Bontrager Ridetime Bike Computer itọnisọna Afowoyi

1. Eto

This section guides you through the initial setup and installation of your Bontrager Ridetime Bike Computer.

1.1 Unpacking ati Idanimọ paati

Carefully unpack all components from the box. Verify that all parts are present:

• Bontrager Ridetime Bike Computer unit
• Handlebar/Stem mounting bracket
• Analog speed sensor
• Oofa soro
• CR2032 battery (for sensor, may be pre-installed)
• Zip ties for mounting

Nọmba 1: The Bontrager Ridetime Bike Computer shown with all its included components, including the main computer unit, handlebar mount, analog speed sensor, spoke magnet, and zip ties for installation.

1.2 Mounting the Computer

1. Attach the mounting bracket to your bicycle's handlebar or stem using the provided zip ties. Ensure it is securely fastened and positioned for easy viewing.
2. Slide the Bontrager Ridetime computer unit onto the mounting bracket until it clicks into place.

1.3 Installing the Speed Sensor and Spoke Magnet

1. Mount the analog speed sensor to the front fork of your bicycle using the provided zip ties. Position it so that the sensor's alignment mark faces the wheel's spokes.
2. Attach the spoke magnet to a spoke on your front wheel. Ensure the magnet is aligned with the sensor's alignment mark and passes within 5mm of the sensor with each wheel rotation. Adjust the sensor or magnet position as needed to achieve proper alignment and clearance.
3. Confirm the sensor battery (CR2032) is installed. The sensor will activate when the magnet passes it.

2. Awọn ilana Iṣiṣẹ

Learn how to use your Bontrager Ridetime Bike Computer to track your rides.

2.1 Ifihan Loriview

The large, clear display shows key ride metrics. The top section typically displays your current speed, while the bottom section shows the timer or other selected data.

Nọmba 2: A sunmọ-soke view of the Bontrager Ridetime Bike Computer's display, showing a large digital speed reading at the top and a timer function below it. A single button is visible at the bottom of the unit.

2.2 bọtini Awọn iṣẹ

The Bontrager Ridetime computer features a single button for operation, located at the bottom of the unit.

• Tẹ kukuru: Cycles through various display modes (e.g., current speed, average speed, maximum speed, trip distance, total distance, timer).
• Long Tẹ: Resets trip data (trip distance, average speed, maximum speed, timer). Hold the button until the values reset to zero.

2.3 Initial Setup and Wheel Size

Before your first ride, ensure the correct wheel size is set for accurate speed and distance readings. Refer to the instructions that came with your computer for specific steps on entering wheel circumference, as this may vary by production batch. Typically, this involves a sequence of button presses during initial power-on or after a reset.

3. Itọju

Proper care ensures the longevity and accuracy of your bike computer.

3.1 Ninu

Nu kọ̀ǹpútà àti sensọ náà pẹ̀lú ìrọ̀rùn, damp asọ. Ma ṣe lo abrasive ose tabi olomi, bi awọn wọnyi le ba ifihan tabi casing. The unit has an IP54 international protection rating, meaning it is protected from dust ingress and splashing water from any direction. Avoid submerging the unit in water.

3.2 Batiri Rirọpo

The speed sensor uses a CR2032 coin cell battery. When the sensor's signal becomes intermittent or stops, it may be time to replace the battery.

1. Locate the battery compartment on the speed sensor.
2. Use a small coin or screwdriver to open the battery cover.
3. Yọ batiri CR2032 atijọ kuro ki o si fi tuntun sii, ki o rii daju pe o pe polarity (+ ẹgbẹ oke).
4. Pa ideri batiri naa ni aabo.

The main computer unit typically has a long-lasting internal battery or a user-replaceable battery. Refer to the original packaging or manufacturer's website for specific instructions on replacing the main unit's battery if needed.

4. Laasigbotitusita

Awọn oran ti o wọpọ ati awọn ojutu wọn.

4.1 No Speed Reading or Intermittent Data

• Check Sensor-Magnet Alignment: Ensure the spoke magnet passes within 5mm of the speed sensor. Adjust their positions if necessary.
• Batiri sensọ: Replace the CR2032 battery in the speed sensor.
• Iṣalaye sensọ: Verify the sensor is mounted correctly on the fork with its alignment mark facing the magnet.

4.2 Incorrect Speed or Distance Readings

• Eto Iwon Kẹkẹ: Confirm that the correct wheel circumference is programmed into the computer. An incorrect setting will lead to inaccurate data.
• Magnet Position: Ensure the magnet is securely fastened and not slipping on the spoke.

4.3 Ifihan Ko Ṣiṣẹ

• Batiri Ẹka Akọkọ: If the main unit uses a replaceable battery, check and replace it if necessary.
• Tun: Try performing a full reset of the computer (refer to operating instructions for long press function, or look for a small reset button on the back).

5. Awọn pato

6. Atilẹyin ọja ati Support

6.1 atilẹyin ọja Alaye

For detailed warranty information regarding your Bontrager Ridetime Bike Computer, please refer to the warranty card included with your original purchase or visit the official Bontrager webojula. Awọn ofin atilẹyin ọja le yatọ nipasẹ agbegbe ati ọja.

6.2 Onibara Support

If you encounter issues not covered in this manual or require further assistance, please contact Bontrager customer support through their official website or the contact information provided in your product packaging. When contacting support, please have your product model number (1438143873069-13706076454957) and UPC (601479718313) available.