Herdio 5.25'' Home Audio Package Wall Mount Bluetooth Amplifier Receiver System with In-Ceiling Wall Passive Speakers (Model HCS 528-16BT) Instruction Manual

1. Alaye Aabo

Jọ̀wọ́ ka gbogbo ìlànà ààbò kí o tó fi ọjà yìí sí ojú ọ̀nà tàbí kí o tó lò ó. Àìtẹ̀lé àwọn ìlànà wọ̀nyí lè fa ìkọlù iná mànàmáná, iná, tàbí àwọn ewu mìíràn.

• Orisun Agbara: Use only the provided power adapter. Ensure the power supply voltage baamu awọn ibeere ọja naa.
• Omi ati Ọrinrin: Do not expose this product to water, moisture, or extreme humidity. Avoid installation in areas where water contact is possible.
• Ooru: Do not install near heat sources such as radiators, heat registers, stoves, or other apparatus that produce heat.
• Afẹfẹ: Rii daju dara fentilesonu ni ayika amplifier unit. Do not block any ventilation openings.
• Fifi sori: Installation should be performed by qualified personnel following local electrical codes. Ensure all wiring is secure and properly insulated.
• Ninu: Disconnect power before cleaning. Use a dry cloth only. Do not use liquid cleaners or aerosol cleaners.
• Ṣiṣẹ: Maṣe gbiyanju lati ṣiṣẹ ọja yi funrararẹ. Tọkasi gbogbo iṣẹ si oṣiṣẹ oṣiṣẹ ti o peye.

2. Ọja Ipariview

The Herdio 5.25'' Home Audio Package provides a versatile sound solution for various indoor environments. It includes a wall-mount Bluetooth amplifier receiver and two 5.25-inch in-ceiling passive speakers. The system supports multiple audio input options, including Bluetooth, AUX, and USB, along with a microphone input for paging or announcements.

2.1. Wall Mount Bluetooth AmpOlugba lifier

Iwapọ yii amplifier unit is designed to fit into a standard wall plate, offering convenient access to controls and connectivity. It features a master volume knob, input selection switch, USB port for media playback and device charging, a 3.5mm AUX-in jack, and a 1/4'' MIC-in jack.

olusin 1: Odi Oke Amplifier Controls. This image displays the front panel of the wall-mount amplifier, detailing the power LED, input selection switch (AUX, BT, MIC), USB port, master volume/power knob, MIC IN jack, and AUX IN jack.

Figure 2: USB Interface. This image shows a USB flash drive inserted into the USB input port on the wall-mount amplifier, illustrating its function for media playback or device charging.

2.2. 5.25-inch In-Ceiling Passive Speakers

The system includes two 5.25-inch passive speakers designed for flush mounting in ceilings or walls. These speakers are engineered to reproduce clear sound with good responsiveness, suitable for various audio applications.

Figure 3: In-Ceiling Speaker Design. This image highlights the speaker's design, emphasizing its powerful bass capabilities and integrated coaxial tweeter for balanced audio output.

3. Ohun ti o wa ninu Apoti

Ṣọra awọn akoonu inu rẹ ki o rii daju pe gbogbo awọn nkan wa:

• 1x Bluetooth In-Wall Audio Receiver Wall Plate
• 1x 12V Agbara Ipese
• 2x Screws for Wall Plate Installation
• 2x 5.25-inch In-Ceiling Speakers (Model HCS-528)
• 2x Speaker Wires
• 1x User Manual for Ampitanna
• 1x User Manual for Speakers
• 2x Gaskets for Speakers
• 1x Cutout Template for Speakers

Figure 4: Package Contents. This image displays all components included in the Herdio 5.25'' Home Audio Package, laid out for verification.

4. Eto

4.1. Odi Oke AmpFifi sori ẹrọ lifier

1. Ṣetan Odi naa: Ensure you have a standard electrical wall box available for installation.
2. So okun agbara pọ: Connect the 12V DC power cable (red positive, black negative) to the two-pin connector on the back of the amplifier module.
3. So okun Olohun so pọ: Connect the stereo input audio cable to the three-pin connector on the back of the amplifier module.
4. Gbe awọn Ampolutọpa: Fara fi sii amplifier module into the wall box. Secure it using the provided screws.
5. So Apoti Iwari: Place the decorative faceplate over the amplifier and secure it.

olusin 5: Odi Oke Amplifier Installation. This image illustrates the process of installing the wall-mount amplifier into a standard electrical box.

4.2. Ceiling Speaker Installation

1. Determine Location: Choose appropriate locations in the ceiling or wall for the speakers, ensuring no obstructions behind the surface.
2. Ṣii silẹ: Use the provided cutout template to mark and cut a circular opening in the ceiling/wall. The cutout diameter is 7.3 inches (18.5 cm).
3. Remove Speaker Grille: Gently remove the speaker grille using a small tool or screwdriver.
4. Fi Agbọrọsọ sii: Insert the speaker into the cutout opening.
5. Agbọrọsọ to ni aabo: Tighten the speaker clips with screws to firmly secure the speaker in place.
6. Replace Grille: Carefully place the speaker grille back onto the speaker.

