Ọrọ Iṣaaju
Thank you for choosing the Satco S12535 ST19 LED Light Bulb. This manual provides essential information for the safe and efficient use of your new LED bulb. Please read these instructions carefully before installation and retain them for future reference.
Image: The Satco S12535 ST19 LED Light Bulb, clear glass with visible filaments.
Alaye Aabo pataki
- Ewu ti Ina mọnamọna: Always disconnect power before installing or replacing the bulb.
- Abe ile/ita gbangba Lo: This bulb is rated for wet locations (IP65) and suitable for enclosed fixtures. It can be used indoors or in covered outdoor environments.
- Voltage: Rii daju pe imuduro voltage is 120V. Do not use with incompatible voltage.
- Dimming: This bulb is dimmable. Use only with compatible 120V dimmers. Incompatible dimmers may cause flickering or damage.
- Iwọn otutu: Do not operate outside the specified temperature range of -20°C to +45°C.
- Mimu: Allow the bulb to cool before handling. Avoid touching the bulb with bare hands immediately after use.
- Idasonu: Pa awọn gílóòbù LED rẹ́ ní ìbámu pẹ̀lú àwọn òfin agbègbè.
Eto ati fifi sori
- Agbara Pa: Before installation, ensure the power supply to the fixture is turned off at the circuit breaker or fuse box.
- Yọ Bulb atijọ kuro: Fara yọ boolubu ti o wa tẹlẹ kuro ni imuduro.
- Fi Bọlubu Tuntun sii: Screw the Satco S12535 LED bulb into the E26 medium base socket. Ensure it is securely tightened but do not overtighten.
- Agbara Tan: Mu agbara pada si imuduro.
- Dimmer Compatibility (if applicable): If using a dimmer, ensure it is compatible with LED bulbs and rated for 120V.
Image: Close-up of the E26 medium base of the Satco LED bulb, indicating its standard screw-in design.
Isẹ
The Satco S12535 LED bulb is designed for immediate illumination upon power activation. It provides 425 lumens of 5000K natural white light, suitable for various applications.
- Iṣakoso Imọlẹ: When connected to a compatible 120V dimmer, the brightness can be adjusted from full intensity to a lower, softer glow.
- Didara Imọlẹ: The bulb features a high Color Rendering Index (CRI) of 92, ensuring accurate and natural color representation of objects in its light.
- Tan tan kaakiri: A 300-degree beam spread provides wide and even illumination, minimizing shadows.
Image: The Satco ST19 LED bulb installed in a fixture, providing illumination to a modern living room and kitchen area.
Itoju
The Satco S12535 LED bulb requires minimal maintenance due to its long rated life of 15,000 hours.
- Ninu: Lati nu boolubu naa, rii daju pe agbara wa ni pipa ati pe boolubu naa dara. Pa rọra nu pẹlu asọ ti o gbẹ. Ma ṣe lo awọn olutọpa omi tabi awọn ohun elo abrasive.
- Rọpo: Replace the bulb when it reaches the end of its operational life. Follow the installation steps in reverse to remove the old bulb.
Laasigbotitusita
If you encounter issues with your Satco S12535 LED bulb, refer to the following common troubleshooting steps:
- Boolubu Ko tan:
- Rí i dájú pé agbára ìpèsè sí ẹ̀rọ náà wà nílẹ̀.
- Ṣayẹwo boya boolubu naa ba wa ni aabo.
- Ṣe idanwo boolubu naa ni imuduro iṣẹ miiran lati jẹrisi pe ko jẹ aṣiṣe.
- Verify the fixture itself is operational.
- Ìmọ́lẹ̀ tí ń tàn tàbí tí kò dúró ṣinṣin:
- If using a dimmer, ensure it is compatible with LED bulbs. Older incandescent-only dimmers may cause flickering.
- Check for loose connections in the fixture or bulb socket.
- Rii daju voltagIpese e duro ṣinṣin ni 120V.
- Bulb is Too Dim or Too Bright:
- If using a dimmer, adjust the dimmer setting.
- Confirm the bulb's specifications (425 lumens, 5000K) match your lighting requirements.
Awọn pato
| Ẹya ara ẹrọ | Ẹ̀kúnrẹ́rẹ́ |
|---|---|
| Nọmba awoṣe | S12535 |
| Wattage | 5 Wattis (Ojoba Osan 40W) |
| Imọlẹ | 425 Lumens |
| Iwọn otutu awọ | 5000K (funfun Adayeba) |
| Apẹrẹ boolubu | ST19 |
| Ipilẹ Iru | E26 Alabọde Mimọ |
| Atọka Rendering Awọ (CRI) | 92 |
| Igun tan ina | Awọn iwọn 300 |
| Voltage | 120V |
| Dimmable | Bẹ́ẹ̀ni (pẹ̀lú àwọn dimmers 120V tó báramu) |
| won won Life | Awọn wakati 15,000 |
| Ayika Rating | Wet Location Rated (IP65), Enclosed Fixture Rated |
| Awọn iwọn otutu ti nṣiṣẹ | -20°C si +45°C |
| Awọn iwe-ẹri | cULus, FCC, RoHS |
| Agbara ifosiwewe | 0.7 |
| Igbohunsafẹfẹ | 60Hz |
| Ìwúwo Nkan (pack6) | 1.06 iwon |
Image: Lighting Facts label detailing brightness, estimated yearly energy cost, life, light appearance (5000K), and energy used (5 watts).
Atilẹyin ọja ati Support
The Satco S12535 ST19 LED Light Bulb is backed by a 2-odun olupese ká atilẹyin ọja lati ọjọ ti o ra.
For warranty claims, technical assistance, or product support, please contact Satco customer service directly. Refer to the product packaging or the official Satco webAaye fun lọwọlọwọ alaye olubasọrọ.
Webojula: www.satco.com