1. Ifihan
The ECOELER Motion Sensor Light Switch (Model YM2112) provides automated lighting control using Passive Infrared (PIR) motion detection. This device is designed for single-pole applications and requires a neutral wire for installation. It offers adjustable settings for sensitivity, ambient light detection, and time delay, allowing customization for various indoor environments such as bathrooms, laundry rooms, closets, and garages.
Figure 1: ECOELER Motion Sensor Light Switch with faceplate.
2. Alaye Aabo
- IKILO: Láti yẹra fún iná, ìpayà, tàbí ikú, pa agbára ní ibi tí ẹ̀rọ ìfọ́mọ́ tàbí àpótí fiusi wà kí o sì dán an wò pé agbára ti pa kí o tó fi wáyà sí i.
- Onímọ̀ ẹ̀rọ iná mànàmáná tó mọ̀ nípa rẹ̀ tàbí ẹni tó ní òye tó jinlẹ̀ nípa àwọn wáyà iná mànàmáná gbọ́dọ̀ fi sori ẹ̀rọ náà.
- This device is for single-pole applications only. Do not use in 3-way or multi-way circuits.
- A neutral wire is required for operation. Ensure your electrical box has a neutral wire (typically white) before installation.
- Maṣe kọja wat ti o pọjutage ratings: 150W for LED/CFL, 300W for Incandescent/Halogen.
- Lo okun waya Ejò nikan.
3. Package Awọn akoonu
Daju pe gbogbo awọn paati wa ṣaaju ki o to bẹrẹ fifi sori:
- Motion Sensor Light Switch (YM2112)
- Odi Awo
- Awọn ilana fifi sori ẹrọ
- Iṣagbesori skru (4 ege)
Figure 2: Included components: Motion Sensor Light Switch, wall plate, and mounting screws.
4. Awọn ẹya ara ẹrọ
- Iṣakoso Ọfẹ: Automatically activates lighting upon motion detection.
- Aṣayan Ipo: Choose between Occupancy (OCC) and Vacancy (VAC) modes.
- Awọn Eto Atunṣe: Customizable time delay (15s to 30min), sensitivity (20% to 100%), and ambient light sensing (dark to day).
- Ibamu gbooro: Supports LED/CFL (up to 150W) and Incandescent/Halogen (up to 300W) bulbs.
- Single Pole Control: Designed for single-pole circuits only.
- Ibi Wiwa jakejado: 180° detection angle with a maximum range of 26 feet (8 meters).
- Ikole ti o tọ: Features a tough thermoplastic housing for impact and scratch resistance.
5. fifi sori
5.1 Akojọ aṣyn fifi sori ẹrọ tẹlẹ
- Rí i dájú pé agbára ti pa ní ẹ̀rọ ìdènà ìṣiṣẹ́ kí o tó bẹ̀rẹ̀.
- Confirm the presence of a neutral wire (typically white) in your electrical box. This switch requires a neutral wire.
- Verify that the circuit is a single-pole setup. This switch is not compatible with 3-way or multi-way circuits.
5.2 Awọn itọnisọna Wiring
Follow the wiring diagram carefully. If you are unsure about any steps, consult a qualified electrician.
- Pa a agbara ni Circuit fifọ.
- Yọ awọn ti wa tẹlẹ odi awo ati ki o yipada.
- Identify the wires: Hot (Black), Load (Red, or another color connected to the light), Neutral (White), and Ground (Green or bare copper).
- Connect the wires from the wall box to the corresponding terminals on the ECOELER Motion Sensor Light Switch as shown in the wiring diagram below.
- Secure the switch into the wall box with the provided screws.
- Attach the new wall plate.
- Mu pada agbara ni awọn Circuit fifọ.
- Allow a 30-second warm-up period after power is restored for the sensor to calibrate.
