Ìwé Ìtọ́sọ́nà Olùlò Siglent Technologies SDS1052DL+ Oscilloscope àti SDG1032X Function Generator

1. Ifihan

This manual provides detailed instructions for the safe and effective operation of the Siglent Technologies SDS1052DL+ Digital Storage Oscilloscope and the SDG1032X Arbitrary Waveform Function Generator. Please read this manual thoroughly before using the instruments to ensure proper functionality and to prevent damage.

Figure 1: Siglent SDS1052DL+ Oscilloscope (left) and SDG1032X Function Generator (right)

This image displays the Siglent SDS1052DL+ Digital Storage Oscilloscope on the left and the Siglent SDG1032X Arbitrary Waveform Function Generator on the right, presented as a complete bundle.

2. Alaye Aabo

Always observe the following safety precautions to prevent injury and damage to the instruments:

• Rii daju pe ipese agbara voltage matches the instrument's requirements.
• Maṣe ṣiṣẹ ni tutu tabi damp awọn ipo.
• Má ṣe ṣí ohun èlò orin náà casing; tọ́ka sí iṣẹ́ ìtọ́jú fún àwọn òṣìṣẹ́ tó péye.
• Use only specified probes and accessories.
• Ge asopọ agbara ṣaaju ṣiṣe mimọ.

3. Eto

3.1 SDS1052DL+ Oscilloscope Setup

1. Asopọ agbara: Connect the provided power cord to the oscilloscope's power input and then to a grounded AC power outlet.
2. Asopọ Iwadi: Connect the oscilloscope probes to the BNC input channels (CH1, CH2) on the front panel. Ensure a secure connection.
3. Ilẹ: Attach the probe's ground clip to the circuit's ground point.
4. Agbara Tan: Press the power button on the front panel. The oscilloscope will perform a self-test and display the boot screen.
5. Iṣatunṣe akọkọ: For accurate measurements, perform probe compensation as described in the full user manual.

Figure 2: Front panel of the SDS1052DL+ Oscilloscope

This image shows the front panel of the Siglent SDS1052DL+ Digital Storage Oscilloscope, highlighting the display, control knobs, and input connectors.

3.2 SDG1032X Function Generator Setup

1. Asopọ agbara: Connect the provided power cord to the function generator's power input and then to a grounded AC power outlet.
2. Asopọ jade: Connect the desired output channel (CH1 or CH2) to your circuit using a BNC cable.
3. Agbara Tan: Press the power button on the front panel. The function generator will initialize.

Figure 3: Front panel of the SDG1032X Function Generator

This image displays the front panel of the Siglent SDG1032X Arbitrary Waveform Function Generator, showing its display, keypad, and output connectors.

4. Isẹ

4.1 SDS1052DL+ Oscilloscope Operation

The SDS1052DL+ features a high-resolution LCD display and intuitive controls for signal analysis.

• Àwọn Ìṣàkóso Inaro: Satunṣe voltage per division (V/div) and vertical position for each channel.
• Àwọn Ìṣàkóso Pẹtẹlẹ̀: Adjust time per division (s/div) and horizontal position.
• Eto okunfa: Use the trigger controls to stabilize waveforms. Adjust trigger level, mode (Auto, Normal, Single), and source.
• Awọn iwọn: Access automatic measurements (e.g., Vpp, Vrms, Frequency, Period) via the "Measure" menu. Cursors are available for manual measurements.
• Awọn iṣẹ Iṣiro: The oscilloscope includes math functions such as addition, subtraction, multiplication, division, and Fast Fourier Transform (FFT) for frequency domain analysis.
• Asopọmọra: Utilize the USB host port for saving waveforms and screenshots, and the LAN interface for remote control and data transfer.

Figure 4: SDS1052DL+ Oscilloscope displaying FFT analysis

This image shows the Siglent SDS1052DL+ Oscilloscope with its display showing a waveform and a Fast Fourier Transform (FFT) analysis, demonstrating its advanced measurement capabilities.

4.2 SDG1032X Function Generator Operation

The SDG1032X offers versatile waveform generation capabilities up to 30 MHz.

