Ọrọ Iṣaaju
The Samson PB15 Pro PowerBrite is a comprehensive rackmount power conditioner designed to provide clean, stable power to your audio equipment. It integrates power distribution, precise metering, and convenient lighting into a single 1U rack space unit. This manual provides essential information for the safe and efficient operation of your PowerBrite PB15 Pro.
Aworan: Iwaju view of the Samson PB15 Pro PowerBrite Rackmount Power Center, showing the main power switch, voltmeter, ammeter, dimmer control, pull-out lamps, and unswitched outlet.
Awọn Itọsọna Aabo
Please read and adhere to the following safety precautions to prevent damage to the unit or injury to yourself:
- Ma ṣe fi ẹrọ yii han si ojo tabi ọrinrin.
- Maṣe yọ ideri kuro. Ko si awọn ẹya ti olumulo-iṣẹ ninu. Tọkasi gbogbo iṣẹ si oṣiṣẹ oṣiṣẹ.
- Rii daju pe ẹyọ naa wa ni ilẹ daradara.
- Do not overload the power conditioner. Refer to the specifications for maximum current draw.
- Ge asopọ agbara ṣaaju ṣiṣe eyikeyi awọn asopọ tabi ṣiṣe itọju.
- Lo awọn pàtó voltage fun isẹ.
Ṣeto
Follow these steps to set up your PowerBrite PB15 Pro:
- Igbesoke agbeko: The PB15 Pro is designed for standard 19-inch equipment racks. Secure the unit using appropriate rack screws. Ensure adequate ventilation around the unit.
- Asopọ agbara: Connect the integrated AC power cord from the PB15 Pro to a suitable grounded wall outlet. Verify that the voltage matches the unit's requirements (115 VAC as indicated on the front panel).
- Asopọmọra Ẹrọ:
- Connect your audio or electronic equipment to the 8 switched AC outlets located on the rear panel of the PB15 Pro.
- An additional unswitched convenience outlet is located on the front panel for equipment that requires constant power, regardless of the main power switch status.
- Iṣakoso USB: Route all power cables neatly to prevent tripping hazards and ensure proper airflow.
Awọn ilana Iṣiṣẹ
Familiarize yourself with the controls and indicators on the front panel:
- Main Power Switch (OUTLETS ON/OFF): This large red rocker switch controls the power to the 8 rear-panel AC outlets. Flip it to the "ON" position to supply power to connected equipment. The front panel unswitched outlet remains active regardless of this switch's position.
- Voltmeter: The digital display labeled "VOLTMETER" shows the incoming AC line voltage, allowing you to monitor power conditions.
- Ammeter: The digital display labeled "AMMETER" indicates the total current (amperes) being drawn by all equipment connected to the switched outlets. This helps prevent overloading.
- Iṣakoso Dimmer: The blue knob labeled "DIMMER" adjusts the brightness of the two pull-out LED lamps.
- Pull-out LED Lamps: Two retractable LED lamps are located on the front panel. Pull them out to illuminate your rack equipment. Their brightness is controlled by the Dimmer knob.
- Unswitched Outlet (115 VAC): A single AC outlet on the front panel provides constant power, independent of the main power switch. Use this for equipment that needs to remain powered on.
- 15 AMP Circuit Breaker (PUSH TO RESET): Located on the left side of the front panel, this circuit breaker protects the unit from overloads. If the total current draw exceeds 15 amperes, the breaker will trip, cutting power to the switched outlets. To reset, push the button back in. Reduce the load before resetting.
Itoju
The Samson PB15 Pro PowerBrite requires minimal maintenance. Follow these guidelines to ensure its longevity:
- Ninu: Disconnect the unit from power before cleaning. Use a soft, dry cloth to wipe down the exterior. Do not use liquid cleaners or solvents.
- Afẹfẹ: Ensure that the ventilation slots are not obstructed. Proper airflow is crucial for preventing overheating.
- Ayẹwo USB: Periodically inspect the power cord and all connected cables for any signs of damage or wear. Replace damaged cables immediately.
Laasigbotitusita
If you encounter issues with your PowerBrite PB15 Pro, refer to the following common problems and solutions:
| Isoro | Owun to le Fa | Ojutu |
|---|---|---|
| No power to switched outlets. | Agbára yípadà pàtàkì ti pa. Ayika Circuit ti tripped. No incoming AC power. | Ensure the main power switch is ON. Ṣayẹwo 15 AMP circuit breaker and reset if tripped. Reduce connected load. Rí i dájú pé ihò ìta ògiri ní agbára. |
| LED lamps not illuminating. | Lamps not pulled out. Dimmer control set to minimum. | Fa LED lamps ni kikun. Rotate the Dimmer control clockwise to increase brightness. |
| Ammeter reading is high. | Excessive current draw from connected equipment. | Reduce the number of devices connected or use lower power consumption devices. Ensure total load does not exceed 15 Amperes. |
Awọn pato
| Ẹya ara ẹrọ | Ẹ̀kúnrẹ́rẹ́ |
|---|---|
| Ọja Mefa | 54.61 x 9.53 x 29.21 cm |
| Nọmba Awoṣe Nkan | SAM PB15PRO |
| Iwọn Nkan | 3.86 kg (3 kg 860 g) |
| Olupese | Samsoni |
| ASIN | B001B8ADV6 |
| Ọjọ Akọkọ Wa | Oṣu Kẹjọ Ọjọ 31, Ọdun 2012 |
| Orukọ Agbo | Awọn kondisona agbara |
| Awọn iÿë | 8 rear-panel switched AC outlets, 1 front-panel unswitched convenience outlet |
| Circuit fifọ | 15 Amperes, push to reset |
| Meta | Dual digital multi-meters (Voltmeter, Ammeter) |
| Itanna | Two pull-out LED lamps with dimmer control |
Atilẹyin ọja ati Support
Specific warranty information for the Samson PB15 Pro PowerBrite is not provided in this manual. For detailed warranty terms, technical support, or service inquiries, please contact Samson Technologies directly or refer to their official webojula. Tọju iwe-ẹri rira rẹ bi ẹri rira fun awọn iṣeduro atilẹyin ọja.
