MokerLink 24-Port 2.5G Managed Ethernet Switch (Model 2G24610GSM) User Manual

1. Ifihan

This manual provides comprehensive instructions for the installation, configuration, operation, and maintenance of the MokerLink 24-Port 2.5G Managed Ethernet Switch. This device is designed to meet diverse networking needs with its high-density 2.5 Gigabit Ethernet ports and 10 Gigabit SFP+ uplinks, offering advanced Layer 2+ and Layer 3 management capabilities.

2. Package Awọn akoonu

Verify the following items are included in your package:

• MokerLink 24-Port 2.5G Managed Ethernet Switch (Model 2G24610GSM)
• Okun agbara
• Ohun èlò Rackmount (tí ó bá wúlò)
• Quick Bẹrẹ Itọsọna

If any items are missing or damaged, please contact MokerLink support.

3. Ọja Ipariview

Figure 3.1: MokerLink 24-Port 2.5G Managed Ethernet Switch with an overview ti awọn oniwe-agbara.

3.1 Key Awọn ẹya ara ẹrọ

• 2.5G Ethernet Ports: 24 x 2.5Gigabit Ethernet Ports, compliant with IEEE802.3bz (2.5G) standard, supporting 10/100/1000M/2.5G adaptive speeds.
• 10G SFP+ Uplink Ports: 6 x 10G SFP+ ports (compatible with 1G/2.5G/10G modules, modules not included).
• Iṣe to gaju: 240Gbps backplane bandwidth and 178.56 Mpps packet forwarding rate for efficient data handling.
• Web L2+ Managed: Supports IPv4/IPv6, ARP configuration, Static Routing, DHCP server/relay/snooping.
• Advanced L2 Configurations: Includes VLAN, QoS, security, multicast, LACP, MAC address table management, and port mirroring.
• Ìṣàkóso Rọrùn: Awọn atilẹyin WEB, CLI, TELNET, USB, SSH, SNMP, and RMON management interfaces.
• Apẹrẹ ti ara: Irin tó le pẹ́ títí casing, desktop or 1U rack-mounting design, fanless for noiseless operation.

Figure 3.2: Speed capabilities of the switch, supporting 2.5Gbps and 10Gbps connections.

3.2 Iwaju Panel Apejuwe

Figure 3.3: Front panel layout with port configuration and LED indicators.

The front panel of the switch features the following components:

• 2.5G RJ45 Ports (1-24): These are the 24 primary Ethernet ports, supporting 10/100/1000Mbps and 2.5Gbps speeds.
• 10G SFP+ Awọn ibudo (25-30): These are the 6 SFP+ slots for 1G/2.5G/10G fiber optic modules.
• PWR (Agbara) LED: Indicates power status. Green for power on, no light for power off.
• SYS (System) LED: Indicates system status. Slow flash indicates normal operation.
• Bọtini atunto: Short press to restart the device. Press and hold for 5 seconds to restore factory settings.
• Ibudo Kọnsole: For command-line interface (CLI) access and management.
• Port LEDs (2.5Gbps Ports):
  • Orange: 10/100/1000Mbps link speed.
  • Green: 2.5Gbps link speed.
  • Flashing: Data transmitting/receiving.
  • Off: Link down.
• Port LEDs (10Gbps Ports):
  • Blue: 10Gbps link speed.
  • Green: 2.5Gbps link speed.
  • Flashing: Data transmitting/receiving.
  • Off: Link down.

3.3 Ru Panel Apejuwe

The rear panel typically includes the AC power input (100-240V, 50/60Hz) and a grounding screw. Ensure proper power connection and grounding for stable operation.

4. Fifi sori ẹrọ ati Oṣo

4.1 Ayika riro

• Place the switch on a stable, flat surface or mount it in a standard 1U rack.
• Ensure adequate ventilation around the device. Avoid blocking ventilation holes.
• Keep the switch away from direct sunlight, heat sources, and excessive moisture.
• Iwọn otutu ti nṣiṣẹ: 0°C si 40°C (32°F si 104°F).

4.2 Asopọ agbara

1. Connect the provided power cord to the AC power input on the rear panel of the switch.
2. Pulọọgi opin miiran ti okun agbara sinu iṣan itanna ti o wa lori ilẹ.
3. Verify the PWR LED on the front panel illuminates green, indicating the switch is powered on.

4.3 Asopọ Nẹtiwọọki

Figure 4.1: Connecting various network devices to the switch.

1. Connect your network devices (e.g., computers, servers, NAS, Wi-Fi 6 APs) to the 2.5G RJ45 ports (1-24) using standard Ethernet cables (CAT5e, CAT6, or CAT6a for optimal performance).
2. For 10G fiber optic connections, insert compatible SFP+ modules (1G/2.5G/10G) into the SFP+ ports (25-30) and connect fiber optic cables.
3. The switch supports auto MDI/MDIX, so straight-through or crossover cables can be used interchangeably.
4. Observe the port LEDs to confirm link status and speed.

4.4 Initial Access to Management Interface

To configure the switch, you can access its web-based management interface or Command Line Interface (CLI).

