Lithonia Lighting T21 BL Track Lighting End Feed Connector Instruction Manual

Ọrọ Iṣaaju

This manual provides essential instructions for the safe installation and proper use of the Lithonia Lighting T21 BL Track Lighting End Feed Connector. This connector is specifically designed to supply power to Juno Lighting Trac-Master track systems.

The T21 BL connector is constructed from extruded aluminum with a thermoplastic insulator, ensuring both durability and reliable electrical performance within your lighting setup.

Alaye Aabo

Jọ̀wọ́ ka gbogbo ìtọ́ni kí o sì lóye wọn kí o tó bẹ̀rẹ̀ sí í fi sori ẹ̀rọ. Àìtẹ̀lé àwọn ìtọ́ni wọ̀nyí lè fa ìkọlù iná mànàmáná, iná, tàbí àwọn ewu mìíràn.

• IKILO: Ewu ti ina-mọnamọna. Ge asopọ agbara ni fiusi tabi fifọ Circuit ṣaaju fifi sori ẹrọ tabi iṣẹ.
• Gbogbo asopọ ina gbọdọ wa ni ibamu pẹlu awọn koodu agbegbe, awọn ilana, tabi Koodu Ina Orilẹ-ede (NEC).
• Tí o kò bá mọ àwọn wáyà iná mànàmáná dáadáa, kan sí onímọ̀ nípa iná mànàmáná tó mọ̀ nípa wọn.
• Do not install in wet locations or areas exposed to direct water spray. This product is intended for indoor use only.
• Rii daju pe gbogbo awọn asopọ wa ni aabo ati idabobo daradara.

Package Awọn akoonu

Daju pe gbogbo awọn paati ti a ṣe akojọ si isalẹ wa ati ti ko bajẹ ṣaaju tẹsiwaju pẹlu fifi sori ẹrọ.

The image above displays the Lithonia Lighting T21 BL Track Lighting End Feed Connector and its associated components, including the main connector body, mounting bracket, threaded nipple, and lock nut.

• 1 x T21 BL End Feed Connector Body
• 1 x Atọka iṣagbesori
• 1 x Threaded Nipple
• 1 x Eso Titiipa
• 1 x Ground Screw

Eto ati fifi sori

Ṣaaju fifi sori ẹrọ

• Turn off power at the circuit breaker or fuse box before starting any electrical work.
• Rii daju pe ilẹ iṣagbesori jẹ mimọ, gbẹ, ati ohun igbekalẹ.
• Gather necessary tools: screwdriver, wire strippers, pliers, voltage idanwo.

Awọn Igbesẹ fifi sori ẹrọ

1. Prepare the Outlet Box: Ensure the electrical outlet box is properly installed and secured to the ceiling or wall.
2. So akọmọ iṣagbesori: Secure the provided mounting bracket to the outlet box using appropriate screws (not included, typically supplied with the outlet box).
3. Asopọmọra Waya: Feed the electrical wires from the outlet box through the center hole of the mounting bracket and into the connector body. Connect the supply wires to the corresponding wires on the T21 BL connector (typically black to black, white to white, and ground to ground). Use approved wire connectors.
4. Secure Connector Body: Position the T21 BL connector body over the mounting bracket. Use the threaded nipple and lock nut to firmly secure the connector to the mounting bracket and outlet box.
5. Connect to Track System: Align the end feed connector with the end of your Juno Lighting Trac-Master track section. Slide the connector firmly into the track until it clicks into place, ensuring a secure electrical and mechanical connection.
6. Pada Agbara pada: Once all connections are secure and the track system is fully assembled, restore power at the circuit breaker.

Akiyesi: For optimal safety and performance, it is recommended that installation be performed by a qualified electrician.

Awọn ilana Iṣiṣẹ

The Lithonia Lighting T21 BL End Feed Connector is designed for continuous operation once properly installed. It serves as the power supply point for your track lighting system.

• Ensure all track heads or fixtures are correctly inserted and locked into the track system.
• Verify that the circuit breaker supplying power to the track is in the 'ON' position.
• If using a dimmer switch, ensure it is compatible with your track lighting fixtures and is functioning correctly.

Itoju

The T21 BL connector requires minimal maintenance to ensure long-lasting performance.

• Ninu: Periodically wipe the exterior of the connector with a soft, dry cloth to remove dust and debris. Do not use abrasive cleaners or solvents.
• Ayewo: Annually inspect the connector and track system for any signs of damage, loose connections, or wear. If any issues are found, disconnect power and address them immediately.
• Do not attempt to disassemble or modify the connector. This will void the warranty and may create a safety hazard.

Laasigbotitusita

If you experience issues with your track lighting system, refer to the following common troubleshooting steps:

• No Power to Track:
  • Ṣàyẹ̀wò bóyá ẹ̀rọ ìdènà ẹ̀rọ náà ti bàjẹ́. Tún un ṣe tí ó bá pọndandan.
  • Ensure all wire connections at the outlet box and within the connector are secure.
  • Verify that the connector is fully seated and making proper contact with the track.
• Agbara Laarin:
  • Inspect for loose connections within the connector or where the connector meets the track.
  • Check for any damage to the track or connector that might be causing poor contact.
• Awọn imọlẹ didan:
  • Ensure all track heads are properly installed and making good contact.
  • Jẹrisi pe lapapọ wattage of your fixtures does not exceed the track system's capacity or the circuit's rating.

If troubleshooting steps do not resolve the issue, contact a qualified electrician or Lithonia Lighting customer support.

Awọn pato

Atilẹyin ọja

The Lithonia Lighting T21 BL Track Lighting End Feed Connector is backed by a 1-odun olupese atilẹyin ọja láti ọjọ́ tí a rà á. Àtìlẹ́yìn yìí bo àwọn àbùkù nínú àwọn ohun èlò àti iṣẹ́ ọwọ́ lábẹ́ lílo àti iṣẹ́ déédéé.

Please retain your proof of purchase for warranty claims. The warranty does not cover damage resulting from improper installation, misuse, abuse, or unauthorized modifications.

Atilẹyin

For technical assistance, replacement parts, or to inquire about warranty claims, please contact Lithonia Lighting customer support. Refer to the official Lithonia Lighting webaaye tabi apoti ọja fun alaye olubasọrọ lọwọlọwọ julọ.

When contacting support, please have your product model number (T21 BL) and proof of purchase readily available.