1. Ifihan
This manual provides detailed instructions for the installation, operation, and maintenance of the MEAN WELL RS-150-15 Single Output Switching Power Supply. This high-efficiency power supply delivers a stable 15V DC output with a rated current of 10A, providing 150W of power. It is designed for various industrial and scientific applications, featuring robust protection mechanisms and a compact design.
2. Alaye Aabo ati Awọn akọsilẹ pataki
Please read all safety instructions carefully before installation and operation to prevent injury or damage to the unit. Keep this manual for future reference.
- Aabo gbogbogbo: This power supply is considered a component and must be installed into a final equipment. The final equipment must be re-confirmed to meet all relevant EMC directives.
- Iṣagbewọle Voltage Aṣayan: The unit supports both 88-132VAC and 176-264VAC input ranges, selectable via a switch. Ensure the correct voltage is selected before connecting to the AC mains.
- Awọn ipo Ayika: Operate the power supply within the specified working temperature (-25°C to +70°C) and humidity (20% to 95% RH non-condensing) ranges. Avoid exposure to excessive moisture or extreme temperatures.
- Itutu: The unit is cooled by free air convection. Ensure adequate airflow around the power supply to prevent overheating.
- Awọn ẹya Idaabobo: The power supply includes built-in protections against short circuit, overload, and over voltage. In case of a fault, the unit will enter hiccup mode and automatically recover once the fault condition is removed.
- Asopọmọra: All parameters are measured at 230VAC input, rated load, and 25°C ambient temperature unless otherwise specified. Ripple and noise are measured with a 12" twisted pair-wire terminated with 0.1uF & 47uF parallel capacitors.
- Fifi sori: Ensure proper grounding (FG) connection for safety.
- Agbara-Lori Ọkọọkan: Turning the power supply ON/OFF very quickly may increase the setup time.
3. Awọn ẹya ara ẹrọ
- Universal AC input / Full range (selectable by switch)
- Protections: Short circuit, overload, over voltage
- Itutu nipasẹ free air convection
- Atọka LED fun agbara lori
- 100% ni kikun fifuye iná-ni igbeyewo
- Utilizes 105°C long life electrolytic capacitors
- Withstands 300VAC surge input for 5 seconds
- Iwọn otutu ti n ṣiṣẹ ga soke si 70 ° C
- Withstands 5G vibration test
- Ṣiṣe giga, igbesi aye gigun, ati igbẹkẹle giga
4. Eto ati fifi sori
Proper installation is crucial for the safe and reliable operation of the power supply. Refer to the mechanical specifications and terminal assignments for correct wiring.
4.1 Mechanical Dimensions and Mounting
The power supply features a compact design for easy integration. Ensure sufficient space for air circulation around the unit for optimal cooling.
Nọmba 1: Mechanical dimensions and mounting points of the RS-150-15 power supply. Dimensions are in millimeters. The unit measures 197mm (L) x 98mm (W) x 38mm (H).
Mount the power supply securely using the designated mounting holes as shown in Figure 1. Ensure the mounting surface is stable and can support the weight of the unit (approximately 0.7 kg).
4.2 Terminal Assignment
Connect the input and output wires according to the terminal assignments below. Use appropriate wire gauges for the current ratings to prevent overheating.
| PIN Bẹẹkọ. | Iṣẹ iyansilẹ | PIN Bẹẹkọ. | Iṣẹ iyansilẹ |
|---|---|---|---|
| 1 | AC / N | 4 | DC O wu -V |
| 2 | AC / L | 6 | DC Ijade + V |
| 3 | FG (Ilẹ fireemu) |
Pataki: Ensure the Frame Ground (FG) terminal is properly connected to earth ground for safety.
4.3 Input Voltage Aṣayan
The RS-150-15 has a switch to select between 88-132VAC and 176-264VAC input voltage awọn sakani. Before connecting the power supply to the AC mains, verify that the switch is set to match your local AC supply voltage. Voltagàṣàyàn e le ba ẹ̀rọ náà jẹ́.
5. Awọn ilana Iṣiṣẹ
Once properly installed and wired, the power supply is ready for operation.
- Agbara Tan: Connect the AC input to the power supply. The LED indicator on the unit will illuminate, indicating that the power supply is active.
- O wujade Voltage Atunṣe: Awọn ti o wu voltage can be adjusted within the range of 13.5V to 16.5V using the internal potentiometer. Use a voltmeter to accurately set the desired output voltage.
- Asopọmọra fifuye: Connect your DC load to the +V and -V output terminals. Ensure the load does not exceed the rated current of 10A or the rated power of 150W.
- Ipilẹ Iyipada: For operation at higher ambient temperatures or lower input voltages, refer to the derating curves in the specifications section to ensure the power supply operates within its safe limits.
Nọmba 2: Specification sheet for the RS-150-15, including derating curves and static characteristics. The derating curve illustrates the maximum permissible load at various ambient temperatures, while static characteristics show performance across input voltage awọn sakani.
6. Itọju
The MEAN WELL RS-150-15 power supply is designed for long-term, reliable operation with minimal maintenance. However, adhering to the following guidelines will help ensure its longevity:
- Jeki mimọ: Periodically inspect the unit for dust accumulation, especially around ventilation openings. Clean with a soft, dry cloth or compressed air. Do not use liquid cleaners.
