Legrand 1597TRW Tamper Resistant GFCI Wall Outlet User Manual

Ọrọ Iṣaaju

This manual provides detailed instructions for the safe installation, operation, and maintenance of the Legrand 1597TRW Tamper Resistant GFCI Wall Outlet. This device is part of the radiant collection, designed to offer reliable electrical protection in residential and commercial environments. Please read these instructions thoroughly before beginning installation or use.

Alaye Aabo

WARNING: Risk of electric shock. May cause serious injury or death. Turn off power at the circuit breaker or fuse box before installation.

Always disconnect power at the service panel before working with electrical wiring.
Installation must be performed by a qualified electrician or in accordance with all local and national electrical codes.
Do not install in wet locations unless specifically rated for such use.
Rii daju pe gbogbo awọn asopọ waya wa ni aabo ati idabobo daradara.
Test the GFCI outlet monthly to ensure proper operation.

Package Awọn akoonu

Daju pe gbogbo awọn paati wa ṣaaju ki o to bẹrẹ fifi sori:

Legrand 1597TRW Tamper Resistant GFCI Wall Outlet (White)
Iṣagbesori skru
Ilana Afowoyi (iwe yii)

Note: A screwless wall plate is not included and must be purchased separately.

Fifi sori ẹrọ

Follow these steps for proper installation of your GFCI outlet:

Pa Agbara: Locate the circuit breaker or fuse that supplies power to the outlet box. Turn it off completely. Verify power is off using a voltage idanwo.
Yọ Atijọ iṣan kuro: Carefully remove the existing wall plate and outlet from the electrical box. Disconnect the wires from the old outlet, noting which wires were connected to the "LINE" and "LOAD" terminals.
Ṣe idanimọ Awọn okun:
- LINE Wires: These wires bring power from the circuit breaker to the GFCI outlet.
- LOAD Wires: These wires carry power from the GFCI outlet to other downstream receptacles or devices that you want to protect. If there are no downstream receptacles, cap the LOAD wires individually.
- Waya ilẹ: Ojo melo ni a fi bàbà tàbí ewéko ṣe àtìmọ́lé.
Connect Wires to GFCI:
- Sopọ awọn ILA wires to the terminals marked "LINE" on the GFCI outlet.
- Sopọ awọn GBIGBE wires to the terminals marked "LOAD" on the GFCI outlet.
- Sopọ awọn okun waya to the green ground screw.
Pataki: The Legrand 1597TRW features a feed-thru wiring configuration that allows the GFCI to protect downstream receptacles. It also prevents line-load reversal miswire, meaning there will be no power to the face or downstream receptacles if wired incorrectly. An auto-ground clip assures a positive ground to a metal box.
So iṣan naa sori ẹrọ: Carefully fold the wires into the electrical box and secure the GFCI outlet to the box using the provided mounting screws.
Fi Awo Odi sori ẹrọ: Attach the screwless wall plate (not included) over the GFCI outlet.
Pada Agbara pada: Tan agbara pada si ẹrọ fifọ.

Aworan: Iwaju view of the Legrand 1597TRW Tamper Resistant GFCI Wall Outlet. This image shows the two tamper-resistant receptacles, the TEST button (black), and the RESET button (red).

Isẹ

The GFCI outlet is designed to protect against electrical shock by quickly shutting off power if a ground fault is detected.

Bọtini Tuntun: After installation or a power outage, press the red RESET button to restore power to the outlet.
Bọtini idanwo: Press the black TEST button to simulate a ground fault. The GFCI should trip, and power to the outlet will be cut off. This confirms the GFCI is functioning correctly.

Idanwo Oṣooṣu:

It is recommended to test your GFCI outlet monthly to ensure it is providing continuous protection. To test:

Pulọọgi alamp or other device into the GFCI outlet and turn it on.
Press the black TEST button. The lamp should turn off, and the red RESET button should pop out.
Press the red RESET button. The lamp should turn back on.
Ti lamp does not turn off or on as described, the GFCI may be faulty and should be replaced.

Itoju

The Legrand 1597TRW GFCI outlet requires minimal maintenance. Regular testing is the primary maintenance procedure.

Keep the outlet clean and free from dust and debris.
Do not paint over the GFCI outlet or its buttons, as this can impair operation.
If the GFCI trips frequently without an apparent cause, consult a qualified electrician to inspect your wiring.

Laasigbotitusita

Isoro	Owun to le Fa	Ojutu
GFCI will not reset.	Ko si agbara si GFCI. A ṣe awari aṣiṣe ilẹ. Line-load reversal miswire. Faulty GFCI.	Ṣayẹwo Circuit fifọ. Unplug all devices from the GFCI and downstream outlets. Try to reset. If it resets, plug devices back in one by one to identify the faulty device. Verify wiring connections (LINE to LINE, LOAD to LOAD). Replace the GFCI.
GFCI trips frequently.	Faulty appliance/device. Moisture in the circuit. Waya ti bajẹ.	Identify and remove the faulty appliance. Ensure the environment is dry. Kan si onimọ-ẹrọ ina ti o mọye lati ṣayẹwo awọn okun waya.
Ko si agbara si iṣan.	GFCI ṣubu. Bireki Circuit ti kọlu. Ti firanṣẹ ti ko tọ.	Tẹ bọtini atunto. Ṣayẹwo ki o tun ẹrọ fifọ Circuit pada. Ṣe àyẹ̀wò àwọn ìsopọ̀ onírin.

Awọn pato

Awoṣe: 1597TRW
Brand: Legrand
Àwọ̀: Funfun
Ampigba: 15 Amps
Voltage: 125 Volts
Lapapọ Awọn iṣan agbara: 2
Orisi Asopọmọra: Nema 5-15
Ohun elo: Irin
Awọn ẹya: Tamper Resistant, Auto-Ground Clip, Feed-Thru Wiring, Line-Load Reversal Miswire Prevention
UPC: 680147085438
ASIN: B079LTP7Y5

Atilẹyin ọja ati Support

Legrand products are designed and manufactured to the highest quality standards. For specific warranty information, please refer to the documentation included with your purchase or visit the official Legrand website. For technical support or further assistance, please contact Legrand customer service.

Contact information for Legrand can typically be found on their official webaaye tabi apoti ọja.

Legrand 1597TRW