EKYLIN DC 12V to 5V Micro USB Hardwire Kit

1. Ifihan

This manual provides detailed instructions for the installation, operation, and maintenance of your EKYLIN DC 12V to 5V Micro USB Hardwire Kit. This device is designed to provide a stable 5V power supply to various electronic devices, such as dash cameras, GPS navigators, and other Micro USB powered gadgets, directly from your vehicle's 12V-24V electrical system. Please read this manual thoroughly before installation and use to ensure proper function and safety.

2. Awọn ẹya Ọja

• Voltage Iyipada: Converts DC 12V-24V vehicle input to a stable DC 5V 2.1A output.
• Right Angle Micro USB Plug: Features a right-angle Micro USB connector for convenient and space-saving device connection.
• Iṣiṣẹ to gaju: Achieves a conversion rate of 96% or more, minimizing heat generation.
• Aabo ti o ni kikun: Includes built-in safeguards against over-voltage, over-current, over-temperature, short-circuit, and low car battery voltage auto cut-off.
• Ibamu gbooro: Suitable for dash cameras, GPS navigators, tablets, mobile phones, DVR recorders, and other 5V Micro USB devices.
• Gigun USB: Total length of 10 feet (3 meters) for flexible installation.

3. Awọn pato

4. Package Awọn akoonu

• 1 x EKYLIN DC 12V to 5V Micro USB Hardwire Kit

5. Eto ati fifi sori

Proper installation is crucial for the safe and effective operation of your hardwire kit. If you are unsure about any steps, it is recommended to seek professional assistance.

5.1 Awọn iṣọra aabo

• Always ensure the vehicle's ignition is OFF before beginning installation.
• Disconnect the vehicle's battery negative terminal if you are uncomfortable working with live electrical circuits.
• Carefully test and check the polarity and grounding of your vehicle's electrical system before making connections.
• Má ṣe fi ohun èlò onírin líle náà hàn sí ọrinrin tàbí àwọn iwọn otutu tó le koko.

5.2 Wiring aworan atọkaview

The hardwire kit features two input wires for connection to your vehicle's power source:

• Red Wire (ACC/Battery+): Connects to a switched 12V-24V power source (e.g., an ACC fuse in your fuse box) that turns on and off with the vehicle's ignition.
• White Wire (GND/Battery-): Connects to a reliable ground point on the vehicle's chassis.

Image: Close-up of the red (ACC/Battery+) and white (GND/Battery-) input wires.

5.3 fifi sori Igbesẹ

1. Identify Power Sources: Locate your vehicle's fuse box. Using a circuit tester, identify a fuse that provides switched power (ACC) and a suitable ground point (metal chassis).
2. So Waya Agbara pọ: Use a fuse tap (not included) to connect the red wire (ACC/Battery+) of the hardwire kit to the identified switched power fuse.
3. So Ilẹ Waya: Ni aabo so asopọ naa white wire (GND/Battery-) to a clean, unpainted metal bolt or screw on the vehicle's chassis. Ensure a good electrical connection.
4. Okun Ona: Carefully route the Micro USB cable from the power converter box to the location of your device (e.g., dash cam). Ensure the cable is tucked away neatly and does not interfere with vehicle operation or safety features.
5. So ẹrọ pọ: Plug the right-angle Micro USB connector into your dash camera, GPS navigator, or other compatible 5V device.
6. Iṣe idanwo: Turn on your vehicle's ignition. Your connected device should power on. If not, recheck all connections.

Image: Illustrative diagram of a car interior with suggested cable routing for a dash cam hardwire kit.

6. Awọn ilana Iṣiṣẹ

Once installed, the EKYLIN DC 12V to 5V Micro USB Hardwire Kit operates automatically:

• When the vehicle's ignition is turned on, the hardwire kit will supply 5V power to your connected device.
• When the vehicle's ignition is turned off, the hardwire kit will cease power supply to the device.
• The built-in low car battery voltage auto cut-off feature will automatically stop power delivery if your vehicle's battery voltage drops below approximately 11.2V, preventing complete battery discharge. Power will resume when the voltage reaches approximately 11.6V.

Image: Various devices such as a dash cam, tablet, mobile phone, and other USB devices connected to the hardwire kit.

7. Laasigbotitusita

If you encounter issues with your hardwire kit, please refer to the following troubleshooting steps:

• Ẹrọ ti ko ni agbara:
  • Ensure all connections (ACC, Ground, Micro USB) are secure and properly seated.
  • Check the fuse connected to the ACC wire. Replace if blown.
  • Rí i dájú pé iná ọkọ̀ náà wà nílẹ̀.
  • Idanwo igbewọle voltage at the hardwire kit's red wire to ensure it receives 12V-24V when the ignition is on.
  • Confirm your device requires 5V Micro USB power.
• Agbara Laarin:
  • Check for loose connections, especially the ground wire.
  • Ensure the fuse tap is making good contact.
  • Monitor your car battery voltage. Awọn kekere voltage cut-off may be activating if the battery is weak.
• Device Not Charging/Low Output:
  • Ensure the Micro USB cable is fully inserted into your device.
  • Verify your device is not drawing more than 2.1A, which is the maximum output of this kit.
• Hardwire Kit Overheating:
  • Ensure the converter box is not covered or placed in an area with poor ventilation.
  • Confirm your device's power requirements are within the kit's specifications (5V 2.1A max).

8. Itọju

The EKYLIN DC 12V to 5V Micro USB Hardwire Kit requires minimal maintenance:

• Periodically check all electrical connections to ensure they remain secure.
• Keep the converter box free from dust and debris.
• Avoid exposing the unit to excessive moisture or direct sunlight for prolonged periods.

9. Onibara Support

For any questions, concerns, or assistance with your EKYLIN DC 12V to 5V Micro USB Hardwire Kit, please contact our customer support. We are committed to resolving any issues you may encounter.