Ọrọ Iṣaaju
This manual provides instructions for the installation, operation, and maintenance of the Linear Multi-Code Keypad Transmitter, model 420001. This wireless keypad is designed for use with Multi-Code Receivers to control access to garage doors or gates.
Ọja Pariview
The Linear Multi-Code Keypad Transmitter 420001 is a 12-button alphanumeric keypad. It operates on a 300 MHz frequency and features 10 dip switches for programming. Its weatherproof casing ensures durability for outdoor use.
Aworan: Iwaju view of the Linear Multi-Code Keypad Transmitter 420001, showing the 12-button alphanumeric keypad and the "MULTI-CODE" branding at the top.
Eto ati fifi sori
Fifi sori batiri
The keypad requires one 9V alkaline battery (not included). To install:
- Open the keypad casing.
- Connect the 9V battery to the battery clip.
- Place the battery securely within the compartment.
- Close the keypad casing, ensuring it is sealed properly for weather resistance.
Iṣagbesori
The keypad is designed for screw-in installation and mounts with two screws.
- Choose a suitable location for mounting, ensuring it is within range of your Multi-Code Receiver.
- Mark the positions for the two mounting screws.
- Lu awaoko ihò ti o ba wulo.
- Secure the keypad to the surface using appropriate screws.
Siseto bọtini foonu
This keypad uses 10 dip switches for programming. The code is entered directly through the keypad, eliminating the need to manually adjust physical dip switches on the unit itself.
- Locate the dip switch settings on your Multi-Code Receiver or existing remote. This will be a sequence of 10 switches, each set to ON, OFF, or MIDDLE (if applicable).
- On the 420001 keypad, enter the 10-digit code corresponding to your receiver's dip switch settings. Refer to the keypad's internal instructions for specific key presses to represent ON, OFF, or MIDDLE positions.
- Press the "ACCESS" button to save the code.
- Test the keypad to ensure it operates your garage door or gate opener.
Akiyesi: Programming typically takes less than 2 minutes. Ensure the keypad is within operational range of the receiver during testing.
Awọn ilana Iṣiṣẹ
To operate your garage door or gate using the Linear Multi-Code Keypad Transmitter:
- Enter your programmed 10-digit access code using the alphanumeric buttons.
- Press the "ACCESS" button.
- The LED indicator will illuminate, and your Multi-Code Receiver should activate, opening or closing your garage door or gate.
If the door or gate does not respond, verify your code and ensure the keypad is within effective range of the receiver.
Itoju
- Rirọpo Batiri: When the keypad's performance degrades or the LED indicator fails to light, replace the 9V battery. Follow the battery installation steps.
- Ninu: Clean the keypad's exterior with a soft, damp asọ. Yago fun abrasive ose tabi epo.
- Atako oju ojo: The keypad features a weatherproof casing. Ensure the casing is properly closed and sealed after any internal access (e.g., battery replacement) to maintain its weather-resistant properties.
Laasigbotitusita
| Isoro | Owun to le Fa | Ojutu |
|---|---|---|
| Keypad does not respond or works intermittently. |
|
|
| Atọka LED ko tan imọlẹ. | Batiri ti ku tabi ti fi sori ẹrọ ti ko tọ. | Check battery connection or replace the 9V battery. |
| Keypad does not program correctly. | Incorrect dip switch settings entered. | Double-check the 10 dip switch settings from your receiver and re-enter the code carefully. |
Awọn pato
| Nọmba awoṣe | 420001 |
| Brand | Laini |
| Igbohunsafẹfẹ | 300 MHz |
| Number of Dip Switches | 10 |
| Orisun agbara | 1 x 9V Alkaline Battery (not included) |
| Iru fifi sori ẹrọ | Dabaru-Ni |
| Ọja Mefa | 6.75 x 1.5 x 3 inches |
| Iwọn Nkan | 4 iwon |
| Ohun elo | Ṣiṣu |
| Àwọ̀ | Alagara |
| Ibamu | FCC |
Atilẹyin ọja ati Support
Fun alaye atilẹyin ọja tabi atilẹyin imọ-ẹrọ, jọwọ tọka si osise olupese naa. webojula tabi kan si wọn onibara iṣẹ Eka. Tọju iwe-ẹri rira rẹ fun awọn ẹtọ atilẹyin ọja.
Olupese: Laini
