SMT Ultrasonic Homogenizer UH-50 Instruction Manual

1. Ifihan

This manual provides essential information for the safe and efficient operation of the SMT Ultrasonic Homogenizer UH-50. Please read this manual thoroughly before using the device and keep it for future reference.

The SMT Ultrasonic Homogenizer UH-50 is a compact and lightweight device designed for laboratory applications requiring ultrasonic homogenization. Its key features include a space-saving design, a lightweight vibrator (approximately 160g), and a hand pulser for convenient control of ultrasonic vibration. The system automatically adjusts output to maintain a constant amplitude, adapting to variations in sample load and pressure.

2. Alaye Aabo

WARNING: This is a professional-use product. It should only be operated by trained personnel in a laboratory setting.

• No Dry Operation: Do not operate the ultrasonic vibrator without it being immersed in a liquid sample. Dry operation can cause damage to the device.
• Rii daju pe ẹrọ naa ti gbe sori iduro, ipele ipele.
• Connect the device to a grounded power outlet with the specified voltage (AC100V, 50/60Hz).
• Avoid direct contact with the vibrating tip during operation.
• Do not disassemble or attempt to repair the unit yourself. Refer to qualified service personnel.
• Keep the unit away from flammable materials and excessive moisture.

3. Ọja irinše ati idari

The SMT Ultrasonic Homogenizer UH-50 consists of a main control unit and an ultrasonic vibrator with a hand pulser. Familiarize yourself with the components and controls shown below.

Figure 1: SMT Ultrasonic Homogenizer UH-50 Overview
This image displays the main control unit of the SMT Ultrasonic Homogenizer UH-50 on the left, connected to the ultrasonic vibrator on the right. The control unit features a "MONITOR" display, a "POWER" switch, "CONSTANT" and "HAND" mode selector, "TUNE" and "OUTPUT" adjustment knobs. A yellow label on top of the main unit warns against dry operation. The vibrator is a slender, metallic component with a tip.

Apejuwe Igbimọ Iṣakoso:

• AGBARA AGBARA: Yipada ẹyọ naa tan ati pa.
• MONITOR Display: Shows the current output level or other operational parameters.
• CONSTANT/HAND Selector:
  • IGBAGBỌ: Continuous ultrasonic operation.
  • ỌWỌ: Operation controlled by the hand pulser switch.
• TUNE Knob: Adjusts the ultrasonic frequency for optimal performance.
• Bọtini JADE: Controls the ultrasonic power output (amplitude).
• Hand Pulser: A switch located on the vibrator cable for convenient start/stop of ultrasonic vibration when in HAND mode.

4. Eto

1. Ṣii silẹ: Ni ifarabalẹ yọ gbogbo awọn paati kuro ninu apoti. Daju pe gbogbo awọn ẹya wa ni ibamu si atokọ iṣakojọpọ.
2. Ibi: Place the main control unit on a stable, flat, and dry surface, ensuring adequate ventilation around the unit.
3. Connect Vibrator: Connect the ultrasonic vibrator cable securely to the designated port on the main control unit.
4. Asopọ agbara: Ensure the POWER switch is in the "OFF" position. Connect the power cord to the main control unit and then to a grounded AC100V, 50/60Hz power outlet.
5. Ayẹwo akọkọ: Before first use, visually inspect the vibrator tip for any damage or wear.

5. Awọn ilana Iṣiṣẹ

Always ensure the vibrator tip is immersed in the sample liquid before starting operation to prevent damage from dry running.

1. Mura Sample: Gbe sample in an appropriate vessel. Ensure the vessel is suitable for ultrasonic treatment and can withstand the energy generated.
2. Immerse Vibrator: Carefully immerse the tip of the ultrasonic vibrator into the sample liquid. Ensure the tip is sufficiently submerged but not touching the bottom or sides of the vessel.
3. Agbara Tan: Turn the POWER switch to the "ON" position. The MONITOR display should illuminate.
4. Yan Ipo:
   • For continuous operation, set the selector to "CONSTANT".
   • For intermittent operation controlled by the hand pulser, set the selector to "HAND".
5. Adjust TUNE: Slowly adjust the TUNE knob until the MONITOR display shows the highest stable reading, indicating optimal resonance.
6. Set OUTPUT: Adjust the OUTPUT knob to the desired ultrasonic power level. The system will automatically control the output to maintain a constant amplitude.
7. Start Homogenization:
   • In "CONSTANT" mode, homogenization will start immediately.
   • In "HAND" mode, press and hold the switch on the hand pulser to start homogenization. Release the switch to stop.
8. Ilana Atẹle: Observe the homogenization process. Adjust OUTPUT or TUNE as necessary.
9. Ipari: Once homogenization is complete, turn the OUTPUT knob to minimum, then turn the POWER switch to "OFF".
10. Clean Vibrator: Carefully remove the vibrator from the sample and clean it immediately according to the maintenance instructions.

6. Itọju

Regular maintenance ensures the longevity and optimal performance of your SMT Ultrasonic Homogenizer UH-50.

• Cleaning the Vibrator Tip: After each use, thoroughly clean the vibrator tip to prevent sample residue buildup. Use appropriate cleaning agents for the materials being processed. Rinse with distilled water and dry completely.
• Ninu Ẹka Akọkọ: Wipe the exterior of the main control unit with a soft, damp cloth. Do not use abrasive cleaners or allow liquids to enter the unit.
• Ayewo: Periodically inspect the vibrator tip, cable, and connectors for any signs of wear, damage, or corrosion. Replace damaged parts immediately.
• Ibi ipamọ: Tọ́jú ẹ̀rọ náà sí ibi tí ó mọ́ tónítóní tí ó sì gbẹ nígbà tí a kò bá lò ó.

7. Laasigbotitusita

If you encounter issues with your SMT Ultrasonic Homogenizer UH-50, refer to the following common problems and solutions:

• Ko si Agbara:
  • Check if the power cord is securely connected to both the unit and the power outlet.
  • Rii daju pe iṣan agbara jẹ iṣẹ-ṣiṣe.
  • Verify the POWER switch is in the "ON" position.
• No Ultrasonic Vibration:
  • Ensure the vibrator tip is properly immersed in liquid.
  • Check the TUNE and OUTPUT knob settings. Adjust TUNE for optimal resonance.
  • If in "HAND" mode, ensure the hand pulser switch is pressed.
  • Inspect the vibrator cable for damage.
• Kekere tabi Ijade Aisedeede:
  • Adjust the TUNE knob to find the optimal frequency.
  • Increase the OUTPUT knob setting.
  • Ensure the vibrator tip is clean and free of damage.
  • Ṣe idaniloju awọn sample volume and viscosity are within appropriate limits for the device.

If the problem persists after attempting these solutions, please contact SMT customer support or your local distributor for assistance.

8. Awọn pato

9. Atilẹyin ọja ati Support

Specific warranty information for the SMT Ultrasonic Homogenizer UH-50 is not provided in this document. Please refer to your purchase agreement or contact your local SMT distributor for details regarding warranty coverage and technical support.

Fun iranlọwọ siwaju, o tun le ṣabẹwo si SMT Brand Store on Amazon.co.jp.