1. Ifihan
The CADDXFPV Eclipse Thermal Camera is an advanced thermal imaging solution designed for various applications, including FPV (First Person View) drones. This manual provides essential information for the proper setup, operation, and maintenance of your thermal camera system. Please read this manual thoroughly before using the product to ensure safe and optimal performance.
2. Alaye Aabo
- Do not expose the camera to extreme temperatures, direct sunlight for prolonged periods, or corrosive environments.
- Yago fun sisọ silẹ tabi tẹriba ẹrọ si awọn ipa to lagbara.
- Rii daju pe voltage is supplied to the device as specified in the 'Specifications' section. Incorrect voltage le fa ibajẹ ayeraye.
- Pa ẹrọ naa kuro ninu omi ati ọrinrin.
- Do not attempt to disassemble or modify the camera system. This will void the warranty and may cause damage.
- Use only original or approved accessories.
3. irinše Loriview
The CADDXFPV Eclipse Thermal Camera system typically includes the following main components:
- Thermal Camera Module: The primary unit responsible for capturing thermal images.
- Main Processing Unit: Handles video processing, power management, and interfaces.
- Eriali: For video transmission (if applicable to your specific variant).
- Awọn kebulu asopọ: For power, video, and data transmission between modules.
4. Awọn pato
The following specifications apply to the Eclipse Camera-640HD model. Specifications may vary slightly for other variants (384, 256).
| Ẹya ara ẹrọ | Ẹ̀kúnrẹ́rẹ́ |
|---|---|
| Iru oluwari | Afẹfẹ vanadium ti ko tutu |
| Ipinnu | 256x192@12µm |
| Iwọn gigun | 8 ~ 14µm |
| NETD | ≤40mk @ F1 25°C |
| Lẹnsi | F1.0/4mm/50°(H)*37.2°(V)*62.3°(D) |
| Iwọn fireemu | 50 fps |
| Agbara agbara | <1.5w |
| Abajade | PAL |
| Ipese Voltage | 5v ~ 20v |
| Lẹnsi | 4mm |
| Awọn iwọn otutu ti nṣiṣẹ | -20°C ~60°C |
| Atọka Analog | CVBS |
| HD Interface | MIPI-CSI/Walksnail Avatar |
| Lairi | Apapọ Lairi 20ms |
| Didara Aworan | AI Image Enhancement |
| Ohun elo | Irin ti ko njepata |
| Controllable Distance | 200~800 (units not specified, typically meters for FPV) |
5. Eto ati Wiring
Carefully follow the wiring diagrams below to connect your CADDXFPV Eclipse Thermal Camera system. Incorrect wiring can damage the device and connected components.
5.1 UART Asopọ
This connection is typically used for data communication, such as OSD (On-Screen Display) control or flight controller integration.
| Pin | Išẹ |
|---|---|
| TX2 | UART Transmit 2 |
| RX2 | UART Receive 2 |
| GND | Ilẹ |
| 5V0 | 5V agbara wu |
5.2 Main Power and Video Output
This connection provides power to the unit and outputs the video signal. Ensure the power supply is within the specified voltage ibiti (9V-26V).
| Pin | Išẹ |
|---|---|
| CVBS | Afọwọṣe Video wu |
| Power 9V-26V | Main Power Input (9V to 26V) |
| GND | Ilẹ |
| OSD | Lori-iboju Iṣakoso Ifihan |
| V-BUS | Voltage Bus (Power Output) |
Akiyesi: Always double-check your wiring before applying power to prevent damage to the camera or other electronic components.
6. Awọn ilana Iṣiṣẹ
6.1 Agbara Lori
Once correctly wired, apply power within the specified voltage range (5V-20V for the camera module, 9V-26V for the main unit). The system should initialize, and thermal video output will be available via the CVBS (Analog) or MIPI-CSI/Walksnail Avatar (HD) interfaces.
6.2 Video wu
The camera outputs a PAL video signal. Ensure your display device or video receiver is compatible with PAL format. The HD interface supports MIPI-CSI and Walksnail Avatar systems for high-definition thermal video.
6.3 Àwòrán Gbígbóná
The camera utilizes an uncooled vanadium oxide detector to capture thermal radiation. The AI Image Enhancement feature helps improve the clarity and detail of the thermal feed. The latency is approximately 20ms, providing a responsive experience for FPV applications.
7. Itọju
- Ninu: Gently clean the camera lens and housing with a soft, dry, lint-free cloth. Do not use abrasive cleaners or solvents.
- Ibi ipamọ: Tọ́jú kámẹ́rà náà sí ibi tí ó tutù tí ó sì gbẹ, tí kò sí ìmọ́lẹ̀ oòrùn tààrà àti ooru tó le koko.
- Ayewo: Ṣayẹwo awọn kebulu ati awọn asopọ nigbagbogbo fun eyikeyi ami ti wọ tabi ibajẹ.
8. Laasigbotitusita
- Ko si Agbara: Check all power connections and ensure the supply voltage is within the specified range (9V-26V for the main unit). Verify that the power source is functioning correctly.
- Ko si Ijade fidio: Confirm that the video output cable (CVBS or HD interface) is securely connected to your display device or video receiver. Ensure your display is set to the correct input and supports PAL format for analog output.
- Didara Aworan Ko dara: Check for any obstructions on the camera lens. Ensure the camera is operating within its specified temperature range (-20°C to 60°C).
- Ifiranṣẹ Alailowaya: Inspect antenna connections for tightness and ensure they are not damaged. Check for potential interference sources in your operating environment.
9. Awọn imọran olumulo
- For optimal thermal performance, allow the camera a few moments to stabilize after powering on, especially in varying ambient temperatures.
- Experiment with different mounting positions on your drone or platform to find the best field of view and minimize vibrations.
- Keep the lens clean to ensure clear thermal imagery. Dust or smudges can significantly degrade performance.
- When using the HD interface, ensure your digital FPV system (e.g., Walksnail Avatar) is updated to the latest firmware for best compatibility and features.
10. Atilẹyin ọja ati Support
This product comes with a standard manufacturer's warranty. For specific warranty terms and conditions, please refer to the documentation provided at the time of purchase or contact your retailer. For technical support, please reach out to the CADDXFPV customer service channels.
11. Olubasọrọ Alaye
For further assistance or inquiries, please contact CADDXFPV customer support through their official webojula tabi awọn olupin ti a fun ni aṣẹ.
