GOOLOO GP80 800A Peak SuperSafe Car Jump Starter User Manual

1. Ifihan

Thank you for choosing the GOOLOO GP80 800A Peak SuperSafe Car Jump Starter. This portable and powerful device is designed to jump start 12V vehicles with up to 4.5L gas engines, and can also serve as a portable power bank for charging various electronic devices. Please read this manual carefully before use to ensure safe and optimal performance.

Image: The GOOLOO GP80 jump starter connected to a car battery, demonstrating its primary function.

2. Alaye Aabo pataki

Always observe the following safety precautions when using the GOOLOO GP80 jump starter:

• Maṣe ṣe immerse the unit in water or expose it to rain.
• Maṣe ṣe operate the unit if it has been severely damaged or dropped.
• Maṣe ṣe disassemble the unit. Only qualified service personnel should repair this device.
• Maṣe ṣe use the jump starter to charge non-rechargeable batteries.
• Rii daju pe fentilesonu to dara nigba lilo.
• Jeki kuro ni arọwọto awọn ọmọde.
• Wear eye protection when working near batteries.
• So clampní ọ̀nà tó tọ́: Red to Positive (+) ati Black to Negative (-). Reverse polarity can cause damage.
• Remove the jump starter from the vehicle battery within 30 seconds after the vehicle starts.

3. Package Awọn akoonu

Please check the package contents upon opening. If anything is missing or damaged, contact GOOLOO customer support.

• GOOLOO GP80 Jump Starter
• Smart Jumper Clamps
• USB-C Ngba agbara Cable
• Itọsọna olumulo
• Storage Case (may vary by package)

Image: The GOOLOO GP80 jump starter unit shown with its smart jumper clamps.

4. Ọja Awọn ẹya ara ẹrọ ati irinše

Familiarize yourself with the different parts of your GP80 jump starter:

• Bọtini agbara: Turns the unit on/off and activates the flashlight.
• Atọka Ipele Batiri: LED lights showing the remaining battery capacity.
• USB Output Port (Quick Charge): Fun gbigba agbara awọn fonutologbolori, awọn tabulẹti, ati awọn ẹrọ USB miiran.
• Ibudo Iwọle/Ijade USB-C: For charging the jump starter itself or charging other devices.
• 12V Jump Start Port: Connects to the smart jumper clamps.
• Ina filaṣi LED: Provides illumination, with multiple modes (steady, strobe, SOS).

5. Charging the GP80 Jump Starter

Before first use, fully charge the GP80. It is recommended to recharge the unit every 3 months to maintain battery health, even if not used.

1. Connect the provided USB-C charging cable to the USB-C Input/Output port on the GP80.
2. Connect the other end of the USB-C cable to a USB wall adapter (not included) or a powered USB port.
3. The battery level indicator lights will illuminate and flash during charging. All lights will be solid when fully charged.

A full charge typically takes 3-4 hours depending on the power source.

6. Awọn ilana Iṣiṣẹ

6.1. Fo Bibẹrẹ Ọkọ

Ensure the GP80 is at least 50% charged before attempting to jump start a vehicle.

1. Connect the Smart Jumper Clamps: Insert the blue plug of the smart jumper clamps into the 12V Jump Start Port on the GP80. Ensure it is fully inserted.
2. So pọ mọ batiri ọkọ ayọkẹlẹ:
   • Sopọ awọn Pupa (+) clamp si ebute rere ti batiri ọkọ ayọkẹlẹ.
   • Sopọ awọn DUDU (-) clamp to the negative terminal of the car battery or a solid metal part of the car chassis (unpainted metal).

   Awọn ọlọgbọn clamps have indicator lights and an audible alarm for safety. Refer to the clamp's manual for specific error codes.
3. Bẹrẹ Ọkọ naa: Ni kete ti clamps are correctly connected and the smart clamp indicator light is solid green, start your vehicle's engine.
4. Yọ Clamps: As soon as the vehicle starts, remove the smart jumper clamps from the car battery first, then disconnect the blue plug from the GP80.

Pataki: Do not crank the engine for more than 3 seconds. If the vehicle does not start, wait at least 30 seconds before attempting again. Do not attempt more than 3 consecutive jump starts.

6.2. Charging Mobile Devices

The GP80 can also function as a portable power bank.

1. Connect your device's USB charging cable to either the USB Output Port (Quick Charge) or the USB-C Input/Output Port on the GP80.
2. So opin miiran ti okun pọ si ẹrọ alagbeka rẹ.
3. The GP80 will automatically begin charging your device.

6.3. Lilo filaṣi LED

The built-in LED flashlight has multiple modes for convenience.

• Press and hold the Power Button for 3 seconds to turn on the flashlight (steady mode).
• Press the Power Button once to switch to Strobe mode.
• Press the Power Button again to switch to SOS mode.
• Press the Power Button once more to turn off the flashlight.

7. Itọju

Proper maintenance ensures the longevity of your GP80 jump starter.

• Ibi ipamọ: Store the unit in a cool, dry place away from direct sunlight and extreme temperatures. The ideal storage temperature is between -20°C to 60°C (-4°F to 140°F).
• Ngba agbara: Recharge the unit at least once every three months to prevent deep discharge and prolong battery life.
• Ninu: Lo aṣọ rírọrùn tí ó gbẹ láti nu ẹ̀rọ náà. Má ṣe lo àwọn kẹ́míkà líle tàbí àwọn ohun èlò ìpalára.
• Itọju Batiri: Avoid fully discharging the battery frequently. Charge it when the battery indicator shows 2-3 bars.

8. Laasigbotitusita

9. Awọn pato

10. Atilẹyin ọja ati Support

GOOLOO products come with a standard warranty. For detailed warranty information, product registration, or technical support, please visit the official GOOLOO website or contact their customer service team. Keep your purchase receipt as proof of purchase.

GOOLOO Official Webojula: www.gooloo.com

Imeeli Iṣẹ Onibara: support@gooloo.com