Napoleon F60 Fireplace Remote Control User Manual

1. Ifihan

The Napoleon F60 Fireplace Remote Control provides convenient and effective control over your Napoleon heating appliance. This battery-operated, hand-held device features a clear digital screen for easy temperature monitoring and adjustment. It is designed to simplify the operation of your fireplace, allowing for precise temperature management and on/off control.

Awọn ẹya pataki pẹlu:

• Convenient on/off and thermostat control.
• Battery-operated, hand-held design with an easy-to-read digital screen.
• A 2-degree temperature swing to reduce short on/off cycling (e.g., if set to 70°F, the fireplace activates at 69°F and deactivates at 71°F).
• Ability to monitor room temperature every 60 seconds and adjust accordingly.

2. Ohun ti o wa ninu Apoti

Upon unpacking your Napoleon F60 Fireplace Remote Control, ensure all the following components are present:

• Transmitter (Remote Control Unit)
• Olugba Unit
• Wall Mount Jojolo
• Wall Faceplate
• Fireplace Mounting Plate
• Yipada
• 2 AAA Batteries (for Transmitter)
• 4 AA Batteries (for Receiver)
• Afowoyi Olumulo (iwe-ipamọ yii)

Image: The Napoleon F60 Fireplace Remote Control (transmitter) and its associated receiver unit.

3. Eto ati fifi sori

This section guides you through the physical installation and initial setup of your Napoleon F60 remote control system. Please refer to your fireplace's manual for specific details regarding its millivolt valve connections.

3.1. Connecting the Receiver to the Fireplace

1. Identify Fireplace Connections: Locate the existing wall switch wires connected to your fireplace's millivolt gas valve. These are typically labeled TH/TP terminals.
2. Disconnect Wall Switch: Carefully unplug the wires from your existing wall switch.
3. Àwọn wáyà Olùgbà Sopọ̀: Connect the two wires from the F60 receiver unit to the TH/TP terminals on your fireplace's millivolt gas valve. Ensure a secure connection. The F60 receiver effectively replaces your manual wall switch.
4. Fi Awọn batiri sii: Insert the provided 4 AA batteries into the receiver unit and 2 AAA batteries into the transmitter (remote control).

3.2. Ibẹrẹ Ibẹrẹ

If your remote and receiver are not pre-paired, or if you need to re-pair them:

1. Ensure the receiver unit is powered on.
2. Locate the reset button on the receiver unit.
3. Press and hold the reset button for approximately 5 seconds until an indicator light on the receiver begins to blink.
4. Tu bọtini naa silẹ.
5. Within a few seconds, press a button on the remote control (transmitter). The indicator light on the receiver should stop blinking and remain solid, indicating successful pairing.

4. Awọn ilana Iṣiṣẹ

The Napoleon F60 remote control offers simple and intuitive operation for your fireplace.

4.1. Tan / Pa Iṣakoso

• Tẹ awọn Agbara button (Power icon) once to turn the fireplace ON.
• Tẹ awọn Agbara button again to turn the fireplace OFF.

4.2. Iṣakoso Itọju Ẹrọ

The remote allows you to set a desired room temperature. The fireplace will automatically turn on or off to maintain this temperature.

• Tẹ awọn Iwọn otutu button (Thermometer icon) to activate thermostat mode.
• Lo awọn Up (Up arrow icon) and Isalẹ (Down arrow icon) arrow buttons to adjust the desired temperature.
• The digital screen will display the current room temperature and your set temperature.
• The system is designed with a 2-degree temperature swing. For example, if the thermostat is set to 70°F, the fireplace will activate when the room temperature drops to 69°F and turn off when it reaches 71°F.

5. Itọju

To ensure optimal performance and longevity of your Napoleon F60 Fireplace Remote Control:

• Rirọpo Batiri: Replace the batteries in both the transmitter (2 AAA) and receiver (4 AA) when the display becomes dim or the remote's response is sluggish. Always use fresh, high-quality batteries.
• Ninu: Fi aṣọ rírọrùn àti gbígbẹ nu iṣakoso latọna jijin ati olugba naa. Maṣe lo awọn ohun elo fifọ tabi fi omi rì.
• Ibi: Ensure the receiver unit is placed in an area that allows for good signal reception and is not directly exposed to excessive heat or moisture. The metal enclosure of the receiver is designed to withstand heat, but extreme conditions should be avoided.
• Eriali: Ensure the external antenna on the receiver is positioned for optimal signal transmission, especially if the receiver is located within a metal fireplace enclosure.

6. Laasigbotitusita

If you encounter issues with your Napoleon F60 remote control, try the following solutions:

• Latọna jijin Ko Dahun:
  • Check and replace batteries in both the transmitter and receiver.
  • Ensure the remote and receiver are within operational range and there are no obstructions.
  • Re-pair the remote and receiver (refer to Section 3.2).
• Fireplace Not Turning On/Off:
  • Verify that the fireplace's pilot light is lit.
  • Check the wiring connections between the receiver and the fireplace's millivolt valve.
  • Ensure the receiver is powered on and its indicator light is functioning correctly.
• Awọn kika iwọn otutu ti ko tọ:
  • Ensure the remote control is not placed near a direct heat source or in direct sunlight, which can affect its internal thermometer.
  • Allow sufficient time for the remote to acclimate to the room temperature.
• Ifiranṣẹ Alailowaya:
  • Adjust the position of the receiver's external antenna for better signal reception.
  • Ensure the receiver is not completely enclosed by metal, which can interfere with wireless signals.

Ti awọn iṣoro ba tẹsiwaju lẹhin igbiyanju awọn igbesẹ wọnyi, jọwọ kan si atilẹyin alabara.

7. Awọn pato

8. Atilẹyin ọja ati Support

For warranty information, technical support, or service inquiries, please refer to the official Napoleon product webojula tabi kan si wọn onibara iṣẹ Eka. Tọju iwe-ẹri rira rẹ bi ẹri rira fun eyikeyi awọn ibeere atilẹyin ọja.