Figure 6: Installation Dimensions. This diagram provides the total speaker diameter (8.46 inches / 21.5 cm), cutout diameter (7.3 inches / 18.5 cm), speaker depth (4.33 inches / 11 cm), and wall plate dimensions (4.5 inches / 11.43 cm height, 2.75 inches / 6.89 cm width).

Figure 7: Removing Speaker Grille. This image shows how to carefully remove the speaker's protective grille.

Figure 8: Securing Speaker Clips. This image demonstrates tightening the speaker clips with screws to ensure a secure fit in the ceiling or wall.

Figure 9: Replacing Speaker Grille. This image shows the final step of placing the speaker grille back onto the installed speaker.

4.3. Fifi okun waya sori ẹrọ naa

1. Connect Speaker Wires to Speakers: Connect the provided speaker wires to the terminals on the back of each speaker. Ensure red wire connects to positive (+) and black wire to negative (-).
2. Connect Speaker Wires to Ampolutọpa: Connect the other end of the speaker wires to the speaker output terminals on the back of the wall-mount amplifier. Use a screwdriver to loosen the terminal screws, insert the wires (red to SPK+, black to SPK-), and tighten the screws to secure the connection.
3. Sopọ Ipese Agbara: Plug the 12V power supply into a standard electrical outlet and connect its DC plug to the 12V DC input jack on the wall-mount amplifier.

5. Awọn ilana Iṣiṣẹ

5.1. Ṣíṣe Àkóso Títan/Pá àti Ìṣàkóso Ìwọ̀n

To power on the system, turn the master volume knob clockwise. You will hear an audible 'drop' sound, and the power LED (PWR) will illuminate. Continue turning the knob clockwise to increase the volume. To power off, turn the knob counter-clockwise until it clicks.

5.2. Aṣayan Input

Use the input selection switch on the amplifier's front panel to choose between AUX, BT (Bluetooth), or MIC inputs.

5.3. Sisopọ Bluetooth

1. Switch the input selector to 'BT'. The Bluetooth LED will flash, indicating it is in pairing mode.
2. Lori ẹrọ alagbeka rẹ (foonuiyara, tabulẹti, ati bẹbẹ lọ), mu Bluetooth ṣiṣẹ ki o wa awọn ẹrọ to wa.
3. Select 'Herdio' from the list of available devices to pair.
4. Once successfully paired, the Bluetooth LED on the amplifier will remain steadily lit.
5. You can now play audio from your device through the Herdio speaker system.

5.4. Using USB Input

Insert a USB flash drive into the USB INPUT port for media playback. The amplifier yoo ṣe awari ati mu ohun ṣiṣẹ laifọwọyi files. This port also functions as a charging port for compatible devices (5V/1A).

5.5. Using AUX-In

Connect an external audio device (e.g., MP3 player, TV) to the 3.5mm AUX IN jack using a stereo audio cable. Switch the input selector to 'AUX' to play audio from the connected device.

5.6. Using MIC-In

Connect a microphone to the 1/4'' MIC IN jack. Switch the input selector to 'MIC' for microphone input. This feature is suitable for paging or making announcements.

6. Itọju

To ensure the longevity and optimal performance of your Herdio audio system, follow these maintenance guidelines:

• Ninu: Lo asọ asọ ti o gbẹ lati sọ di mimọ amplifier faceplate and speaker grilles. Avoid abrasive cleaners, solvents, or harsh chemicals.
• Yiyọ eruku kuro: Máa fi eruku lu àwọn ohun èlò ìgbóhùnsáfẹ́fẹ́ déédéé láti dènà kíkójọpọ̀ ohun tí ó lè ní ipa lórí dídára ohùn.
• Awọn ipo Ayika: Keep the system in a dry environment, away from direct sunlight, extreme temperatures, and excessive dust.
• Ayẹwo onirin: Periodically check all wiring connections for tightness and signs of wear. Loose connections can lead to poor sound quality or intermittent operation.

7. Laasigbotitusita

If you encounter issues with your Herdio audio system, refer to the following common problems and solutions:

8. Awọn pato

9. Atilẹyin ọja ati Support

This Herdio product is covered by a 1-odun Service atilẹyin ọja lati ọjọ ti o ra. Atilẹyin ọja yi ni wiwa awọn abawọn iṣelọpọ ati iṣẹ ṣiṣe labẹ lilo deede.

Atilẹyin ọja naa ko ni aabo ibajẹ ti o ṣẹlẹ nipasẹ:

• Aibojumu fifi sori tabi isẹ.
• Accidents, misuse, abuse, or negligence.
• Awọn atunṣe tabi awọn atunṣe laigba aṣẹ.
• Power surges or lightning strikes.

For warranty claims, technical support, or customer service, please contact Herdio customer support through your retailer or visit the official Herdio webojula fun alaye olubasọrọ.