Salter Labs 350 Cc Bubble Humidifier Instruction Manual

Ọja Pariview

The Salter Labs 350 Cc Bubble Humidifier is designed to provide humidification for oxygen therapy. It features 360-degree rectangular diffuser ports for quiet operation and low system back pressure. The dome lid design ensures high performance and rugged durability. These disposable humidifiers are intended for single-patient use, offering dependable and cost-effective performance.

Awọn ẹya pataki:

• 360° molded, low resistance, high output diffuser head design
• Connecting tower design
• Large, quad wing nut connector
• Easy seal, translucent, double helix thread jar
• Jar permanently etched with large print minimum/maximum water level markings

Image: Salter Labs 350 Cc Bubble Humidifier, showing the assembled unit with its clear jar and black dome lid.

Awọn ilana iṣeto

Ṣiṣi silẹ

Carefully remove the humidifier from its packaging. Inspect all components for any signs of damage. Do not use if any part is damaged.

Àgbáye ọriniinitutu

1. Unscrew the dome lid from the clear jar by turning it counter-clockwise.
2. Fill the jar with distilled water up to the maximum fill line indicated on the jar. Do not overfill.
3. Re-attach the dome lid securely by turning it clockwise until a tight seal is achieved.

Awọn ilana Iṣiṣẹ

Connecting to Oxygen Source

1. Connect the humidifier to your oxygen concentrator or flowmeter using the appropriate oxygen tubing.
2. Ensure all connections are secure to prevent any air or water leaks.

Monitoring Water Level

Regularly check the water level in the humidifier jar. Refill with distilled water as needed, ensuring it remains between the minimum and maximum fill lines to maintain proper humidification and prevent damage.

Iṣatunṣe Oṣuwọn sisan

Adjust the oxygen flow rate according to your healthcare provider's instructions. The humidifier is designed for quiet operation with low system back pressure, ensuring efficient humidification at prescribed flow rates.

Itoju

Daily Cleaning

1. Disconnect the humidifier from the oxygen source.
2. Disassemble the lid and jar.
3. Wash both parts with warm, soapy water.
4. Fi omi ṣan daradara pẹlu omi mimọ.
5. Jẹ́ kí afẹ́fẹ́ gbẹ pátápátá kí o tó tún kó o jọ.

Disinfection (Weekly)

For weekly disinfection, soak the disassembled parts in a solution of one part white vinegar to three parts water for 30 minutes. Rinse thoroughly with sterile water and allow to air dry completely before reassembly.

Rirọpo

This is a disposable humidifier designed for single-patient use. Replace the humidifier according to your healthcare provider's recommendations or if it shows signs of wear or damage, such as cracks or persistent leaks.

Laasigbotitusita

No Bubbling or Low Humidification

• Ṣayẹwo Ipele Omi: Rii daju pe ipele omi wa laarin awọn laini kikun ti o kere julọ ati ti o pọju.
• Ṣayẹwo Awọn isopọ: Verify all tubing connections are secure and there are no leaks.
• Inspect Diffuser: Ensure the diffuser ports are not clogged. Clean if necessary following maintenance instructions.

Ariwo Pupọ

• Ṣayẹwo Ipele Omi: Overfilling the jar can cause excessive noise. Adjust water level if needed.
• Ṣayẹwo fun ibajẹ: Check the lid and jar for cracks or damage that might affect the seal.

Omi jijo

• Tighten Lid: Ensure the dome lid is securely tightened onto the jar.
• Ṣayẹwo fun awọn dojuijako: Inspect the jar and lid for any cracks or damage. Replace the unit if damaged.

Awọn pato

Atilẹyin ọja ati Support

For warranty information or technical support regarding your Salter Labs 350 Cc Bubble Humidifier, please contact Salter Labs directly. Refer to the product packaging or the official Salter Labs webAaye fun awọn alaye olubasọrọ lọwọlọwọ julọ ati awọn ofin atilẹyin ọja.

Olupese: Salter Labs