1. Ifihan
Awọn Amprobe LAN-1 LAN Cable Tester is a diagnostic tool designed to identify and trace data cables and connectors. It helps detect common wiring issues such as shorts, miswirings, and open circuits in various cable types. This manual provides detailed instructions for the proper use, setup, and maintenance of your LAN-1 tester.
The LAN-1 evaluates most common cable types, including 10/100 base-T, 10 base-2, RJ45 modular, AT&T 258A, EIA/TIA 568A/568B, and Token Ring cables, as well as RJ45 and BNC connectors. It can test cables up to 300 meters long and uses LED indicators and an audible buzzer to signal cable status and errors.
2. Alaye Aabo
Jọwọ ka ki o si ye gbogbo awọn itọnisọna aabo ṣaaju lilo Amprobe LAN-1 LAN Cable Tester. Failure to follow these instructions may result in injury or damage to the device.
- Má ṣe lo ẹ̀rọ náà tí ó bá dà bíi pé ó ti bàjẹ́ tàbí tí kò bá ṣiṣẹ́ dáadáa.
- Ensure the correct battery type and polarity are used during installation.
- Yago fun ṣiṣafihan ẹrọ naa si awọn iwọn otutu to gaju, ọrinrin, tabi oorun taara.
- Ma ṣe gbiyanju lati tun tabi yi ẹrọ naa pada funrararẹ. Tọkasi gbogbo iṣẹ si oṣiṣẹ oṣiṣẹ.
- Always disconnect the cable tester from any active network or power source before performing maintenance or battery replacement.
3. Package Awọn akoonu
Daju pe gbogbo awọn nkan ti a ṣe akojọ rẹ si isalẹ wa ninu package rẹ:
- LAN-1 LAN Cable Tester
- (1) Remote terminator
- (1) RJ45 to female BNC cable
- (1) RJ45 to male BNC cable
- (1) RJ45 to RJ45 cable
- (1) Female BNC to female BNC cable
- (1) 9V battery (installed)
- Àwọn ìlànà (ìtọ́sọ́nà yìí)
4. Ọja Ipariview
Awọn Amprobe LAN-1 features a compact design with intuitive controls and clear LED indicators for efficient cable testing.
4.1 Key Awọn ẹya ara ẹrọ
- Cable Testing: Locates and traces data cables and connectors to identify shorts, miswiring, and opens.
- Ibamu Wapọ: Evaluates 10/100 base-T, 10 base-2, RJ45 modular, AT&T 258A, EIA/TIA 568A/568B, and Token Ring cables, along with RJ45 and BNC connectors.
- Itọkasi aṣiṣe: An audible buzzer indicates an error condition in the cable.
- Ibi ti o gbooro sii: Tests cables up to 300 meters long.
- Ko Ifihan kuro: Eighteen red and green LEDs indicate the source or test results.
- Awọn ọna Idanwo: Supports Loopback Test and Remote Test functions.
- Ibamu Aabo: CE - EMC certified.
4.2 Idanimọ paati
Nọmba 1: Iwaju view ti awọn Amprobe LAN-1 LAN Cable Tester. This image displays the main unit with its LED pin-out indicator, battery status light, and control buttons including AUTO, MAN, HOLD, TEST, BATT, and the power button.
Nọmba 2: Amprobe LAN-1 LAN Cable Tester showing the main unit and the remote terminator module. This view highlights how the remote unit connects to the main tester for comprehensive cable testing.
- PIN-OUT INDICATOR LEDs: Displays the wiring status for each pin (1-8) and ground (G).
- LED BAT: Tọkasi ipo batiri.
- Bọtini AUTO: Initiates automatic scanning of cable pins.
- MAN Button: Allows manual step-through of cable pins.
- Bọtini Dimu: Pauses the current test result display.
- Bọtini idanwo: Starts a test cycle.
- POWER Button (Yellow): Tan ẹrọ naa tan ati pa.
- Ibudo RJ45: For connecting RJ45 cables.
- BNC Port: For connecting BNC cables.
- Remote Terminator: A separate module used for testing installed cables or long runs.
5. Eto
5.1 Fifi sori batiri
The LAN-1 tester is powered by one 9V battery, which is typically pre-installed. If replacement is needed:
- Rii daju pe ẹrọ ti wa ni pipa.
- Locate the battery compartment cover on the back of the main unit.
- Remove the screw(s) securing the cover and carefully open it.
- Remove the old 9V battery and disconnect it from the terminals.
- Connect a new 9V battery, ensuring correct polarity (+ to + and - to -).
- Fi batiri sinu yara naa ki o si fi ideri naa pada, ki o si fi skru(s) so o mọ.
The battery provides power for up to 20 hours of testing.
5.2 Connecting Cables for Testing
Before testing, ensure the cable is disconnected from any active network equipment.
- For patch cables (short cables not installed in walls): Connect one end of the cable to the RJ45 or BNC port on the main unit and the other end to the corresponding port on the remote terminator.
