Bostitch 21680B 80 Series Fine Wire Stapler Instruction Manual

1. Ọja Ipariview

The Bostitch 21680B is an air-powered fine wire stapler designed for various fastening applications. This tool is engineered for efficiency and durability, utilizing 80 series staples with a 1/2-inch crown and leg lengths ranging from 1/4 inch to 1/2 inch.

This manual provides essential information for the safe and effective operation, maintenance, and troubleshooting of your Bostitch 21680B stapler.

Image: The Bostitch 21680B Fine Wire Stapler, showcasing its yellow and black design and staple magazine.

2. Alaye Aabo

Always observe the following safety precautions when operating the Bostitch 21680B stapler to prevent injury and tool damage:

• Ka ati oye gbogbo awọn itọnisọna ṣaaju lilo ẹrọ naa.
• Wear appropriate personal protective equipment (PPE), including safety glasses with side shields, hearing protection, and gloves.
• Ensure the air compressor is set to the recommended operating pressure (refer to specifications). Do not exceed the maximum allowable pressure.
• Disconnect the air supply before loading staples, performing maintenance, clearing jams, or when the tool is not in use.
• Maṣe tọka ohun elo naa si ararẹ tabi awọn miiran.
• Keep hands and body parts clear of the discharge area.
• Use only the specified staples for this tool.
• Má ṣe lo ohun èlò náà bí ó bá bàjẹ́ tàbí tí kò bá ṣiṣẹ́ dáadáa.
• Jẹ ki agbegbe iṣẹ jẹ mimọ ati itanna daradara.

3. Awọn irinše

Familiarize yourself with the main components of your stapler:

• Nfa: Ó ń mú kí ẹ̀rọ ìdènà ṣiṣẹ́.
• Iwe irohin: Holds the strip of staples.
• Ibudo eefi: Releases compressed air.
• Afẹfẹ afẹfẹ: Oju opo asopọ fun okun afẹ́fẹ́.
• Contact Trip: Safety mechanism that must be pressed against the workpiece for the tool to fire.

4. Eto

4.1 Ìsopọ̀ mọ́ Ipèsè Afẹ́fẹ́

1. Rí i dájú pé a ti pa compressor afẹ́fẹ́ náà àti pé a ti fa omi kúrò nínú ojò afẹ́fẹ́ náà.
2. Attach a quick-connect fitting (not included) to the stapler's air inlet.
3. Connect the air hose from the compressor to the stapler's quick-connect fitting.
4. Set the air compressor regulator to the recommended operating pressure (typically 70-100 PSI, refer to tool specifications for exact range).
5. Tan konpireso afẹfẹ.

4.2 Fífi àwọn ìdìpọ̀ kún

1. Disconnect the air supply before loading staples.
2. Push the magazine latch or release button to open the staple magazine.
3. Insert a strip of 80 series staples into the magazine with the staple points facing down. Ensure the staples are correctly oriented.
4. Pa iwe irohin naa titi ti o fi há ni aabo.
5. So ipese afẹfẹ pada.

5. Awọn ilana Iṣiṣẹ

5.1 Ipilẹ isẹ

1. Ensure the stapler is properly loaded with staples and connected to the air supply.
2. Hold the stapler firmly with both hands.
3. Place the nose of the tool (contact trip) firmly against the workpiece where the staple is to be driven.
4. Squeeze the trigger to drive a staple.
5. Tu awọn okunfa ati ki o gbe awọn ọpa lati workpiece.

5.2 Depth Adjustment (If applicable)

Some models may feature a depth adjustment mechanism. If your model includes this feature, refer to the markings on the tool for adjusting staple depth. Rotate the adjustment dial or lever to achieve the desired staple penetration.

6. Itọju

Regular maintenance ensures optimal performance and extends the life of your stapler.

6.1 Daily Itọju

• Ge asopọ ipese afẹfẹ.
• Add 3-5 drops of pneumatic tool oil (not included) into the air inlet before each use.
• Wipe down the tool with a clean, dry cloth to remove dust and debris.
• Check all screws and fasteners for tightness. Tighten as necessary.

6.2 Air konpireso Itọju

Regularly drain moisture from your air compressor tank to prevent rust and ensure clean air supply to the tool.

6.3 Ibi ipamọ

Store the stapler in a clean, dry environment, disconnected from the air supply.

7. Laasigbotitusita

Lati nu jam kuro: Ge asopọ afẹfẹ. Open the magazine and carefully remove any jammed staples or debris. Do not force staples out. Reconnect air supply and test.

8. Awọn pato

• Awoṣe: 21680B
• Staple Series: 80 jara
• Crown Size: 1/2 inch
• Gigun Ẹsẹ: 1/4 inch to 1/2 inch
• Orisun Agbara: Agbara afẹfẹ
• Agbara Iṣiṣẹ: Typically 70-100 PSI (consult tool for exact range)
• Agbara Iwe irohin: Full Strip (approximately 156 fasteners)
• Ìwọ̀n Nkan: 2.15 iwon
• Ohun elo: Irin
• Àwọ̀: Yellow
• Awọn eroja to wa: Awọn asomọ
• Olupese: Stanley Bostitch

9. Atilẹyin ọja ati Support

For warranty information, technical support, or service inquiries, please refer to the official Bostitch webojula tabi kan si wọn onibara iṣẹ Eka. Tọju iwe-ẹri rira rẹ bi ẹri rira fun awọn iṣeduro atilẹyin ọja.