Ọja Pariview
The DIG PRV075 is a pipe thread adjustable pressure regulator designed to reduce and regulate incoming water pressure for drip irrigation and micro-sprinkler systems. It ensures the system operates within the appropriate pressure range, typically between 28 PSI and 60 PSI, providing consistent outlet pressure regardless of upstream fluctuations.
Aworan: Iwaju view of the DIG PRV075 Adjustable Drip Pressure Regulator, showing its black plastic body and red adjustment cap.
Awọn ẹya pataki:
- Adjustable pressure range with a single screw for fine-tuning.
- Rolling diaphragm design prevents debris from entering the spring assembly, ensuring longevity.
- Maintains reliable control of outlet pressure despite variations in incoming pressure or flow.
- Equipped with 3/4" female pipe thread (FPT) inlet and outlet for compatibility with standard connections.
Eto ati fifi sori
Proper installation is crucial for the optimal performance of your DIG PRV075 pressure regulator. Follow these steps carefully:
- Ṣe idanimọ Awọn aaye Asopọmọra: The PRV075 has 3/4" female pipe threads on both the inlet and outlet. Ensure your irrigation system components have compatible male pipe threads.
- Mura Asopọ naa: Turn off the main water supply to the irrigation line where the regulator will be installed.
- Thread the Regulator:
- Apply thread sealant tape (Teflon tape) or pipe dope to the male threads of your water source connection.
- Carefully thread the inlet side of the PRV075 onto the prepared male thread. Hand-tighten first, then use a wrench for an additional 1 to 2 turns until snug. Do not overtighten.
- Repeat the process for the outlet side, connecting it to your drip irrigation or micro-sprinkler system.
- Ṣayẹwo fun Leaks: Slowly turn on the main water supply and inspect all connections for leaks. Tighten any leaking connections gently.
Aworan: Apa view of the DIG PRV075 Pressure Regulator held in a hand, illustrating its compact size and showing approximate dimensions of 5.1 inches (12 cm) in length.
Awọn ilana Iṣiṣẹ
The DIG PRV075 is designed for easy pressure adjustment. Follow these steps to set the desired operating pressure:
- Wa skru Atunṣe: The pressure adjustment screw is located under the red cap at one end of the regulator. Gently pry off the red cap to expose the screw.
- Ṣatunṣe Ipa:
- Use a flathead screwdriver to turn the adjustment screw.
- Turning the screw aago yio pọ si the outlet pressure.
- Turning the screw counter-clockwise yio dinku the outlet pressure.
- Make small adjustments and observe the system's performance. For precise adjustment, use a pressure gauge downstream of the regulator.
- Ibi iṣẹ: The regulator is designed to operate within a range of 28 PSI to 60 PSI. Do not attempt to adjust outside this range.
- Rọpo fila: Once the desired pressure is set, securely replace the red protective cap.
Itoju
The DIG PRV075 is designed for minimal maintenance. However, periodic checks can ensure its long-term performance:
- Ṣayẹwo fun awọn n jo: Periodically check all connections for any signs of water leaks. Address any leaks promptly by tightening connections or replacing thread sealant.
- Ṣayẹwo fun idoti: While the rolling diaphragm helps prevent debris, if you notice inconsistent pressure or reduced flow, it may indicate debris accumulation. Turn off the water, disconnect the regulator, and inspect the inlet and outlet for any blockages. Clean gently with water if necessary.
- Igba otutu: In regions subject to freezing temperatures, it is recommended to drain the irrigation system, including the pressure regulator, to prevent damage from freezing water.
Laasigbotitusita
| Isoro | Owun to le Fa | Ojutu |
|---|---|---|
| No water flow or very low flow |
|
|
| Pressure too high or too low (and cannot be adjusted) |
|
|
| Omi n jo lati awọn asopọ |
|
|
Awọn pato
- Awoṣe: PRV075
- Brand: DIG
- Ohun elo: Plastic body, Stainless Steel exterior finish (referring to internal spring/components)
- Asopọ-wọle/Igbajade: 3/4" Female Pipe Thread (FPT)
- Ibiti Ipa Ti Atunṣe: 28 PSI si 60 PSI
- Awọn iwọn (L x W x H): Isunmọ 4 x 2 x 3 inches
- Ìwọ̀n Nkan: Isunmọ 1.6 iwon
- Nọmba Awọn ibudo: 2
- Iru Valve: Globe Valve (as per specification, though it's a regulator)
- UPC: 013158333333
Atilẹyin ọja ati Support
For information regarding product warranty, technical support, or replacement parts, please contact DIG customer service directly. Refer to the official DIG webAaye tabi apoti ọja fun awọn alaye olubasọrọ ti o wa lọwọlọwọ ati awọn ofin atilẹyin ọja.
You can visit the official DIG store for more information: DIG Official Store
