1. Ifihan
This manual provides instructions for the installation, operation, and maintenance of your Lepro 12V LED Strip Light. This flexible, non-waterproof LED tape light is designed for indoor decorative and accent lighting applications. Please read this manual thoroughly before installation and use.
2. Alaye Aabo
- Adapter agbara: A 12V DC power adapter is ko si and must be purchased separately. Ensure the power adapter's output voltage is exactly 12V. Using a higher voltage adapter will damage the LED strip.
- Wattage: Lapapọ wattage of the LED strip (18W for 16.4ft) must not exceed the maximum wattage rating of your power adapter.
- Ooru: The LED strip operates at an extremely low heat, making it safe to touch.
- Omi Resistance: Ọja yii jẹ ti kii-mabomire and intended for indoor use only. Avoid exposure to water or high humidity.
- Mimu: The LED strip is flexible but fragile. Handle with care during installation to prevent tearing or damage to the PCB.
- Ige: Only cut the LED strip at designated cutting marks (every 3 LEDs) to avoid damaging the circuit.
3. Package Awọn akoonu
Jẹrisi pe gbogbo awọn paati wa ninu package rẹ:
- 1 x Lepro 12V LED Strip Light (16.4 ft)
- Accessories (e.g., connectors, clips - specific accessories may vary, power adapter not included)
Figure 3.1: Package Contents. Note: 12V power supply sold separately.
4. Awọn pato
| Ẹya ara ẹrọ | Ẹ̀kúnrẹ́rẹ́ |
|---|---|
| Nọmba awoṣe | Ọdun 4100057-WW |
| Imọlẹ Iru | LED Strip Light (SMD 2835) |
| Gigun | 16.4 ft (mita 5) |
| Awọ Imọlẹ | Alawọ gbona |
| Iwọn otutu awọ | 3000 Kelvin |
| Voltage | DC 12V |
| Wattage | 18 Wattis |
| Flux Imọlẹ | 1200 Lumens |
| Nọmba ti LED | 300 |
| Dimmable | No (Not Dimmable) |
| inu ile / ita gbangba Lo | Ninu ile Nikan |
| Ohun elo | Silikoni |
| Iwọn Nkan | 60 Giramu (2.12 iwon) |
Lilo Agbara
Figure 4.1: Energy Efficiency Label. For more details, visit eprel.ec.europa.eu/qr/1056793.
5. Awọn ilana iṣeto
5.1 irinše Loriview
Figure 5.1: LED Strip Light Components. A 12V power supply is required and sold separately.
5.2 fifi sori Igbesẹ
- Ṣetan Ilẹ: Ensure the surface where the LED strip will be applied is clean, dry, and smooth. Wipe the surface with a clean cloth to remove any dust or debris.
- Wọ́n àti Gé (Àṣàyàn): If a shorter length is desired, measure the required length. The LED strip can be cut every 3 LEDs along the designated cutting marks. Use sharp scissors for a clean cut. Note: 2-pin 8mm connectors are not included if you cut the strip.
- Lo ìlà náà: Peel off the protective backing from the self-adhesive tape on the back of the LED strip. Carefully press the strip onto the prepared surface, ensuring firm contact along its entire length.
- So agbara: Connect the LED strip to a compatible 12V DC power adapter (not included). Ensure the polarity is correct.
Figure 5.2: Installation Process: Clean surface, peel adhesive, and cut at marks.
6. Awọn ilana Iṣiṣẹ
Once properly installed and connected to a 12V DC power adapter, the LED strip light will illuminate when the power adapter is plugged into an electrical outlet. This model is ko dimmable and does not include a controller. To turn the lights on or off, you must control the power supply directly (e.g., by plugging/unplugging or using a switched outlet).
6.1 Product in Use
Olusin 6.1: Example of Warm White LED Strip Light application in a living space.
Figure 6.2: Warm White 3000K LED lighting in a home environment.
6.2 Video ifihan
Video 6.1: Warm White LED Lights Strip for Bedroom. This video demonstrates the appearance of the warm white LED strip lights in a bedroom setting.
7. Itọju
- Ninu: To clean the LED strip, ensure it is unplugged from the power source. Gently wipe the surface with a soft, dry cloth. Do not use abrasive cleaners or immerse the strip in water.
- Mimu: Avoid bending the strip sharply or applying excessive force, as this can damage the internal circuitry.
- Ibi ipamọ: If storing the LED strip, roll it loosely on its original reel or a similar circular object to prevent kinks or damage.
8. Laasigbotitusita
| Isoro | Owun to le Fa | Ojutu |
|---|---|---|
| LED rinhoho ko ni tan imọlẹ. | Kò sí agbára, ìpele tí kò tọ́tage, faulty power adapter, or damaged strip. | Ensure the 12V power adapter is correctly plugged in and functioning. Verify the power adapter output is 12V DC. Check for visible damage to the strip or connections. |
| Portions of the strip are not lighting up. | Damage to a section of the strip, incorrect cutting, or faulty connection. | Inspect the unlit section for physical damage or improper cuts. Ensure any connectors used are secure. |
| Lẹ́mọ́ra kò jẹ́ kí ó di ìlà náà mú. | Surface was not clean or smooth, or adhesive has lost its stickiness. | Clean the surface thoroughly before application. For persistent issues, consider using additional adhesive clips or a stronger double-sided tape (e.g., hot glue as a temporary solution, as mentioned in customer reviews, but be aware of potential damage upon removal). |
9. Atilẹyin ọja & Atilẹyin
9.1 atilẹyin ọja Alaye
This Lepro LED Strip Light comes with a 2-odun atilẹyin ọja from the date of purchase. This warranty covers manufacturing defects under normal use. It does not cover damage caused by improper installation, misuse, accidents, or unauthorized modifications.
9.2 Onibara Support
For technical assistance, warranty claims, or any questions regarding your Lepro product, please contact Lepro customer support through the retailer's platform or visit the official Lepro webojula fun alaye olubasọrọ.