Ọrọ Iṣaaju
This instruction manual provides comprehensive guidance for the installation, operation, and maintenance of your Vrabocry 5V 5050 RGB LED Strip Light. Please read this manual thoroughly before use to ensure proper functionality and safety.
Package Awọn akoonu
Daju pe gbogbo awọn nkan ti a ṣe akojọ rẹ si isalẹ wa ninu package rẹ:
- 4 x LED Strip Lights (each 1.64ft / 50cm)
- 1 x 44-Key IR Remote Control (battery not included)
- 1 x USB Controller Cable
- 3 x Strip Connector Cables
Image: All components included in the Vrabocry LED Strip Light package.
Awọn pato
| Ẹya ara ẹrọ | Sipesifikesonu |
|---|---|
| LED Iru | SMD 5050 RGB |
| Rinhonu Gigun | 4 x 1.64ft (50cm) sections |
| PCB Iwọn | 10mm |
| Awọn LED opoiye | 30 LEDs per 50cm section |
| LED Awọ | RGB (Multi-color) |
| Ọna Iṣakoso | 44-Key IR Remote Control |
| Ṣiṣẹ Voltage | USB DC 5V |
| Mabomire Oṣuwọn | IP30 (Non-Waterproof) |
| Alamora | Double-sided tape on back |
| inu ile / ita gbangba Lilo | Lilo inu ile Nikan |
Alaye Aabo
- This LED strip light is designed for inu ile nikan. It is not waterproof (IP30 rated). Avoid exposure to water or high humidity.
- Ensure the power source is 5V DC USB. Using an incorrect voltage le ba ọja naa jẹ.
- Do not cover the LED strips with flammable materials when in operation.
- Jeki kuro ni arọwọto awọn ọmọde.
Eto ati fifi sori
Follow these steps to install your LED strip lights:
- Ṣetan Ilẹ: Clean the surface where the LED strips will be installed. Ensure it is dry and free of dust or grease for optimal adhesive performance.
- Fi Batiri Latọna jijin sori ẹrọ: Open the battery compartment on the back of the 44-key IR remote control and insert a CR2025 button cell battery (not included), ensuring correct polarity.
- Connect the Strips: Connect the individual LED strip sections using the provided strip connector cables. Ensure the arrows on the connectors align with the '+' markings on the LED strips for proper electrical connection.
- Connect to USB Controller: Attach the assembled LED strip to the USB controller cable.
- Adhere the Strips: Peel off the protective backing from the double-sided tape on the back of the LED strips. Firmly press the strips onto the cleaned surface. For long-term use, consider reinforcing the adhesive with additional glue or by gently heating the tape with a hairdryer before application to improve adhesion.
- Gígé àwọn ìlà náà (Àṣàyàn): The LED strips can be cut at designated marks (usually indicated by a scissor icon or copper pads) to fit specific lengths. Cut only along these marks to avoid damaging the circuit.
- Agbara Tan: Plug the USB controller into a 5V USB power source (e.g., TV USB port, USB wall adapter, power bank).
Image: Remote control battery compartment. Battery is not included.
Image: Visual guide for surface preparation, strip connection, and cutting points.
Awọn ilana Iṣiṣẹ
Use the 44-key IR remote control to manage your LED strip lights:
Image: 44-Key IR Remote Control layout and functions.
- Titan/Apapa: Tẹ awọn TAN/PA bọtini.
- Atunse Imọlẹ: Lo awọn Imọlẹ + ati Ìmọ́lẹ̀ - arrows to increase or decrease light intensity.
- Awọn awọ Aimi: Select from 20 preset static colors, including Red, Green, Blue, and White, by pressing the corresponding color buttons.
- DIY Color Setting:
- Tẹ ọkan ninu awọn DIY1 si DIY6 awọn bọtini.
- Lo awọn Pupa, Alawọ ewe, Blue arrow buttons (e.g., Red+, Red-) to adjust the intensity of each primary color.
- Tẹ kanna DIY button again to save your custom color.
- Awọn ọna Yiyi:
- LATIO: Cycles through various dynamic modes automatically.
- YARA/O lọra: Ṣe àtúnṣe iyàrá àwọn ipò oníyípadà.
- JUMP3/JUMP7: Jumps between 3 or 7 different colors.
- FADE3/FADE7: Fades between 3 or 7 different colors.
- FILASI: Flashes through different colors.
Itoju
- Ninu: Gently wipe the LED strips with a dry, soft cloth to remove dust. Do not use liquid cleaners or immerse in water.
- Lilemọ: If the adhesive tape loses its stickiness over time, you may reinforce it with additional double-sided tape or a suitable adhesive.
- Ibi ipamọ: When not in use for extended periods, store the LED strips in a cool, dry place away from direct sunlight.
Laasigbotitusita
| Isoro | Owun to le Fa | Ojutu |
|---|---|---|
| LED strips do not light up. | No power, incorrect connection, remote battery depleted. | Ensure USB power source is active. Check all connections, especially arrow alignments. Replace remote battery. |
| Isakoṣo latọna jijin ko ṣiṣẹ. | Battery depleted, IR receiver blocked, remote too far. | Replace remote battery. Ensure clear line of sight between remote and IR receiver on the USB controller. Operate within 5-8 meters. |
| Àwọn àwọ̀ kò tọ́ tàbí kò báradé. | Incorrect connection, faulty strip section. | Verify all strip connector cables are correctly aligned (arrow to '+'). If one section is consistently problematic, it may be faulty. |
| Adhesive tape not sticking well. | Surface not clean, cold temperature. | Clean surface thoroughly. Gently heat the adhesive tape with a hairdryer before application to improve stickiness. Consider additional adhesive. |
Atilẹyin ọja ati Support
Specific warranty information for this product is not provided in the available documentation. For warranty inquiries or technical support, please contact Vrabocry customer service through your purchase platform or the manufacturer's official contact channels.