Actiontec My Wireless TV WiFi / HDMI Multi-Room Wireless HD Video Kit (MWTV200KIT-01) User Manual

1. Ifihan

The Actiontec My Wireless TV WiFi / HDMI Multi-Room Wireless HD Video Kit (MWTV200KIT-01) provides a solution for wirelessly distributing high-definition video and audio throughout your home. This kit allows you to transmit full 1080p HD and 3D video from an HDMI source device to an HDTV or projector up to 150 feet away, without the need for long HDMI cables. It supports HDCP 2.0 for protected content and includes IR back-channel functionality for controlling your source device remotely.

This manual provides detailed instructions for setting up, operating, and maintaining your My Wireless TV kit, along with troubleshooting tips and product specifications.

2. Ohun ti o wa ninu Apoti

Verify that all components are present in your My Wireless TV kit:

• Wireless HD Video Transmitter
• Wireless HD Video Receiver
• Energy efficient power supplies (x2)
• High-speed HDMI cables (x2)
• IR Blaster USB
• USB olugba IR
• Isakoṣo latọna jijin
• Itọsọna ibere ni kiakia

3. Awọn ilana iṣeto

Follow these steps to set up your Actiontec My Wireless TV kit:

3.1. Connect the Transmitter

1. Power Off Source Device: Ensure your HDMI source device (e.g., cable box, Blu-ray player) is powered off.
2. So HDMI pọ: Connect one end of an HDMI cable to the HDMI output port of your source device. Connect the other end of the HDMI cable to the HDMI-IN port on the My Wireless TV Transmitter.
3. So agbara: Connect one of the energy-efficient power supplies to the Transmitter's power port and plug it into an electrical outlet.
4. (Optional) HDMI Pass-through: If you wish to connect a local TV to the same source, connect another HDMI cable from the HDMI Jade (pass-through) port on the Transmitter to your local TV's HDMI input.
5. (Optional) IR Blaster: If you intend to control your source device remotely, plug the IR Blaster cable into the IR Jade port on the Transmitter. Position the IR Blaster emitter directly over the IR sensor of your source device.

Aworan: Ẹyin view of the Actiontec My Wireless TV Transmitter, showing HDMI In, HDMI Out, IR Out, and power ports.

3.2. So Olugba

1. Power Off Display: Ensure your HDTV or projector is powered off.
2. So HDMI pọ: Connect the second HDMI cable from the HDMI Jade port on the My Wireless TV Receiver to an available HDMI input port on your HDTV or projector.
3. So agbara: Connect the second energy-efficient power supply to the Receiver's power port and plug it into an electrical outlet.
4. (Optional) IR Receiver: If you intend to control your source device remotely, plug the IR Receiver cable into the IR IN port on the Receiver. Position the IR Receiver sensor in a location where it can receive signals from your remote control.

Aworan: Ẹyin view of the Actiontec My Wireless TV Receiver, showing HDMI Out, IR In, and power ports.

3.3. Power On and Sync

1. Agbara Lori Awọn ẹrọ: Power on your source device, the My Wireless TV Transmitter, the My Wireless TV Receiver, and your HDTV/projector.
2. Yan Igbewọle: On your HDTV/projector, select the HDMI input connected to the My Wireless TV Receiver.
3. Amuṣiṣẹpọ aladaaṣe: The Transmitter and Receiver should automatically establish a wireless connection. The "Wireless" LED indicator on both units will illuminate when a connection is established.
4. Manual Sync (if needed): If the units do not sync automatically, press the "Sync" button on both the Transmitter and Receiver simultaneously for a few seconds until the "Wireless" LED blinks, then becomes solid.
5. Gbadun: Once synced, the video from your source device should appear on your remote display.

4. Isẹ

4.1. Viewing Akoonu

After successful setup and syncing, the content from your HDMI source device will be wirelessly transmitted to the connected HDTV or projector. Ensure the remote display is set to the correct HDMI input.

4.2. Remote Control Functionality (IR Back-channel)

The included IR Blaster and IR Receiver cables enable you to control your source device from the remote display location. Point your source device's original remote control at the My Wireless TV Receiver's IR sensor. The signal will be transmitted back to the Transmitter, which then uses the IR Blaster to control your source device.

4.3. Iṣakoso loju iboju

The My Wireless TV kit features an on-screen control interface. Use the provided remote control to navigate this interface for source switching and accessing advanced features. Refer to the quick start guide for specific remote control button functions.

5. Itọju

• Ninu: Use a soft, dry cloth to clean the surfaces of the Transmitter and Receiver. Do not use liquid cleaners or aerosols.
• Afẹfẹ: Ensure that the units have adequate ventilation. Do not block ventilation openings.
• Awọn imudojuiwọn famuwia: Periodically check the Actiontec support webAaye fun awọn imudojuiwọn famuwia lati rii daju pe iṣẹ ṣiṣe to dara julọ ati ibamu.
• Yiyipo Agbara: If experiencing minor issues, power cycling both the Transmitter and Receiver (unplugging and replugging after 10 seconds) can often resolve them.

6. Laasigbotitusita

This section addresses common issues you might encounter with your My Wireless TV kit.

6.1. No Picture or Signal

• Ṣayẹwo Awọn isopọ: Ensure all HDMI and power cables are securely connected to both the Transmitter and Receiver, and to your source and display devices.
• Correct Input: Verify that your HDTV or projector is set to the correct HDMI input.
• Ipo Agbara: Confirm that both the Transmitter and Receiver are powered on (power LEDs illuminated).
• Amuṣiṣẹpọ Alailowaya: Check the "Wireless" LED on both units. If it's not solid, try pressing the "Sync" button on both units simultaneously.
• Ẹrọ Orisun: Ensure your source device is powered on and outputting a signal.
• Ìjánu: Wireless transmission can be affected by obstacles (walls, furniture) and other wireless devices (Wi-Fi routers, cordless phones). Try repositioning the units or reducing the distance between them.

6.2. Picture Flickering or Intermittent Signal

• Ijinna ati Idiwo: The wireless signal strength decreases with distance and when passing through multiple walls or dense materials. Try moving the Receiver closer to the Transmitter or ensuring a clearer line of sight.
• Ìjánu: Other wireless devices operating on similar frequencies (2.4GHz or 5GHz) can cause interference. Try changing the wireless channel if your units support this feature (check on-screen menu or support documentation).
• Yiyipo Agbara: Perform a power cycle on both the Transmitter and Receiver.

6.3. Isakoṣo latọna jijin Ko Ṣiṣẹ

• IR Cable Placement: Ensure the IR Blaster emitter is directly over the IR sensor of your source device. The IR Receiver should be positioned to receive signals from your remote.
• Laini Oju: Ensure there is a clear line of sight between your remote control and the IR Receiver.
• Awọn batiri: Check the batteries in your source device's remote control.

6.4. Audio Issues (No Sound or Distorted Audio)

• Awọn asopọ HDMI: Re-check all HDMI cable connections.
• Fi Àwọn Ètò Ohùn Hàn: Verify the audio settings on your HDTV or projector.
• Ètò Ohùn Orísun: Ensure your source device is outputting audio correctly.

7. Awọn pato

8. Atilẹyin ọja ati Support

For technical assistance, warranty information, or to download the latest software and firmware updates, please visit the official Actiontec support webojula:

www.actiontec.com/support

Please have your product model number (MWTV200KIT-01) and serial number ready when contacting support.