Zooz Momentary Push-Button in-Wall Switch ZAC99 Instruction Manual

Ọja Pariview

The Zooz ZAC99 is a momentary push-button in-wall switch designed for various applications requiring temporary contact closure. It is suitable for controlling devices such as garbage disposals or as an accessory switch for Z-Wave dimmer modules to enable local dimming control. This device is not a Z-Wave switch itself but functions as a momentary contact switch.

Awọn ẹya pataki:

• Ohun elo to pọ: Can be used for garbage disposals or as a local control for Z-Wave dimmer modules.
• Momentary Control: Activates a connected device only while the button is pressed.
• Fifi sori ẹrọ Rọ: Compatible with 14 AWG and 12 AWG wires, supporting loads up to 15 A.
• Apẹrẹ Iwapọ: Slim Profile allows for easier installation in standard switch boxes.

Aworan: Iwaju view of the Zooz ZAC99 Momentary Push-Button in-Wall Switch. This image shows the white paddle-style button and the mounting frame.

Alaye Aabo

• IKILO: Risk of Electric Shock. All service should be performed by qualified personnel only.
• Disconnect power at the circuit breaker or fuse box before installation.
• Rii daju pe gbogbo awọn asopọ onirin wa ni aabo ati ni ibamu pẹlu awọn koodu itanna agbegbe.
• Ẹrọ yii jẹ ipinnu fun lilo inu ile nikan.
• Má ṣe kọjá ìwọ̀n ẹrù tó pọ̀jù tí ó jẹ́ 15 Amps.

Fifi sori (Eto)

Follow these steps for safe and proper installation of your Zooz ZAC99 Momentary Push-Button in-Wall Switch.

1. Pa Agbara: Locate the circuit breaker controlling the switch location and turn off the power. Verify power is off using a voltage idanwo.
2. Yọ Yipada to wa kuro: Fi pẹ̀lẹ́pẹ̀lẹ́ yọ àwo ògiri náà kúrò kí o sì tú switch tó wà tẹ́lẹ̀ kúrò nínú àpótí iná mànàmáná. Jà àwọn wáyà náà kúrò nínú switch àtijọ́.
3. Ṣe idanimọ Awọn okun:
   • Line (Hot) Wire: Ojo melo dudu, o mu agbara wa lati inu fifọ iyipo.
   • Fi sori ẹrọ Waya: Typically black, connects to the light fixture or appliance.
   • Waya ilẹ: Bare copper or green, connects to the electrical box or ground screw.
4. Wire the ZAC99 Switch:
   

   Aworan: Pada view of the Zooz ZAC99 switch, illustrating the screw terminals for wiring connections.

   • Connect the Line (Hot) wire to one of the screw terminals on the ZAC99 switch.
   • Connect the Load wire to the other screw terminal on the ZAC99 switch.
   • Connect the Ground wire to the green ground screw on the switch or the electrical box.
   • Ensure all connections are tight and secure. The switch accepts 14 AWG and 12 AWG wires.
5. Gbe Iyipada naa: Carefully push the wired switch into the electrical box. Secure it with the provided screws.
6. Fi Awo Odi sori ẹrọ: Attach the wall plate over the switch.
7. Pada Agbara pada: Tan agbara pada si ẹrọ fifọ.

Akiyesi: This switch is a momentary contact switch. It does not have a neutral wire connection and is designed for simple on/off momentary control. For advanced functionality with Z-Wave dimmer modules, refer to the specific instructions for your Z-Wave device regarding momentary switch configuration.

Awọn ilana Iṣiṣẹ

The Zooz ZAC99 switch provides momentary control based on its application.

For Garbage Disposals or Similar Devices:

• Lati muu ṣiṣẹ: Press and hold the upper part of the paddle switch. The connected device (e.g., garbage disposal) will remain active as long as the button is held.
• Lati Muu ṣiṣẹ: Release the button. The device will turn off.

When Used with a Z-Wave Dimmer Module (Accessory Control):

When configured with a compatible Z-Wave dimmer module (e.g., Aeotec ZW111, Fibaro FGD-212, Qubino ZMNHDD3, ZMNHWD3), the ZAC99 can provide local control for lighting.

• Tan/Pa: Tap the upper part of the paddle switch once to toggle the light on or off.
• Ṣatunṣe Imọlẹ: Press and hold the upper part of the paddle switch to adjust the brightness. Release when the desired brightness level is reached.

Pataki: The Z-Wave dimmer module must be configured to recognize a momentary switch for this functionality. Refer to your Z-Wave dimmer module's instruction manual for specific configuration settings (e.g., parameter settings for momentary switch type).

Itoju

The Zooz ZAC99 switch requires minimal maintenance.

• Ninu: To clean the switch, wipe it with a soft, damp Aṣọ. Má ṣe lo àwọn ohun ìfọṣọ tàbí àwọn ohun èlò ìfọṣọ. Rí i dájú pé agbára ti pa kí o tó fi mọ́.
• Awọn ayẹwo igbakọọkan: Periodically check the wall plate and switch for any signs of damage or loose connections. If any issues are observed, turn off power and consult a qualified electrician.

Laasigbotitusita

If you experience issues with your ZAC99 switch, refer to the following common solutions:

• Ẹrọ Ko Dahun:
  • Ensure power is supplied to the switch at the circuit breaker.
  • Daju pe gbogbo awọn asopọ onirin wa ni aabo ati pe o tọ.
  • Check the connected load (e.g., garbage disposal) to ensure it is functioning correctly.
• Not Controlling Z-Wave Dimmer Module:
  • Confirm that the Z-Wave dimmer module is properly installed and powered.
  • Ensure the Z-Wave dimmer module is configured to operate with a momentary switch. This usually involves adjusting a parameter in your Z-Wave hub or controller settings. Refer to the dimmer module's manual for specific instructions (e.g., Zooz Zen72, Option 19, set to Momentary switch).
  • Verify the wiring between the ZAC99 and the Z-Wave dimmer module is correct according to the dimmer module's accessory switch wiring diagram.
• Switch Feels Stiff or Hard to Press:
  • The switch is designed for a tactile click. If it feels unusually stiff or unresponsive, ensure it is properly seated in the electrical box and not obstructed by the wall plate.

Awọn pato

Atilẹyin ọja ati Support

For warranty information or technical support, please contact Zooz directly. Refer to the official Zooz website or your purchase documentation for the most current support contact details and warranty terms.

Brand: ZOOZ

Olupese: ZOOZ

Webojula: Visit the ZOOZ Store on Amazon