Saooer 20A Solar Charge Controller User Manual

Ọrọ Iṣaaju

This manual provides essential information for the safe and efficient operation of your Saooer 20A Solar Charge Controller. This intelligent regulator is designed to manage the working of solar panels and batteries in a solar system, featuring dual USB ports for mobile device charging. It is compatible with 12V and 24V systems and includes multiple protection functions to ensure system efficiency and prolong battery lifespan.

olusin 1: Iwaju view of the Saooer 20A Solar Charge Controller.

Awọn Itọsọna Aabo

• Ensure all connections are correct before powering on the controller. Incorrect wiring can damage the device or connected components.
• The controller is designed for indoor use or in a protected environment. Avoid exposure to direct sunlight, high temperatures, or moisture.
• Do not attempt to disassemble or repair the controller yourself. Refer to qualified personnel for service.
• Jeki kuro ni arọwọto awọn ọmọde.
• This controller is only suitable for lead-acid batteries: OPEN, AGM, GEL. Do not use with other battery types like Lithium-ion or LiFePO4, as this may cause damage or safety hazards.
• Always connect the battery first, then the solar panel, and finally the load. When disconnecting, reverse the order: disconnect the load, then the solar panel, and finally the battery.

Ọja Awọn ẹya ara ẹrọ

• Automatic System Voltage Idanimọ: Automatically detects 12V/24V system voltage.
• Gbigba agbara PWM: Efficient Pulse Width Modulation charging mode.
• Meji okun USB: Provides 5V/2A output for charging mobile devices.
• Ifihan LCD: Clear display of status and data, allowing for convenient mode switching and parameter configuration.
• Awọn iṣẹ Idaabobo lọpọlọpọ: Includes short-circuit protection, open-circuit protection, reverse protection, and over-load protection.
• Awọn paramita ti o le ṣatunṣe: User-adjustable charge and discharge parameters.
• Biinu iwọn otutu: Automatic temperature compensation for optimal charging.

Eto ati fifi sori

Follow these steps carefully to install your solar charge controller. Incorrect installation can lead to damage or malfunction.

1. Mura Waya: Ensure all wires are properly stripped and have appropriate connectors if necessary. Use wires of sufficient gauge for your system's current.
2. So batiri pọ: Connect the battery to the charge regulator first. Observe correct polarity (+ to + and - to -). The controller will automatically recognize the battery voltage (12V tabi 24V).
   

   olusin 2: Apa view showing the connection terminals for battery, solar panel, and load.
3. Solar Panel: Connect the solar panel to the solar charge controller. Ensure correct polarity.
4. So fifuye naa pọ: Connect the consumer or load to the charge controller regulator. Ensure correct polarity.

Akiyesi pataki: Always connect the battery first, then the solar panel, and finally the load. When disconnecting the controller, please remove the solar panel, then the load, and finally the battery. This sequence helps the controller recognize the battery voltage correctly and prevents damage.

Awọn ilana Iṣiṣẹ

Ifihan LCD ati Awọn bọtini

olusin 3: Angled view showing the LCD display and control buttons.

The controller features an LCD display and three buttons for operation:

• Bọtini Akojọ: Used to cycle through display modes and enter parameter setting mode.
• Bọtini Soke: Ti a lo lati mu awọn iye pọ si tabi lilö kiri si oke ninu awọn akojọ aṣayan.
• Bọtini isalẹ: Ti a lo lati dinku awọn iye tabi lilö kiri si isalẹ ninu awọn akojọ aṣayan.

Awọn ipo ifihan

Press the Menu button to cycle through the following display modes:

• Batiri Voltage (V)
• Oorun Panel Voltage (V)
• Gbe lọwọlọwọ (A)
• Battery Temperature (°C)
• Gba agbara lọwọlọwọ (A)
• Sisọ lọwọlọwọ (A)
• Load Working Mode (24H, 0-23H, 0H)

Paramita Eto

To enter parameter setting mode, press and hold the Menu button for 5 seconds. Use the Up and Down buttons to adjust values, and the Menu button to confirm and move to the next parameter. Press and hold Menu again to exit setting mode.

Note: For 24V systems, multiply the 12V values by two.

Itoju

• Ayẹwo igbagbogbo: Lokọọkan ṣayẹwo gbogbo awọn asopọ onirin fun wiwọ ati ipata.
• Mimọ: Keep the controller clean and free from dust. Use a dry cloth for cleaning.
• Afẹfẹ: Rí i dájú pé afẹ́fẹ́ tó péye wà ní àyíká olùdarí náà láti dènà kí ó má ​​baà gbóná jù.
• Ilera Batiri: Bojuto batiri voltage and health regularly. Replace batteries as needed.

Laasigbotitusita

Awọn pato

Figure 4: Product dimensions of the solar charge controller.

Atilẹyin ọja ati Support

For warranty information or technical support, please contact the manufacturer, Saooer, through their official channels. Refer to your purchase documentation for specific warranty terms and contact details.

Olupese: Saooer

ASIN: B095764VB7

UPC: 605832982977

O le ṣàbẹwò awọn Saooer Store on Amazon fun alaye diẹ ẹ sii tabi lati kan si atilẹyin.