Ọrọ Iṣaaju
This manual provides essential information for the proper installation, operation, and maintenance of the Jackson 4730-111-60-41 Plug, Rinse Arm Stainless Steel. This genuine OEM replacement part is designed for commercial dish machines manufactured by Jackson, ensuring safety, reliability, and optimal performance. Please read this manual thoroughly before attempting any installation or maintenance.
Ọja Pariview
Figure 1: Jackson 4730-111-60-41 Plug, Rinse Arm Stainless Steel.
This image displays the Jackson 4730-111-60-41 Plug, a stainless steel component designed for rinse arms. The plug features a flat top with a single slot for installation using a flathead tool, and a threaded base for secure fitting. Its metallic surface shows a brushed finish, indicative of its durable stainless steel construction.
The Jackson 4730-111-60-41 is a critical component for the rinse arm assembly in Jackson commercial dish machines. It is manufactured from durable stainless steel, ensuring longevity and resistance to corrosion in demanding commercial kitchen environments.
Eto ati fifi sori
This plug is a replacement part. Ensure the dish machine is powered off and disconnected from the power source before beginning installation.
- Aabo Lakọkọ: Disconnect the dish machine from all power sources and water supply lines. Allow the machine to cool if it has been recently in operation.
- Access Rinse Arm: Locate the rinse arm assembly where the plug needs to be replaced. This may require opening access panels or removing other components. Refer to your specific dish machine's service manual for detailed access instructions.
- Remove Old Plug: Carefully unscrew or remove the existing plug from the rinse arm. Be prepared for any residual water to drain.
- Aye Ayewo: Clean the threaded opening or seating area where the new plug will be installed. Ensure there are no debris or old gasket material that could prevent a proper seal.
- Install New Plug: Insert the Jackson 4730-111-60-41 plug into the designated opening. Hand-tighten first to ensure proper threading.
- Secure Tightening: Using an appropriate flathead screwdriver or tool, gently tighten the plug until it is snug. Maṣe ṣe apọju, as this can damage the plug or the rinse arm assembly.
- Ṣe atunto: Reassemble any components or access panels that were removed.
- Idanwo: Reconnect power and water supply. Run a test cycle to check for leaks around the newly installed plug.
Awọn ilana Iṣiṣẹ
As a static component, the Jackson 4730-111-60-41 Plug does not have active operational controls. Its function is passive, ensuring proper sealing and flow within the rinse arm system. Once correctly installed, it operates as an integral part of the dish machine's rinse cycle.
- Ensure the plug is always securely seated before operating the dish machine.
- Regularly inspect the plug during routine maintenance checks to confirm it remains tight and free from damage.
Itoju
Proper maintenance extends the life of the plug and ensures optimal performance of your dish machine.
- Ayẹwo igbagbogbo: Periodically inspect the plug for signs of wear, corrosion, or damage. Check for any looseness or leaks around its seating area.
- Ninu: If accessible, clean the plug and its surrounding area during routine dish machine cleaning to prevent buildup of food particles or mineral deposits. Use mild detergents and avoid abrasive cleaners that could damage the stainless steel finish.
- Rọpo: If the plug shows significant wear, damage, or if leaks persist after tightening, replace it with a new genuine Jackson 4730-111-60-41 part.
Laasigbotitusita
| Isoro | Owun to le Fa | Ojutu |
|---|---|---|
| Water Leakage around Plug |
|
|
| Plug difficult to install/remove |
|
|
Awọn pato
- Nọmba awoṣe: 4730-111-60-41
- Brand: Jackson
- Ohun elo: Irin ti ko njepata
- Awọn iwọn ọja: 0.4 x 0.45 x 0.5 inches (0.32 ounces)
- Awọn iwọn idii: 5.0" (L) x 6.0" (W) x 9.0" (H)
- Ìwọ̀n Nkan: 9.07 g (0.32 iwon)
- Ilu isenbale: Orilẹ Amẹrika
- UPC: 046843132386
- Akọkọ Wa: Oṣu Karun ọjọ 16, Ọdun 2017
Atilẹyin ọja ati Support
As a genuine OEM replacement part, the Jackson 4730-111-60-41 Plug is manufactured to high standards by Jackson, a reputable manufacturer of commercial dish machines. For specific warranty information regarding replacement parts, please refer to the warranty documentation provided with your original Jackson dish machine or contact Jackson customer support directly.
For technical assistance, part inquiries, or support, please visit the official Jackson website or contact their customer service department. Using genuine OEM parts ensures compatibility and maintains the integrity of your equipment's warranty.
Jackson Official Webojula: Visit the Jackson Store on Amazon (Link provided for reference, actual official website may vary)
