Hormann HSE 4 BS Hand Transmitter User Manual

1. Ifihan

This manual provides essential information for the proper setup, operation, and maintenance of your Hormann HSE 4 BS Hand Transmitter. This device is designed for convenient control of compatible garage door and gate operators. Please read these instructions carefully before using the product to ensure safe and efficient operation.

2. Awọn ilana aabo

• Keep the hand transmitter out of reach of children to prevent accidental operation.
• The device is intended for use in dry environments only. Avoid exposure to moisture, rain, or extreme temperatures.
• Do not attempt to open or repair the hand transmitter yourself. Refer to qualified personnel for service.
• Ensure the area around the garage door or gate is clear before operating to prevent injury or damage.
• Sọ awọn batiri ti a lo ni ibamu si awọn ilana agbegbe.

3. Package Awọn akoonu

Daju pe gbogbo awọn nkan wa ninu apo rẹ:

• 1x Hormann HSE 4 BS Hand Transmitter (Classic Grey Chrome)
• 1x CR2032 Lithium Button Cell Battery (pre-installed or included separately)
• 1x Key Ring

4. Ọja Ipariview

The Hormann HSE 4 BS Hand Transmitter is a compact and durable remote control featuring a high-gloss plastic surface with chrome-plated die-cast zinc caps. It is designed for ease of use with a single button operation.

Image showing the Hormann HSE 4 BS hand transmitter, a compact remote control with a high-gloss classic grey finish and chrome accents. It features a single button and a key ring attachment.

5. Eto

5.1. Fifi sori batiri

The hand transmitter uses a 3V Lithium button cell battery, type CR2032. The battery is typically pre-installed. If replacement is needed:

1. Fara ṣii casing of the hand transmitter.
2. Yọ batiri CR2032 atijọ kuro.
3. Insert the new CR2032 battery with the positive (+) side facing up.
4. Pa casing ni aabo.

5.2. Programming the Hand Transmitter

The HSE 4 BS hand transmitter supports both BiSecur radio and fixed code 868 MHz operation. The programming procedure depends on your specific garage door or gate operator model.

General Programming Steps (Refer to your operator's manual for detailed instructions):

1. Activate the programming mode on your garage door or gate operator. This usually involves pressing a 'P' or 'Learn' button on the operator's control unit. Consult your operator's manual for the exact location and procedure.
2. While the operator is in programming mode, press and hold the button on your HSE 4 BS hand transmitter that you wish to program.
3. Hold the button until the operator's indicator light confirms successful programming (e.g., flashes, changes color, or turns off).
4. Release the button on the hand transmitter.
5. Test the hand transmitter to ensure it operates the door or gate correctly.

For specific programming instructions for your Hormann operator, please refer to the operator's instruction manual or visit the official Hormann webojula.

6. Awọn ilana Iṣiṣẹ

To operate your garage door or gate:

1. Ensure you are within range of your garage door or gate operator.
2. Press the single button on the HSE 4 BS hand transmitter.
3. The door or gate will begin to open or close. Pressing the button again during operation will typically stop the movement.

7. Itọju

7.1. Batiri Rirọpo

When the range of your hand transmitter decreases significantly, or if the indicator light (if present) does not illuminate, it is likely time to replace the battery. Follow the steps outlined in Section 5.1 for battery installation.

7.2. Ninu

Clean the hand transmitter with a soft, dry cloth. Do not use abrasive cleaners or solvents, as these can damage the surface.

8. Laasigbotitusita

• Hand Transmitter Not Working: Check if the battery is correctly inserted and has sufficient charge. Replace the battery if necessary. Ensure the hand transmitter is properly programmed to your operator.
• Idinku Idinku: This often indicates a low battery. Replace the CR2032 battery. Obstructions between the hand transmitter and the operator's receiver can also reduce range.
• Door/Gate Not Responding: Verify that the operator itself is powered and functioning correctly. Check for any physical obstructions preventing the door or gate from moving.

If problems persist, consult your garage door or gate operator's manual or contact Hormann customer support.

9. Awọn pato

10. Atilẹyin ọja ati Support

For information regarding warranty terms and conditions, please refer to the documentation provided with your garage door or gate operator, or visit the official Hormann website. If you require technical assistance or have questions not covered in this manual, please contact Hormann customer support.