1. Ifihan
This manual provides detailed instructions for the installation, operation, and maintenance of your Claber 90814 24V Solenoid Valve. This robust and reliable solenoid valve is designed for underground irrigation systems, ensuring efficient water management. It is engineered to operate effectively across a wide range of water pressures, from minimal to high, and is compatible with all Claber 24V programmers.
Image 1: Claber 90814 24V Solenoid Valve. This image shows the compact design of the valve, highlighting its inlet and outlet connections and the solenoid component.
2. Alaye Aabo
- Always disconnect power to the irrigation controller before installing or servicing the solenoid valve.
- Ensure all electrical connections are waterproof and comply with local electrical codes.
- Do not exceed the maximum operating pressure of 12 bar (174 psi).
- Install the valve in a location protected from freezing temperatures.
- Use appropriate tools for installation to avoid damaging the valve or piping.
3. Package Awọn akoonu
Daju pe gbogbo awọn paati wa ṣaaju ki o to bẹrẹ fifi sori:
- 1 x Claber 90814 24V Solenoid Valve
4. Eto ati fifi sori
- Mura Ibi: Choose a suitable location for the valve, typically within a valve box, ensuring it is accessible for maintenance and protected from direct sunlight or extreme weather.
- Pípù ìsopọ̀: The valve features 1" female inlet and outlet threads. Apply PTFE tape or pipe sealant to the male threads of your irrigation pipes. Connect the inlet pipe to the side marked 'IN' or with an arrow indicating flow direction, and the outlet pipe to the other side. Hand-tighten, then use a wrench for a final quarter to half turn, avoiding over-tightening.
- Asopọmọra itanna: Connect the two wires from the solenoid to the corresponding 24V AC output terminals on your irrigation programmer. Ensure a secure, waterproof connection using appropriate connectors (e.g., waterproof wire nuts). This valve is compatible with any 24V AC multi-line programmer.
- Idanwo fun Leaks: Before burying the valve, slowly turn on the main water supply and check for any leaks at the connections.
- Manual Operation Check: The valve is equipped with a manual open/close device. Turn the manual override lever or screw to the 'OPEN' position to allow water flow, then return it to 'CLOSE' to stop flow. This confirms the valve's mechanical function.
5. Awọn ilana Iṣiṣẹ
The Claber 90814 solenoid valve operates automatically in conjunction with a 24V AC irrigation programmer.
- Isẹ aladaaṣe: Once connected to a compatible 24V AC programmer, the valve will open and close according to the schedule set on the programmer. When the programmer sends a 24V AC signal, the solenoid activates, opening the valve. When the signal is removed, the valve closes.
- Isẹ afọwọṣe: Ni ọran ti agbara otage or for testing purposes, you can manually open and close the valve using the integrated manual override mechanism. Locate the lever or screw on the solenoid and turn it to the 'OPEN' position for continuous water flow, or 'CLOSE' to stop the flow. Remember to return it to the 'AUTO' or 'CLOSED' position for automatic operation.
6. Itọju
- Solenoid Filter: The solenoid is equipped with an anti-sand filter. Periodically inspect and clean this filter to prevent blockages and ensure proper valve operation.
- Igba otutu: In regions prone to freezing temperatures, it is crucial to drain the irrigation system, including the solenoid valve, to prevent damage from freezing water. Consult your irrigation system's winterization guide.
- Ayẹwo gbogbogbo: Annually inspect the valve for any signs of wear, leaks, or damage. Ensure electrical connections remain secure and waterproof.
7. Laasigbotitusita
| Isoro | Owun to le Fa | Ojutu |
|---|---|---|
| Valve ko ṣii | No power to solenoid; faulty wiring; clogged filter; low water pressure. | Check programmer schedule and power supply; inspect wiring connections; clean solenoid filter; verify water pressure. |
| Àtọwọdá ko ni tilekun | Debris in valve; faulty solenoid; manual override engaged. | Flush the system to clear debris; inspect/replace solenoid; ensure manual override is in 'CLOSED' or 'AUTO' position. |
| Ṣiṣan omi kekere | Partially clogged filter; insufficient main water pressure. | Clean solenoid filter; check main water supply pressure. |
| Water leaks from valve | Loose connections; damaged O-rings/seals; cracked valve body. | Tighten connections; inspect and replace O-rings/seals; replace valve if body is cracked. |
8. Awọn pato
- Nọmba awoṣe: 90814
- Brand: Claber
- Iru Valve: Solenoid àtọwọdá
- Awọn ọna Voltage: 24V AC
- Inlet/Outlet Thread: 1" Female
- Agbara Iṣiṣẹ: 0.5 si 12 igi (7.25 si 174 psi)
- Oṣuwọn Sisan: 4.6 to 96 liters/minute
- Iwọn Iṣiṣẹ: +5°C si +70°C (41°F si 158°F)
- Ohun elo: Fiberglass-reinforced nylon body, Stainless steel metal components
- Awọn ẹya: Anti-sand filter, Slow closing anti-water hammer device, Manual open/close control
- Compliant Specifications: EN 1074-1, EN 1074-2, CE
- Awọn iwọn idii: 13.4 x 12.4 x 8.4 cm
- Ìwúwo: 360 giramu
9. Atilẹyin ọja ati Support
Claber products are manufactured to high-quality standards. For information regarding warranty coverage, technical support, or spare parts, please refer to the official Claber webojú òpó wẹ́ẹ̀bù tàbí kí o kàn sí oníṣòwò tí a fún ní àṣẹ ní agbègbè rẹ. Pa ìwé ẹ̀rí ìrajà rẹ mọ́ gẹ́gẹ́ bí ẹ̀rí ìrajà náà.