Ìwé Ìtọ́sọ́nà Olùlò Ètò Ìṣàkóso Rédíò Futaba FC-18 35 MHz

1. Ifihan

This manual provides detailed instructions for the proper setup, operation, and maintenance of your Futaba FC-18 35 MHz radio control system. Please read this manual thoroughly before using the system to ensure safe and efficient operation. The Futaba FC-18 is a versatile transmitter designed for various radio-controlled models, offering both PCM and PPM selectable modes for broad compatibility.

2. Awọn iṣọra aabo

• Always ensure the transmitter batteries are fully charged before operation.
• Never operate your radio control system in adverse weather conditions, such as rain, strong winds, or lightning.
• Always perform a range check before each flight or operation session.
• Ensure the correct frequency crystal is installed in both the transmitter and receiver.
• Keep the transmitter away from direct sunlight, high temperatures, and excessive moisture.
• Do not attempt to modify the transmitter's internal components. Refer all repairs to qualified service personnel.

3. Ọja Ipariview

The Futaba FC-18 35 MHz transmitter is equipped with a range of controls and features for precise model control. Below is an overview of its main components:

Figure 3.1: Futaba FC-18 35 MHz Transmitter Front View
This image displays the front panel of the Futaba FC-18 transmitter. Key features visible include the dual joysticks for primary control, various switches (D/R, ON/OFF), linear sliders, a multi-information text display, and control buttons for menu navigation and data input. The antenna extends from the top center. The 'Futaba' and 'FC-18 CAMPac System' branding are clearly visible.

• Joysticks: Two primary control sticks for pitch, roll, yaw, and throttle.
• D/R Switches: Dual Rate switches (labeled D/R) to adjust control sensitivity.
• ON/PA Yipada: Main power switch for the transmitter.
• Linear Sliders: Two sliders (labeled 'Mager' and 'Fetter' with 'LINEAR' below them) for fine-tuning specific functions, often used for mixing or auxiliary channels.
• Multi-Information Text Display: A liquid crystal display (LCD) providing real-time information, menu options, and system settings.
• Awọn bọtini Iṣakoso: A set of buttons (1, 2+, 3 SET, 4, MODE, DATA, CURSOR, 5, 6-, 7 CLR, ENT) used for navigating menus, entering data, and confirming selections.
• Agbara Yi pada: A dedicated switch for turning the unit on and off.
• PCM/PPM Selectable: The system supports both Pulse Code Modulation (PCM) and Pulse Position Modulation (PPM) modes, offering flexibility for different receivers.

4. Eto

Before operating your Futaba FC-18, follow these essential setup steps:

1. Fifi sori batiri: Open the battery compartment on the back of the transmitter and insert the required batteries, observing correct polarity. Ensure the battery pack is securely connected.
2. Itẹsiwaju Antenna: Fully extend the transmitter antenna before turning on the power.
3. Frequency Crystal: Verify that the 35 MHz frequency crystal in the transmitter matches the crystal in your receiver.
4. Mode Selection (PCM/PPM): Access the system menu via the Multi-Information Text Display and select either PCM or PPM mode according to your receiver's requirements. Refer to your receiver's manual for its compatible mode.
5. Receiver and Servo Connection: Connect your receiver to the model's power source and servos according to your model's instructions.
6. Agbara Ibẹrẹ Tan: Turn on the transmitter first, then the receiver. When powering off, turn off the receiver first, then the transmitter.

5. Ṣiṣẹ

Operating the Futaba FC-18 involves understanding its controls and menu system:

• Iṣakoso ipilẹ: Use the left joystick for throttle and rudder control, and the right joystick for elevator and aileron control (standard Mode 2 configuration).
• Dual Rates (D/R): Flip the D/R switches to instantly change the sensitivity of the corresponding control surfaces. This is useful for switching between precise control and aggressive maneuvers.
• Linear Sliders: Adjust the 'Mager' and 'Fetter' linear sliders to fine-tune auxiliary functions or mixing ratios as programmed in the system.
• Lilọ kiri akojọ aṣayan:
  • Tẹ awọn MODE button to cycle through main menu categories.
  • Lo awọn 1 ati 5 buttons (up/down arrows) to navigate within menus.
  • Lo awọn 2+ ati 6- buttons to adjust data values.
  • Awọn IGÚN button (4) moves the cursor for text input or selection.
  • Tẹ ENT to confirm a selection or enter a value.
  • Tẹ CLR (7) to clear an entry or go back to the previous screen.
  • Awọn 3 SET button is used for setting specific parameters.
• Iranti Awoṣe: The FC-18 features model memory to store settings for multiple models. Use the menu to select, save, and load model profiles.

6. Itọju

Proper maintenance ensures the longevity and reliability of your Futaba FC-18:

• Ninu: Wipe the transmitter's exterior with a soft, dry cloth. Do not use solvents or abrasive cleaners.
• Itọju Batiri: Remove batteries if the transmitter will not be used for an extended period. Store batteries in a cool, dry place.
• Ibi ipamọ: Store the transmitter in a protective case to prevent damage from impacts or dust. Avoid storing in extreme temperatures.
• Ayewo Antenna: Regularly check the antenna for any signs of damage or bending.

7. Laasigbotitusita

If you encounter issues with your Futaba FC-18, consider the following common problems and solutions:

8. Awọn pato

Key specifications for the Futaba FC-18 35 MHz radio control system:

• Nọmba awoṣe: FC-18
• Awoṣe: FC-18
• Batteries Necessary: No (refers to included batteries, user must provide)
• Awọn batiri To wa: Rara
• ASIN: B004MASAF6
• First Available on Amazon.de: Oṣu Kẹta Ọjọ 4, Ọdun 2011

9. Atilẹyin ọja ati Support

For warranty information, technical support, or service inquiries regarding your Futaba FC-18 radio control system, please refer to the official Futaba website or contact your authorized Futaba dealer. Specific warranty terms and support contact details are typically provided with the product packaging or on the manufacturer's official resources.