Hayward W3EC40AC Perflex Diatomaceous Earth Pool Filter Instruction Manual

1. Ọja Ipariview

The Hayward Perflex Extended-Cycle Diatomaceous Earth Pool Filter, model W3EC40AC, is designed to provide clear, sparkling water for above-ground, on-ground, and small in-ground pools. This filter utilizes exclusive Flex-Tube technology and diatomaceous earth (DE) as the filter media, known for its effectiveness in removing fine particles. The design aims for superior water clarity and extended filter cleaning cycles without the need for traditional backwashing.

Figure 1: Hayward W3EC40AC Perflex Diatomaceous Earth Pool Filter.

Figure 2: Hayward W3EC40AC Perflex Filter with pump assembly.

2. Alaye Aabo

IKILO: Failure to follow these instructions can result in severe injury or death. This product must be installed and serviced by a qualified pool professional in accordance with all applicable local and national codes and ordinances.

• Máa yọ agbára kúrò nínú píńpù kí o tó ṣe iṣẹ́ tàbí ìtọ́jú èyíkéyìí.
• Ensure the filter is properly secured and all connections are tight to prevent leaks.
• Má ṣe lo àlẹ̀mọ́ náà bí apá kan bá bàjẹ́ tàbí tí ó bá sọnù.
• Pa awọn ọmọde mọ kuro ninu ohun elo adagun-odo.
• Always wear appropriate personal protective equipment (PPE) when handling pool chemicals or performing maintenance.
• Maintain proper water chemistry to prevent damage to equipment and ensure safe swimming conditions.
• Consult a qualified professional if you are unsure about any installation or maintenance procedures.

3. Eto ati fifi sori

Proper installation is crucial for the efficient and safe operation of your Hayward Perflex filter. Refer to the detailed installation guide provided with your product for specific diagrams and instructions. The following is a general overview:

3.1 Aye Yiyan

• Choose a level, solid base for the filter, preferably in a well-drained area.
• Ensure adequate clearance around the filter for maintenance and service (refer to specifications for required clearance).
• Position the filter to minimize plumbing runs and ensure easy access to controls.

3.2 Plumbing Awọn isopọ

• Connect the pool pump discharge to the filter's inlet port.
• So ibudo iṣan omi àlẹmọ naa pọ mọ laini ipadabọ adagun-odo naa.
• Use appropriate plumbing fittings and sealants to ensure watertight connections.
• Install a pressure gauge on the filter to monitor operating pressure.

3.3 Electrical Awọn isopọ

• Ensure all electrical connections for the pump are made by a qualified electrician and comply with local codes.
• Awọn fifa gbọdọ wa ni ilẹ daradara.

3.4 Initial Start-up and DE Charging

1. Ensure all plumbing connections are secure and the filter drain plug is closed.
2. Fill the pool to the proper operating level.
3. Open all suction and return valves.
4. Ṣii awọn air iderun àtọwọdá lori oke ti awọn àlẹmọ.
5. Start the pump. Once a steady stream of water emerges from the air relief valve, close the valve.
6. With the pump running, slowly add the recommended amount of Diatomaceous Earth (DE) powder into the skimmer. Refer to the filter specifications for the correct DE quantity.
7. Allow the filter to run for several minutes to distribute the DE evenly over the Flex-Tubes.

4. Awọn ilana Iṣiṣẹ

Once installed and charged with DE, your Perflex filter is ready for operation. Monitor the pressure gauge and water clarity to ensure optimal performance.

4.1 Isẹ deede

• The filter should operate with the pump running, circulating pool water through the DE media.
• Note the initial clean filter pressure reading on the pressure gauge. This is your baseline.
• The filter will remove microscopic particles, improving water clarity.

4.2 Extended-Cycle Filtration

The Perflex filter's Flex-Tube technology allows for extended cleaning cycles. As dirt accumulates on the DE, the pressure in the filter will gradually rise. Instead of immediate backwashing, the Perflex system allows for "bumping" to refresh the DE.

5. Itọju

Regular maintenance ensures the longevity and efficiency of your Perflex filter. The primary maintenance task is cleaning the filter when the operating pressure rises.

5.1 When to Clean (Bump) the Filter

• Clean the filter when the pressure gauge reading rises 7-10 PSI above the initial clean filter pressure.
• Clean the filter if water clarity decreases significantly.

5.2 Cleaning Procedure (Bumping)

1. Turn off the pool pump and disconnect power.
2. Ṣii awọn air iderun àtọwọdá lori oke ti awọn àlẹmọ.
3. Operate the "bump" handle (if equipped) or follow the specific instructions for your model to dislodge the DE from the Flex-Tubes. This action reuses the DE and dirt mixture to form new cleaning surfaces.
4. Ti fáìlì ìtura afẹ́fẹ́ pa.
5. Tun fifa soke.
6. If the pressure remains high or water clarity does not improve after bumping, a full disassembly and cleaning of the Flex-Tube assembly may be required.

5.3 Disassembly and Full Cleaning

Periodically, or if bumping does not restore filter performance, a full cleaning of the internal components is necessary. The easy-to-access clamp assembly simplifies this process.

1. Pa fifa naa ki o si ge agbara kuro.
2. Open the air relief valve and drain the filter completely.
3. Yọ clamp assembly that secures the filter head to the tank.
4. Carefully lift the filter head and Flex-Tube assembly out of the tank.
5. Rinse the Flex-Tube assembly thoroughly with a garden hose to remove all DE and debris.
6. Inspect the Flex-Tubes for any damage or tears. Replace if necessary.
7. Clean the inside of the filter tank.
8. Reassemble the filter, ensuring the O-ring is clean and properly seated.
9. Ṣe aabo clamp assembly firmly.
10. Recharge the filter with new DE as per the initial start-up procedure.

6. Laasigbotitusita

This section addresses common issues you might encounter with your Hayward Perflex filter.

7. Awọn pato

8. Atilẹyin ọja & Atilẹyin

Hayward products are manufactured to the highest standards of quality and reliability. For specific warranty information regarding your W3EC40AC Perflex Diatomaceous Earth Pool Filter, please refer to the warranty card included with your product or visit the official Hayward webojula.

For technical support, replacement parts, or service inquiries, please contact Hayward Customer Service. Contact details can typically be found on the Hayward webaaye tabi ni awọn ohun elo apoti.

Awọn orisun Ayelujara: Fun alaye ni afikun, Awọn ibeere FAQ, ati iforukọsilẹ ọja, jọwọ ṣabẹwo si osise naa Hayward webojula.