Ìwé Ìtọ́sọ́nà Olùlò Einhell BT-TJ 2250 Trolley Jack

1. Ifihan

This manual provides important information for the safe and proper operation, maintenance, and troubleshooting of your Einhell BT-TJ 2250 Trolley Jack. Please read this manual thoroughly before using the product and keep it for future reference.

The Einhell BT-TJ 2250 is a robust and stable trolley jack designed for lifting vehicles with a maximum load capacity of 2250 kg. It features two ball-bearing swivel castors for easy maneuverability, an extra-large support saddle, and a long, two-part lifting rod to ensure safe and easy lifting of loads. An integrated safety valve protects against overloading.

2. Awọn ilana aabo

Nigbagbogbo ṣe akiyesi awọn iṣọra ailewu atẹle lati yago fun ipalara tabi ibajẹ ọja naa:

• Ka iwe afọwọkọ naa: Before operation, read and understand all instructions and warnings in this manual.
• Agbara fifuye: Maṣe kọja agbara fifuye ti o pọju ti 2250 kg.
• Ilẹ Iduroṣinṣin: Always use the jack on a hard, level, and stable surface.
• Atilẹyin Ọkọ: After lifting, always support the vehicle with appropriate jack stands before working underneath it. Never rely solely on the jack for support.
• Ẹrù àárín: Ensure the load is centered on the saddle of the jack.
• Ko Agbegbe kuro: Keep hands, feet, and other body parts clear of moving parts and the area under the load.
• Itọju: Regularly inspect the jack for damage or wear. Do not use if damaged.
• Awọn ọmọde ati awọn ohun ọsin: Pa awọn ọmọde ati awọn ohun ọsin kuro ni agbegbe iṣẹ.
• Idaabobo Apọju: The jack is equipped with an overload safety valve. Do not attempt to bypass or adjust this valve.

3. Ọja irinše

Familiarize yourself with the parts of your Einhell BT-TJ 2250 Trolley Jack:

1. Ara akọkọ: The robust steel frame of the jack.
2. Apa gbigbe: The movable arm that raises the support saddle.
3. Support Saddle: The circular pad at the top of the lifting arm where the load rests. It is extra-large for stability.
4. Swivel Castors: Two ball-bearing wheels at the rear for easy steering and positioning.
5. Fixed Wheels: Two wheels at the front for stability.
6. Lifting Rod (Handle): A two-part rod used to pump the jack and operate the release valve.
7. Tu silẹ Valve: Located at the base of the lifting mechanism, controlled by rotating the lifting rod.
8. Overload Safety Valve: Internal mechanism to prevent lifting beyond the rated capacity.

4. Eto ati Apejọ

The Einhell BT-TJ 2250 Trolley Jack typically comes pre-assembled, but the lifting rod may need to be attached.

• Attach the Lifting Rod: Insert the two parts of the lifting rod together. Then, insert the assembled rod into the handle socket on the jack. Ensure it is securely seated.
• Bleed Air (First Use): Before first use, it is recommended to bleed any air from the hydraulic system.
  1. Turn the lifting rod counter-clockwise to fully open the release valve.
  2. Pump the lifting rod vigorously several times.
  3. Turn the lifting rod clockwise to close the release valve.

5. Awọn ilana Iṣiṣẹ

5.1. Gbigbe a Fifuye

1. Ṣeto Ọkọ naa: Dá ọkọ̀ náà sí orí ilẹ̀ líle tí ó tẹ́jú. Fi bírékì ìdúró ọkọ̀ náà sí i kí o sì dí àwọn kẹ̀kẹ́ tí yóò wà nílẹ̀.
2. Gbe Jack naa si: Locate the vehicle's designated lifting points (refer to your vehicle's owner's manual). Position the jack's support saddle directly under the lifting point.
3. Close the Release Valve: Turn the lifting rod clockwise until the release valve is fully closed. Do not overtighten.
4. Lift the Load: Pump the lifting rod up and down to raise the support saddle and lift the vehicle. Continue pumping until the vehicle reaches the desired height.
5. Ni aabo pẹlu Jack Stands: Immediately place appropriately rated jack stands under the vehicle's designated support points. Slowly lower the vehicle onto the jack stands by carefully turning the lifting rod counter-clockwise. Once the vehicle is securely resting on the jack stands, remove the trolley jack.

5.2. Sokale kan fifuye

If the vehicle is on jack stands, first lift it slightly off the stands using the trolley jack before lowering.

1. Pa Agbegbe naa kuro: Ensure no one is under or near the vehicle.
2. Gbe Jack naa si: If removed, reposition the jack's support saddle under the lifting point.
3. Laiyara Ṣii Tu silẹ Àtọwọdá: Slowly and carefully turn the lifting rod counter-clockwise to open the release valve. The vehicle will begin to descend. Control the descent speed by adjusting how much you open the valve.
4. Fully Lower: Continue lowering until the vehicle is fully on the ground.
5. Yọ Jack kuro: Once the vehicle is stable on the ground, remove the trolley jack.

6. Itọju ati Ipamọ

• Ninu: Clean the jack regularly with a damp asọ. Maṣe lo awọn kemikali lile.
• Lubrication: Periodically lubricate moving parts and pivot points with light machine oil.
• Epo eefun: Check the hydraulic oil level periodically. If low, refill with a high-quality hydraulic jack oil. Consult a qualified technician if unsure.
• Ayewo: Kí o tó lo gbogbo ìgbà, ṣe àyẹ̀wò jack náà fún àmì ìbàjẹ́, jíjò tàbí ìbàjẹ́. Má ṣe lo jack tí ó ti bàjẹ́.
• Ibi ipamọ: Store the jack in a dry, clean place, preferably with the ram fully retracted to protect the hydraulic cylinder.

7. Laasigbotitusita

8. Awọn pato

9. Atilẹyin ọja ati Support

For warranty information, please refer to the warranty card included with your product or visit the official Einhell website. For technical support or spare parts, please contact Einhell customer service. Keep your purchase receipt as proof of purchase.

Einhell Customer Service: Please refer to the contact details provided on the Einhell official webaaye tabi ninu apoti ọja rẹ.