀.
2. Ipo Jack: Position the jack directly under the vehicle's designated lifting point. Consult your vehicle's owner's manual for proper lifting points.
3. Pade Tu silẹ Àtọwọdá: Turn the handle clockwise until the release valve is firmly closed. Do not overtighten.
4. Ọkọ̀ agbéga: Pump the handle up and down to raise the vehicle to the desired height. Ensure the vehicle remains stable during lifting.
5. Ni aabo pẹlu Jack Stands: Once the vehicle is at the desired height, immediately place appropriately rated jack stands under the vehicle's frame or designated support points.
6. Slightly Lower onto Stands: Slowly turn the handle counter-clockwise to open the release valve, allowing the vehicle to gently rest onto the jack stands. Remove the hydraulic jack once the vehicle is securely supported by the stands.

Sisọ ọkọ silẹ:

1. Reposition Jack: If removed, place the hydraulic jack back under the vehicle's lifting point and raise it slightly to take the load off the jack stands.
2. Yọ Awọn iduro Jack kuro: Fara balẹ̀ yọ àwọn ibi ìdúró ọkọ̀ kúrò lábẹ́ ọkọ̀ náà.
3. Ọkọ kekere: Slowly turn the handle counter-clockwise to open the release valve. Control the lowering speed by adjusting how much you open the valve.
4. Fully Lower: Once the vehicle is fully lowered, remove the jack.

5. Itọju

Regular maintenance ensures the longevity and safe operation of your hydraulic floor jack.

• Ipele Omi Hydraulic: Check the hydraulic fluid level periodically. With the jack fully lowered, remove the oil filler plug. The fluid level should be just below the filler hole. Top up with high-quality hydraulic jack oil if necessary. Do not use brake fluid or motor oil.
• Lubrication: Lubricate all moving parts and pivot points with light machine oil monthly or as needed.
• Ninu: Keep the jack clean and free of dirt, grease, and corrosive materials. Wipe down the ram and pump plungers after each use.
• Ibi ipamọ: Store the jack in a dry, protected area, fully lowered, to prevent rust and seal damage.

6. Laasigbotitusita

7. Awọn pato

• Awoṣe: W1612
• Agbara fifuye: 5,000 lbs (2.5 Toonu)
• Giga Igbega ti o pọju: 19.25 inches
• Minimum Lifting Height: Approximately 5 inches (standard floor jack minimums)
• Ohun elo: Alloy Irin
• Ìwọ̀n Nkan: 79.7 iwon
• Awọn iwọn Ọja (L x W x H): 30.6 x 8.6 x 15.4 inches
• Irú Iṣẹ́ Ọkọ́: Ọkọ ayọkẹlẹ, Ọkọ ayọkẹlẹ

8. Atilẹyin ọja ati Support

For warranty information or technical support regarding your Performance Tool W1612 hydraulic floor jack, please refer to the documentation included with your purchase or contact Performance Tool customer service directly. Keep your purchase receipt for warranty claims.

Olupese: Performance Tool (Wilmar Corporation)

UPC: 039564124778

Ọjọ Akọkọ Wa: Oṣu Kẹrin Ọjọ 1, Ọdun 2004