• Adirẹsi IP aiyipada: 192.168.2.1
• Orukọ olumulo aiyipada: abojuto
• Ọrọigbaniwọle aiyipada: abojuto

Ensure your computer's IP address is in the same subnet (e.g., 192.168.2.x with subnet mask 255.255.255.0) to access the switch's default IP.

5. Isẹ ati Management

5.1 Web Atọka Iṣakoso

Nọmba 5.1: Web and Command Line Interfaces for switch management.

Lati wọle si awọn web ni wiwo:

1. Ṣii a web kiri lori kọmputa kan ti a ti sopọ si awọn yipada.
2. Enter the switch's IP address (default: 192.168.2.1) in the address bar and press Enter.
3. Enter the default username (admin) and password (admin) when prompted.
4. Upon successful login, you will be presented with the switch's management dashboard. It is recommended to change the default password immediately for security.

5.2 Command Line Interface (CLI)

The CLI provides advanced configuration options and is accessible via the console port (using a serial cable and terminal emulator) or via SSH/Telnet over the network.

5.3 Iṣeto Nẹtiwọọki Ipilẹ

The switch supports various Layer 2+ and Layer 3 features for network optimization and security.

5.3.1 VLAN iṣeto ni

Figure 5.2: VLAN segmentation for network isolation.

Virtual Local Area Networks (VLANs) allow you to logically segment your network into separate broadcast domains. This enhances security and improves network performance by reducing unnecessary traffic. The switch supports 802.1Q tag-based VLANs. Refer to the user manual for detailed configuration steps.

5.3.2 Didara Iṣẹ (QoS)

Figure 5.3: QoS prioritization of network traffic.

QoS allows you to prioritize network traffic, ensuring critical applications (e.g., VoIP, video conferencing) receive sufficient bandwidth and experience minimal latency. You can configure QoS based on port, 802.1p, or DSCP values.

5.3.3 Link Aggregation (LACP)

Figure 5.4: Link Aggregation for enhanced bandwidth and redundancy.

Link Aggregation Control Protocol (LACP) allows you to group multiple physical links into a single logical link. This increases bandwidth and provides redundancy, improving network resilience.

5.3.4 Aimi afisona

Figure 5.5: Static routing between different VLANs.

As a Layer 3 managed switch, this device supports static routing, enabling it to forward traffic between different IP subnets or VLANs without requiring an external router for simple inter-VLAN routing scenarios.

6. Itọju

6.1 famuwia imudojuiwọn

Periodically check the MokerLink official website for firmware updates. Firmware updates can provide new features, performance improvements, and security patches. Follow the instructions provided with the firmware package carefully to avoid damaging the device.

6.2 Cleaning and Environmental Care

• Rii daju pe iyipada ti wa ni pipa ati ge asopọ lati orisun agbara ṣaaju ṣiṣe mimọ.
• Use a soft, dry cloth to wipe the exterior of the switch. Do not use liquid or aerosol cleaners.
• Jẹ́ kí àwọn ihò afẹ́fẹ́ má ṣe sí eruku àti ìdọ̀tí láti mú kí afẹ́fẹ́ inú omi tó yẹ kí ó sì gbóná jù.
• Operate the switch within the recommended temperature and humidity ranges.

7. Laasigbotitusita

7.1 Wọpọ Oran ati Solusan

• Ko si Agbara: Check the power cord connection and the electrical outlet. Verify the PWR LED is illuminated.
• Ko si Ọna asopọ lori Port: Ensure the Ethernet cable is securely connected at both ends. Check the cable for damage. Verify the connected device is powered on and functioning correctly. Check the port LED status.
• Ko le Wiwọle Web Ni wiwo:
  • Verify your computer's IP address is in the same subnet as the switch (default: 192.168.2.x).
  • Ensure the correct IP address (default: 192.168.2.1) is entered in the browser.
  • Pa cache browser rẹ rẹ́ tàbí kí o gbìyànjú browser mìíràn.
  • If the IP address was changed and forgotten, consider performing a factory reset (refer to Section 3.2 for Reset Button).
• Iṣe Nẹtiwọọki O lọra:
  • Check port LEDs for correct link speed (Green for 2.5G, Blue for 10G).
  • Ensure cables are appropriate for the desired speed (e.g., CAT6/6a for 2.5G/10G).
  • Verify no network loops are present.
  • Check for high CPU or memory utilization on the switch via the management interface.

7.2 LED Indicator Reference

Refer to Section 3.2 for a detailed explanation of the LED indicators and their meanings, which can assist in diagnosing network issues.

8. Imọ ni pato

9. Atilẹyin ọja ati Support

9.1 atilẹyin ọja Alaye

The MokerLink 24-Port 2.5G Managed Ethernet Switch comes with a 1-year limited warranty from the date of purchase. This warranty covers defects in materials and workmanship under normal use. It does not cover damage caused by misuse, accidents, unauthorized modifications, or improper installation. Please retain your proof of purchase for warranty claims.

9.2 Imọ Support

For technical assistance, troubleshooting, or product inquiries, please contact MokerLink customer support. Refer to the MokerLink official webAaye fun alaye olubasọrọ tuntun, awọn ibeere ti a beere nigbagbogbo, ati awọn orisun afikun.