Figure 3: Wiring Diagram for Model YM2112.
| Circuit Box Wire | Screw on YM2112 Switch |
|---|---|
| Power wire (hot) | Dudu |
| Load to power light or fan | Wura |
| Green or non-insulated (copper) ground wire | Alawọ ewe |
| Neutral (required) | Fadaka |
Akiyesi: There is a 30-second warm-up period after each power reset. During this time, the sensor may not respond immediately.
6. Isẹ
The ECOELER Motion Sensor Light Switch offers three primary operation modes: Occupancy (OCC), Vacancy (VAC), and OFF. These modes are selected using the internal switches located behind the faceplate.
Figure 4: Operation Modes Diagram.
6.1 Occupancy (OCC) Mode
- Iṣẹ: Automatic ON and Automatic OFF.
- Iwa: The light automatically turns ON when motion is detected and automatically turns OFF after a set time delay when no motion is detected.
- Apẹrẹ fun: High-traffic areas where hands-free operation is desired, such as bathrooms, laundry rooms, and closets.
6.2 Vacancy (VAC) Mode
- Iṣẹ: Manual ON and Automatic OFF.
- Iwa: The light must be manually turned ON by pressing the ON/OFF button. It will then automatically turn OFF after a set time delay when no motion is detected.
- Apẹrẹ fun: Areas where you prefer to control when the light turns on, but still want the energy-saving benefit of automatic shut-off, such as offices or living rooms.
6.3 PA Ipo
- Iṣẹ: Manual ON and Manual OFF.
- Iwa: The light is controlled entirely manually by pressing the ON/OFF button. Motion detection is disabled for light activation, but the sensor may still detect motion (indicated by an LED flash) without triggering the light.
- Apẹrẹ fun: Situations where automatic control is not desired, or for testing purposes.
7. Àwọn Ètò Tí A Lè Ṣe Àtúnṣe
The ECOELER Motion Sensor Light Switch features adjustable settings for optimal performance. These settings are accessed by carefully removing the faceplate to reveal the adjustment dials and switches.
olusin 5: Ti abẹnu view of adjustable settings.
Nọmba 6: Alaye view of customizable settings.
7.1 Adjustable Sensitivity (SENSE)
- Ibiti: Low (20%) to High (100%).
- Iṣẹ: Controls how easily the sensor detects motion.
- Atunṣe: Turn the 'SENSE' dial to increase or decrease the detection range and responsiveness. Higher sensitivity detects smaller movements or movements further away.
7.2 Adjustable Light Level (LIGHT)
- Eto: Day, Dim, Dark.
- Iṣẹ: Determines the ambient light level at which the sensor will activate the lights.
- Atunṣe: Select 'Day' for activation regardless of ambient light, 'Dim' for activation in low light conditions (evening), and 'Dark' for activation only in very low light (night).
7.3 Adjustable Time Delay (TIME)
- Ibiti: 15 seconds, 1 minute, 5 minutes, 15 minutes, 30 minutes.
- Iṣẹ: Sets how long the light remains ON after the last detected motion.
- Atunṣe: Select the desired time delay using the 'TIME' dial.
8. Ibiti wiwa
The ECOELER Motion Sensor Light Switch utilizes Passive Infrared (PIR) technology to detect human body heat movement. It offers a wide detection area for effective coverage in various room layouts.
- Igun Wiwa: 180 iwọn.
- Ibiti o pọju: Up to 26 feet (approximately 8 meters) from the front, and up to 15 feet (approximately 4.5 meters) on the sides.
- Ibi: For optimal performance, install the switch in a location where its field of view is not obstructed by furniture, doors, or other objects.
Figure 7: Motion Detection Coverage Area.
9. Itọju
The ECOELER Motion Sensor Light Switch requires minimal maintenance. Follow these guidelines to ensure proper function and longevity:
- Ninu: Gently wipe the surface of the switch and sensor lens with a soft, dry cloth. Do not use abrasive cleaners, solvents, or excessive moisture, as these can damage the device.