- Rii daju sisan afẹfẹ: Verify that the free air convection cooling is not obstructed. Maintain adequate clearance around the power supply.
- Iṣakoso Ayika: Operate the unit within the specified temperature and humidity ranges. Avoid environments with high levels of corrosive gases or excessive vibration.
- Iduroṣinṣin asopọ: Periodically check all input and output connections to ensure they are secure and free from corrosion.
7. Laasigbotitusita
If the power supply is not functioning as expected, consider the following common issues and their solutions:
- No Output / LED Off:
- Check the AC input connection and ensure power is supplied to the unit.
- Daju igbewọle voltage selection switch is set correctly for your AC mains.
- Inspect the input fuse (if accessible and replaceable) for continuity.
- Intermittent Output / Hiccup Mode:
- This indicates that one of the protection features (short circuit, overload, or over voltage) has been activated.
- Disconnect the load and check for short circuits in your external circuit.
- Ensure the load current does not exceed 10A and the power does not exceed 150W.
- Ṣayẹwo ti o ba ti o wu voltage is set too high (above 16.5V).
- Allow the unit to cool down if it has been operating in a high-temperature environment, as over-temperature protection may be active.
- O wujade Voltage Incorrect:
- Use a voltmeter to measure the output voltage.
- Adjust the internal potentiometer to set the desired output voltage within the 13.5V to 16.5V range.
- Rí i dájú pé ẹrù náà kò fa ìṣàn omi púpọ̀ jù, èyí tí ó lè fa ìfúnpọ̀ omitage ju.
If the problem persists after performing these checks, contact qualified service personnel.
8. Specifications (Model: RS-150-15)
The following table details the technical specifications for the MEAN WELL RS-150-15 power supply.
| Iwa | Iye |
|---|---|
| IJADE | |
| DC Voltage | 15V |
| Ti won won Lọwọlọwọ | 10A |
| Ti won won Agbara | 150W |
| Ripple & Ariwo (o pọju) | 120mVp-p |
| Voltage ADJ. Range | 13.5 ~ 16.5V |
| Voltage Ifarada | ± 1.0% |
| Ilana laini | ± 0.5% |
| fifuye Regulation | ± 0.5% |
| Setup, Rise, Hold Time | 800ms, 30ms, 10ms (at 230VAC full load) |
| ÀWỌN Ọ̀RỌ̀ | |
| Voltage Ibiti | 88 ~ 132VAC / 176 ~ 264VAC (selected by switch) |
| Iwọn Igbohunsafẹfẹ | 47 ~ 63Hz |
| Iṣiṣẹ (Iru.) | 84% |
| AC Lọwọlọwọ (Iru.) | 2.5A/230VAC |
| Inrush Lọwọlọwọ (Iru.) | Ibẹrẹ tutu 40A/230VAC |
| Njo Lọwọlọwọ | <2mA/240VAC |
| IDAABOBO | |
| Apọju | 110 ~ 150% rated output power. Protection type: Hiccup mode, recovers automatically after fault condition is removed. |
| Lori Voltage | 17.25 ~ 20.25V. Protection type: Hiccup mode, recovers automatically after fault condition is removed. |
| Lori iwọn otutu | Bẹẹni |
| Ayika | |
| Awọn iwọn otutu ṣiṣẹ | -25 ~ + 70°C (Tọkasi si Ipilẹ Iyasọtọ) |
| Ọriniinitutu ṣiṣẹ | 20 ~ 95% RH ti kii ṣe idapọmọra |
| Ibi ipamọ otutu | -40 ~ +85°C, 10 ~ 95% RH |
| Olusodipupo iwọn otutu | ±0.03%/°C (0~50°C) |
| Gbigbọn | 10 ~ 500Hz, 5G 10min./1cycle, akoko fun 60min. kọọkan pẹlú X, Y, Z ãke |
| AABO & EMC | |
| Awọn Ilana Abo | UL60950-1, TUV EN60950-1 approved |
| Koju Voltage | I/P-O/P:3KVAC, I/P-FG:1.5KVAC, O/P-FG:0.5KVAC |
| Iyapa Resistance | I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25°C/70% RH |
| Imukuro EMC | Compliance to EN55022 (CISPR22) class B, EN61000-3-2,-3 |
| EMC ajesara | Compliance to EN61000-4-2,3,4,5,6,8,11, EN61000-6-2 (EN50082-2), heavy industry level, criteria A |
| OMIRAN | |
| MTBF | 244Khrs min. MIL-HDBK-217F (25°C) |
| Iwọn (L x W x H) | 197 x 98 x 38mm |
| Iwọn | 0.7Kg |
9. Atilẹyin ọja ati Support
The MEAN WELL RS-150-15 Switching Power Supply comes with a 3-odun atilẹyin ọja from the date of purchase, covering defects in materials and workmanship under normal use. For warranty claims or technical support, please contact your authorized MEAN WELL distributor or reseller.
For additional information or specific technical inquiries, please refer to the official MEAN WELL webojula tabi kan si wọn onibara iṣẹ Eka.