Powkey A9
Ìwé Àgbékalẹ̀ Olùlò fún Ìbẹ̀rẹ̀ Ọkọ̀ Powkey 2000A
Awoṣe: A9
Alaye Aabo pataki
Please read and understand all safety information before using this product. Failure to follow these instructions may result in electrical shock, explosion, fire, which may result in serious injury, death, or property damage.
- Do not operate the jump starter if it is damaged.
- Maṣe bẹrẹ bẹrẹ batiri tio tutunini.
- Rí i dájú pé ìsopọ̀ polarity tó tọ́ (púpù clamp si rere, dudu clamp si odi).
- Jeki kuro ni arọwọto awọn ọmọde.
- Ma ṣe fi ẹrọ naa bọ inu omi.
- Use only the provided smart jumper cables.
- Do not short-circuit the clamps.
- Tọju ni itura kan, ibi gbigbẹ.
Ọja Pariview
The Powkey 2000A Car Jump Starter (Model A9) is a portable and powerful device designed to jump start vehicles, charge mobile devices, and provide emergency lighting.
Figure 1: Powkey Jump Starter with key components labeled, including power button, battery indicator, USB-C input, USB outputs, DC output, and jump start port.
Awọn ẹya pataki:
- Isan omi 2000A: Capable of jump starting gasoline engines up to 8.0L and diesel engines up to 6.5L.
- Agbara 20000mAh: Provides multiple jump starts on a single charge.
- Meji okun USB: Includes a Quick Charge 3.0 port for fast charging of mobile devices.
- 12V-16V/6A DC Output: For powering other car accessories.
- 3-in-1 LED Flashlight: Features illumination, strobe, and SOS modes.
- UltraSafe Smart Clamps: Built-in protection against short-circuits, overloads, overcurrents, overheating, reverse connection, and reverse polarity.
- Apẹrẹ ti o tọ: IP66 water-resistant, dustproof, and shockproof.
Awọn pato
| Paramita | Iye |
|---|---|
| Awoṣe | A9 |
| Agbara | 20000 mAh |
| Oke Lọwọlọwọ | 2000 A |
| Ṣiṣejade USB 1 | 5V/2.1A |
| Ijade USB 2 (QC3.0) | 5V/3A, 9V/2A, 12V/1.5A |
| DC Iṣelọpọ | 12V-16V/6A (5.5 x 2.1mm) |
| USB-C Input | 5V/2A, 9V/2A |
| Ibamu Ọkọ Iru | Déésì tó 8.0L, Díséẹ̀lì 6.5L |
| Awọn iwọn otutu ti nṣiṣẹ | -20°C si 65°C (-4°F si 149°F) |
| Awọn iwọn (L x W x H) | 16.6 x 4 x 8 cm |
| Iwọn | 870 g |
| Mabomire Rating | IP66 |
Gbigba agbara si Jump Starter
Before first use, fully charge the Powkey Jump Starter. It is recommended to recharge the unit every 3-6 months to maintain battery health, even if not in use.
- Connect the provided USB-C cable to the USB-C input port on the jump starter.
- Connect the other end of the USB-C cable to a USB wall charger (not included) or a powered USB port.
- The battery indicator lights will illuminate and flash during charging. All four lights will be solid when fully charged.
Figure 2: The Powkey Jump Starter unit shown with its accessories, including the USB cable for charging.
Awọn ilana iṣiṣẹ: Fò Bibẹrẹ Ọkọ ayọkẹlẹ kan
Rí i dájú pé ó ní agbára tó kéré jù 50% fún olùbẹ̀rẹ̀ ìfò náà kí o tó gbìyànjú láti gbé ọkọ̀ sókè.
- Ṣeto Ọkọ naa: Turn off the vehicle's ignition and all accessories (headlights, radio, air conditioning). Engage the parking brake.
- Connect Smart Clamps: Insert the blue plug of the smart jumper cables firmly into the jump start port on the Powkey unit. Ensure a secure connection.
- Sopọ si Batiri:
- Sopọ awọn PUPA rere (+) clamp si ebute rere (+) ti batiri ọkọ.
- Sopọ awọn DUDU odi (-) clamp sí ibi tí batiri ọkọ̀ náà wà ní òdì (-).
Akiyesi: Tí ó bá jẹ́ pé olóye clamp indicator light is green, the connection is correct and safe to proceed. If it's red or flashing, check connections and battery voltage.