- Awọn idilọwọ: Ensure the sensor lens is free from dust, dirt, or any obstructions that could interfere with motion detection.
- Awọn iṣayẹwo deede: Periodically test the switch's functionality to ensure it is operating correctly in your chosen mode and settings.
- Power Off for Service: Always turn off power at the circuit breaker before performing any maintenance that involves removing the wall plate or accessing internal components.
10. Laasigbotitusita
If you experience issues with your ECOELER Motion Sensor Light Switch, refer to the following common problems and solutions:
| Isoro | Owun to le Fa | Ojutu |
|---|---|---|
| Ìmọ́lẹ̀ kìí tan pẹ̀lú ìṣípo. | 1. Agbara wa ni pipa. 2. Ti ko tọ onirin. 3. Sensor lens obstructed. 4. Ifamọ ṣeto ju kekere. 5. Light level setting too high (e.g., 'Dark' in a bright room). 6. Switch is in VAC or OFF mode and not manually activated. | 1. Ṣayẹwo Circuit fifọ. 2. Verify wiring connections (refer to Section 5.2). Ensure neutral wire is connected. 3. Clear any obstructions from the sensor lens. 4. Increase sensitivity setting (refer to Section 7.1). 5. Adjust light level setting (refer to Section 7.2). 6. Switch to OCC mode or manually activate in VAC mode. |
| Light turns ON too frequently or unexpectedly. | 1. Ifamọ ṣeto ga ju. 2. Sensor detecting motion outside desired area (e.g., pets, drafts). 3. Switch is in OCC mode in a high-traffic area. | 1. Decrease sensitivity setting (refer to Section 7.1). 2. Reposition the switch or adjust sensitivity to narrow detection. 3. Consider switching to VAC mode if manual activation is preferred. |
| Light turns OFF too quickly or stays ON too long. | Eto idaduro akoko ko tọ. | Adjust the time delay setting to your preference (refer to Section 7.3). |
| Light flickers or does not work with certain bulbs. | Incompatibility with bulb type or wattage ti kọja. | Ensure bulbs are within specified wattage limits (LED/CFL up to 150W, Incandescent/Halogen up to 300W). Try a different type of compatible bulb. |
| Switch does not respond after power restoration. | Warm-up period not completed. | Allow 30 seconds for the sensor to warm up and calibrate after power is restored. |
11. Awọn pato
| Iwa | Ẹ̀kúnrẹ́rẹ́ |
|---|---|
| Nọmba awoṣe | YM2112 |
| Orisun agbara | Okun Itanna |
| Voltage | 120V AC, 60Hz |
| Ẹrù Tó Pọ̀ Jùlọ (LED/CFL) | 150W |
| Max Load (Incandescent/Halogen) | 300W |
| Iṣagbesori Iru | Ògiri Ògiri |
| Igun Awari | 180 iwọn |
| Ibiti o pọju | ẹsẹ 26 (mita 8) |
| Awọn iwọn otutu ti nṣiṣẹ | 32°F si 104°F (0°C si 40°C) |
| Awọn iwọn Ọja (D x W x H) | 115D x 40W x 68H millimeters (4.53 x 1.57 x 2.68 inches) |
| Iwọn Nkan | 0.15 iwon (68 giramu) |
| Ailopin Waya | Ti beere fun |
| Ilu isenbale | China |
12. Atilẹyin ọja
The ECOELER Motion Sensor Light Switch (Model YM2112) comes with a one-year warranty from the date of purchase. This warranty covers defects in materials and workmanship under normal use. For warranty claims or service, please contact ECOELER customer support.
13. Atilẹyin
For technical assistance, troubleshooting, or general inquiries regarding your ECOELER Motion Sensor Light Switch, please contact our support team:
- Imeeli: SUPPORTS@ECOELER.COM
- Olupese: ECOELER ELECTRIC INC