- For installed cables (e.g., wall plates, patch panels): Connect one end of the cable to the RJ45 or BNC port on the main unit. Connect the remote terminator to the other end of the installed cable (e.g., at the wall plate in another room).
6. Awọn ilana Iṣiṣẹ
6.1 Titan / Pa a
Tẹ ofeefee AGBARA button to turn the device on. Press it again to turn the device off.
6.2 Ṣiṣe idanwo kan
Once the cable is connected, you can perform a test:
- Tẹ awọn Idanwo button to initiate a cable test.
- Automatic Scan (AUTO mode): Tẹ awọn AUTO button. The tester will automatically scan through each pin (1-8 and G) and display the results sequentially. This is suitable for quick checks.
- Manual Scan (MAN mode): Tẹ awọn OKUNRIN bọtini. Kọọkan titẹ ti awọn OKUNRIN button will advance the test to the next pin, allowing for a detailed examination of each connection.
- Iṣe idaduro: Tẹ awọn DIMU button to pause the current display of the pin-out indicator. Press it again to resume scanning.
6.3 Interpreting LED Indicators
The 18 red and green LEDs on the PIN-OUT INDICATOR provide visual feedback on the cable's status:
- Green Green: Indicates a correct connection for the corresponding pin.
- LED pupa: Indicates an error for the corresponding pin (e.g., open circuit, short circuit, miswiring).
- Ko si LED: May indicate an open circuit or a broken wire for that pin.
- Buzzer: An audible buzzer will sound when an error condition is detected, providing an additional alert.
The LEDs on the remote module will mirror the main unit's display for the corresponding pins, allowing for verification of end-to-end continuity.
6.4 Ṣayẹwo ipo batiri
Tẹ awọn BATT button to check the battery level. The BATT LED will illuminate if the battery has sufficient power. If the BATT LED does not light up or is dim, replace the 9V battery.
7. Itọju
7.1 Ninu
To ensure the longevity and proper functioning of your LAN-1 tester, keep it clean and free from dust and debris.
- Mu ese ita ti ẹrọ naa pẹlu asọ, damp asọ. Ma ṣe lo abrasive ose tabi epo.
- Ensure no moisture enters the ports or battery compartment.
7.2 Batiri Rirọpo
Replace the 9V battery when the BATT LED indicates low power or if the device fails to power on. Refer to Section 5.1 for detailed battery installation instructions.
Nigbagbogbo sọ awọn batiri ti a lo ni ibamu si awọn ilana agbegbe.
8. Laasigbotitusita
Ti o ba pade awọn iṣoro rẹ Amprobe LAN-1 LAN Cable Tester, refer to the following common problems and solutions:
| Isoro | Owun to le Fa | Ojutu |
|---|---|---|
| Ẹrọ naa ko ṣiṣẹ. | Kekere tabi okú batiri; fifi sori batiri ti ko tọ. | Rọpo batiri 9V, ki o rii daju pe o pe polarity. |
| No LED activity during test. | Cable not properly connected; faulty cable; remote terminator not connected. | Ensure cables are securely connected to both the main unit and remote terminator. Test with a known good cable. |
| Buzzer sounds continuously or unexpectedly. | Short circuit or severe miswiring detected. | Examine the cable for physical damage or incorrect wiring. Check connectors for bent pins. |
| Awọn abajade idanwo ti ko ni ibamu. | Loose connections; intermittent cable fault; low battery. | Ensure all connections are tight. Replace battery. Try wiggling the cable during test to identify intermittent faults. |
9. Awọn pato
| Awoṣe | LAN-1 |
| Ibi ti ina elekitiriki ti nwa | (1) 9V battery |
| Igbesi aye batiri | Up to 20 hours of tests |
| Cable Types Tested | 10/100 base-T, 10 base-2, RJ45 modular, AT&T 258A, EIA/TIA 568A/568B, Token Ring cables |
| Cable Connector Types | RJ45 and BNC |
| Maximum Line Length | 300m |
| Iwọn | 0.6 lb. / 0.27 kg (approx. 9.5 ounces) |
| Awọn iwọn (H x W x D) | 5.1 x 2.2 x 1.5 in. / 130 x 56 x 38mm |
| Ifihan | 18 LEDs (9 Red and 9 Green), 9 LEDs on Remote module |
| Ibamu Aabo | CE - EMC |
10. atilẹyin ọja Information
Awọn Amprobe LAN-1 LAN Cable Tester comes with a Atilẹyin ọja Odun kan. This warranty covers defects in materials and workmanship under normal use. It does not cover damage resulting from misuse, accident, modification, neglect, or unauthorized repair.
For specific warranty terms and conditions, please refer to the warranty card included with your product or contact Amprobe customer support.
11. Onibara Support
If you have any questions, require technical assistance, or need to report a problem with your Amprobe LAN-1 LAN Cable Tester, please contact Amprobe customer support.
Jọwọ ṣabẹwo si osise naa Ampaso webaaye fun alaye olubasọrọ ti o ni imudojuiwọn julọ ati awọn orisun atilẹyin.
Awọn orisun Ayelujara: www.amprobe.com