- Bẹrẹ Ọkọ naa: Once the smart clamp indicator is green, start the vehicle's engine. Do not crank for more than 3 seconds. If the vehicle does not start, wait at least 30 seconds before attempting again. Do not attempt more than 3 consecutive starts.
- Yọ Clamps: Once the vehicle starts, immediately remove the black negative (-) clamp from the vehicle battery, then remove the red positive (+) clamp. Finally, disconnect the smart jumper cables from the Powkey unit.
Figure 3: The Powkey Jump Starter connected to a vehicle battery using the smart clamps, ready for jump starting.
Figure 4: The intelligent smart jumper cables, designed with multiple safety protections to prevent incorrect connections and sparks.
Lilo bi Bank Power
The Powkey Jump Starter can also be used to charge various electronic devices via its USB ports or power 12V accessories via its DC output.
Ngba agbara USB:
- Connect your device's USB charging cable to either the USB Output 1 (5V/2.1A) or USB Output 2 (QC3.0) port on the jump starter.
- Press the power button on the jump starter to begin charging. The battery indicator lights will show the remaining charge.
DC Output (12V-16V/6A):
- Connect the provided cigarette lighter adapter to the DC output port on the jump starter.
- Plug your 12V car accessory (e.g., car vacuum, tire inflator) into the cigarette lighter adapter.
- Press the power button to activate the DC output.
Figure 5: The Powkey Jump Starter demonstrating its power bank functionality, charging a smartphone and a tablet via its USB ports.
LED flashlight Išction
Ina LED ti a ṣe sinu rẹ nfunni ni awọn ipo mẹta fun awọn ipo oriṣiriṣi.
- Tan/Pa: Press and hold the power button for approximately 3 seconds to turn the LED flashlight on or off.
- Awọn ọna Yipada: Once the flashlight is on, short press the power button to cycle through the modes:
- Imọlẹ: Standard steady light for general use.
- Ẹ̀ka: Flashing light for signaling or attracting attention.
- SOS: Morse code signal (three short, three long, three short) for emergency situations.
Figure 6: The Powkey Jump Starter's integrated LED flashlight demonstrating its various modes, including illumination, strobe, and SOS.
Itọju ati Ibi ipamọ
- Ninu: Wipe the unit with a soft, dry cloth. Do not use harsh chemicals or abrasive materials.
- Gbigba agbara: Recharge the unit every 3-6 months to prolong battery life, even if not in use.
- Ibi ipamọ: Store the jump starter in a cool, dry place, away from direct sunlight, heat sources, and moisture. Use the provided EVA storage case for protection.
- Iwọn otutu: Avoid storing or operating the unit outside its recommended temperature range (-20°C to 65°C).
Laasigbotitusita
| Isoro | Owun to le Fa | Ojutu |
|---|---|---|
| Jump Starter ko ni tan. | Batiri naa ti yọ patapata. | Gba agbara fun olubere fo naa patapata. |
| Ọkọ ayọkẹlẹ ko bẹrẹ. | Ti ko tọ clamp asopọ. | Rii daju clamps are connected correctly (red to positive, black to negative). Check smart clamp ina Atọka. |
| Vehicle battery is severely damaged or frozen. | The jump starter cannot start a completely dead or damaged battery. Seek professional assistance. Do not attempt to jump start a frozen battery. | |
| Jump starter overheated. | Excessive cranking attempts or continuous use. | Allow the unit to cool down for several minutes before attempting to use it again. |
| Awọn ẹrọ USB ko gba agbara. | Jump starter not turned on or low battery. | Press the power button to activate USB output. Recharge the jump starter if battery is low. |
| Smart clamp indicator is red/flashing. | Reverse polarity, short circuit, or low battery voltage. | Ge asopọ clamps, check connections, ensure correct polarity. If issue persists, the vehicle battery might be too low or faulty. |
If the jump starter is unresponsive, locate the "RST" (Reset) button (usually a small pinhole) and press it with a thin object like a paperclip or toothpick to reset the device.
Ohun ti o wa ninu Apoti
The Powkey 2000A Car Jump Starter package includes the following items:
- Powkey 2000A Car Jump Starter Unit
- Smart Jumper Cables
- USB-C Ngba agbara Cable
- Cigarette Lighter Adapter (DC Output)
- Eva Ipamọ Ibi
- Itọsọna olumulo
Atilẹyin ọja ati Support
Powkey products are designed and manufactured to the highest quality standards. For warranty information or technical support, please refer to the contact details provided on the product packaging or the official Powkey webojula.
For further assistance, you may contact Powkey customer service directly. Please have your model number (A9) and purchase details ready.