Ìtọ́sọ́nà Olùlò Hanna Instruments Groline Taara Olùdánwò Ìhùwàsí Ilẹ̀ HI98331

1. Ifihan

This manual provides essential instructions for the proper use and maintenance of your Hanna Instruments Groline Soil Test Direct Soil Conductivity Tester, model HI98331. Please read this manual thoroughly before operating the device to ensure accurate measurements and prolong the life of your instrument.

Figure 1: Hanna Instruments Groline Soil Test Direct Soil Conductivity Tester HI98331. This image shows the complete device, featuring a digital display and a long, slender probe for direct soil insertion.

2. Alaye Aabo

Always handle the instrument with care. Do not immerse the meter body in water. Keep the battery compartment dry. Store the device in a cool, dry place when not in use.

3. Ọja irinše

The HI98331 Groline Soil Test Direct Soil Conductivity Tester includes:

• HI98331 Meter with integrated soil probe
• Awọn batiri CR2 (ti a ti fi sii tẹlẹ)
• Ilana itọnisọna

Figure 2: Battery compartment. This image shows the rear of the meter with the battery cover removed, revealing the CR2 battery slot.

4. Eto ati Batiri sori

The HI98331 meter comes with batteries pre-installed. If replacement is necessary:

1. Wa ideri ibi ipamọ batiri naa ni ẹhin mita naa.
2. Twist the cover counter-clockwise to remove it.
3. Remove the old CR2 battery and insert a new one, observing polarity.
4. Rọpo ideri kompaktimeti batiri ki o si yi lọna aago lati ni aabo.

Ensure the battery compartment is sealed tightly to prevent moisture ingress.

5. Awọn ilana Iṣiṣẹ

Follow these steps for accurate bulk EC measurement using your HI98331 Direct Soil EC Meter:

1. Prepare the Testing Location: Select the specific area in the soil where you wish to take a measurement.
2. Mọ Iwadii naa: Rinse the testing probe thoroughly with deionized water. Gently wipe it dry with a clean, soft cloth.
3. Moisten the Soil: Ensure the soil in the testing area is adequately moist. Dry soil will not yield accurate readings.
4. Create an Insertion Hole: Use a ruler or an auger to create a pilot hole in the soil. This helps maintain consistent testing depth and prevents damage to the probe.
5. Insert the Tester: Carefully insert the HI98331 soil conductivity tester directly into the prepared hole in the soil. Ensure good contact between the probe and the soil.
6. Ṣe Iwọnwọn: Wait for the reading on the digital display to stabilize. Record the displayed EC value.

Figure 3: Meter in operation. This image depicts the HI98331 meter with its probe inserted into soil, displaying a reading on its screen.

6. Iṣatunṣe

For optimal accuracy, regular calibration of your HI98331 is recommended. Refer to the specific calibration instructions provided in the full product manual or on the manufacturer's website. Typically, calibration involves using standard EC solutions.

7. Itọju ati Ipamọ

• Ṣiṣayẹwo Iwadii: After each use, rinse the probe with deionized water to remove any soil residue. Do not use abrasive materials.
• Ibi ipamọ: Store the meter in a clean, dry environment. Ensure the probe is clean and dry before storage.
• Igbesi aye batiri: Rọpo awọn batiri nigbati itọka batiri kekere ba han loju iboju.

8. Laasigbotitusita

9. Awọn pato

10. Atilẹyin ọja ati Support

For warranty information and technical support, please refer to the official Hanna Instruments webojula tabi kan si wọn onibara iṣẹ taara. Tọju iwe-ẹri rira rẹ bi ẹri rira.

Olupese: Hanna Instruments

Webojula: www.hannainst.com