• Aṣayan Waveform: Choose from standard waveforms (sine, square, ramp, pulse, noise) and arbitrary waveforms.
• Eto Igbohunsafẹfẹ: Use the keypad or rotary knob to set the output frequency. Square waves can be generated up to 30 MHz.
• Amplitude and Offset: Adjust the peak-to-peak amplitude and DC offset of the output signal.
• Iṣatunṣe: Supports various modulation types including AM, FM, PM, FSK, and ASK.
• Ìjáde Ikanni Meji: Both CH1 and CH2 can operate independently or be linked. Phase offset between channels is adjustable.
• Sweep and Burst Modes: Configure sweep functions for frequency or amplitude, and burst modes for generating a specific number of cycles.
• Harmonics Generation: Utilize the harmonics generation mode for specific testing requirements.

Figure 5: SDG1032X Function Generator displaying modulation settings

This image shows the Siglent SDG1032X Function Generator's display, illustrating the settings for amplitude modulation (AM Depth and AM Freq) and other waveform parameters.

5. Itọju

• Ninu: Use a soft, dry cloth to clean the instrument's exterior. For stubborn dirt, a lightly dampened cloth with mild detergent may be used. Ensure no liquid enters the instrument.
• Ibi ipamọ: Store the instruments in a dry, dust-free environment away from direct sunlight and extreme temperatures.
• Iṣatunṣe: A gbani ni niyanju lati ṣe iṣirò lẹẹkọọkan nipasẹ awọn oṣiṣẹ iṣẹ ti o peye lati ṣetọju deede wiwọn.
• Awọn imudojuiwọn sọfitiwia: Ṣayẹwo awọn olupese ká webaaye fun awọn imudojuiwọn famuwia lati rii daju iṣẹ ṣiṣe to dara julọ ati iraye si awọn ẹya tuntun.

6. Laasigbotitusita

Abala yii n ṣalaye awọn ọran ti o wọpọ ti o le ba pade.

• Instrument Does Not Power On:
  • Verify the power cord is securely connected to both the instrument and the power outlet.
  • Ṣayẹwo iṣan agbara fun iṣẹ ṣiṣe.
  • Rii daju pe iyipada agbara wa ni ipo "Titan".
• SDS1052DL+ Stuck on Logo Screen:
  • Disconnect the power cord for at least one minute, then reconnect and attempt to power on again.
  • If the issue persists, contact Siglent customer support.
• Unstable Waveform Display on SDS1052DL+:
  • Adjust the trigger level and trigger mode (e.g., to "Auto" or "Normal").
  • Ensure probes are properly compensated and securely connected.
  • Check for external noise sources affecting the signal.
• No Output from SDG1032X:
  • Ensure the "Output" button for the selected channel is illuminated, indicating the output is enabled.
  • Verify the BNC cable connection to the circuit.
  • Check frequency and amplitude settings to ensure they are within valid ranges.

7. Awọn pato

7.1 SDS1052DL+ Digital Storage Oscilloscope

• Bandiwidi: 50 MHz
• Awọn ikanni: 2
• Akoko gidi SampOṣuwọn: 500 MSA/s
• Ifihan: LCD ti o ga
• Asopọmọra: USB Host, LAN
• Awọn ẹya: Cursors, Math functions (including FFT), Built-in Frequency Counter, Automatic Measurements, Advanced Triggers.

7.2 SDG1032X Arbitrary Waveform Function Generator

• Iwọn Igbohunsafẹfẹ: Up to 30 MHz (Square waves up to 30 MHz)
• Awọn ikanni: 2 (Dual Channel Output)
• Awọn ọna igbi: Sine, Square, Ramp, Pulse, Noise, Arbitrary
• Awọn oriṣi Iṣatunṣe: AM, FM, PM, FSK, ASK
• Awọn ẹya: Sweep, Burst, Harmonics Generation Mode, Adjustable Phase Offset between CH1 and CH2, Built-in Frequency Counter.

8. Atilẹyin ọja ati Support

Siglent Technologies provides a warranty for its products. For specific warranty terms, duration, and conditions, please refer to the warranty card included with your product or visit the official Siglent Technologies website. For technical support, service, or inquiries, please contact Siglent customer service through their official channels.

Note: Unauthorized repairs or modifications may void the product warranty.