Ọja Pariview
The SUNLU S1 Plus Filament Dryer Box is designed to maintain optimal filament conditions for 3D printing. It helps prevent common printing issues caused by moisture absorption in various filament types, ensuring higher print quality and reliability.
Package Awọn akoonu
- SUNLU S1 Plus Filament Dryer Unit
- Adapter agbara
- Itọsọna olumulo
- Filament Guide Tubes (small white gaskets)
Awọn ilana iṣeto
- Place the filament spool into the drying chamber. The dryer supports various spool sizes and filament diameters (1.75mm, 2.85mm, 3.00mm).
Image illustrating the compatibility of the SUNLU S1 Plus Filament Dryer with various filament spool sizes and diameters (1.75mm, 2.85mm, 3.00mm). - Select the appropriate filament outlet hole (top or front) based on your 3D printer's inlet position. Use the provided guide tubes if necessary.
- Connect the power adapter to the dryer and a power source.
Operating the Filament Dryer
The SUNLU S1 Plus features a 2-inch LCD screen and two control buttons for easy operation.
Titan / Paa
- To power on, press the Left or Right button.
- To power off, press both buttons simultaneously.
Eto iwọn otutu
- After powering on, press the Left or Right button to set the target temperature. The adjustable temperature range is 35°C to 55°C.
- Refer to the material-specific temperature guidelines in the manual for optimal drying.
Eto akoko
- Hold the Left button to enter time setting mode.
- Press Left or Right to adjust the drying duration (1-99 hours).
- Hold the Left button again to confirm and exit.
Ifihan ọriniinitutu
- Hold the Right button to display the current chamber humidity (%RH).
- Hold the Right button again to exit the humidity display.
Filament Compatibility and Recommended Settings
The dryer is compatible with a wide range of 3D printing filaments. Below are general recommended settings:
| Ohun elo | Baking Temp (°C) | Àkókò (h) |
|---|---|---|
| PLA | 45-50 | 3-6 |
| IGI | 45-50 | 3-6 |
| PVB | 45-50 | 3-6 |
| ABS | 50-55 | 3-6 |
| HIPS | 50-55 | 3-6 |
| PC | 50-55 | 3-6 |
| PA | 50-55 | 3-6 |
| ASA | 50-55 | 3-6 |
| PETG | 47-51 | 3-6 |
| TPU | 47-51 | 3-6 |
Akiyesi: The operating temperature range for this product is 20°C to 35°C. If the ambient temperature is below 10°C, it may fail to start normally, which is considered a normal occurrence.
Itoju
- Regularly inspect the filament path for any debris or blockages.
- Keep the dryer clean and free from dust to ensure optimal performance.
- Store the dryer in a dry environment when not in use.
Laasigbotitusita Awọn ọrọ to wọpọ
Poor Print Quality (Stringing, Blobs, Poor Adhesion)
- Nitori: Filament has absorbed moisture.
- Ojutu: Increase drying time or temperature within recommended ranges. Ensure filament is thoroughly dried before and during printing.
Togbe Ko Alapapo
- Nitori: Ambient temperature is too low (below 10°C).
- Ojutu: Operate the dryer in an environment within the recommended temperature range (20°C to 35°C).
Awọn pato ọja
- Iwọn ọja: 271 (L) x100 (W) x237 (H) mm
- Max Coil Size: Ø210*85(H)mm
- Apapọ iwuwo:980g
- Opin Iwọn: 1.75/2.85/3.0mm
- Ọriniinitutu ṣiṣẹ: ≤90%
- Awọn iwọn otutu ṣiṣẹ: 35°C-55°C
- Agbara titẹ sii: AC 100V-240V, 50/60HZ
- Agbara Ijade: DC 24V ± 1.2V, 2A
- Agbara imurasilẹ: 0.05W
- Max Working Electricity:1.8A
- Max Ṣiṣẹ Agbara: 48W
- Iwọn iboju LCD: 2 inch
Atilẹyin ọja ati Support
The product comes with a one-year warranty under normal operating conditions as described in this manual.
Atilẹyin ọja ko ni bo awọn bibajẹ to šẹlẹ nipasẹ lilo awọn kebulu agbara ti awọn oriṣiriṣi awọn pato tabi iṣẹ ti ko tọ gẹgẹbi fun awọn itọnisọna inu iwe afọwọkọ lakoko akoko atilẹyin ọja.
For after-sales service and support, please visit the official SUNLU webojula tabi kan si wọn support egbe.