1. Ọja Ipariview
The BriskHeat DHCS13 is a standard heavy-duty drum heater designed for metal drums and pails, specifically fitting 30-gallon (114L) containers. This heater provides efficient and uniform heating for various materials, utilizing a robust construction for durability and safety.
Its design incorporates a patented 360-degree grounded multi-stranded heating element, laminated between two extra-thick layers of 20mil fiberglass-reinforced silicone rubber. This construction ensures excellent strength, durability, and uniform heat distribution, meeting NEC 427.23 standards. The unit is moisture and chemical resistant and features an adjustable thermostat for precise temperature control.
Image 1.1: The BriskHeat DHCS13 drum heater shown installed on a black 30-gallon metal drum. The orange heating bands are visible wrapped around the drum, secured by spring closures.
2. Alaye Aabo
Read all instructions carefully before installation and operation. Failure to follow these instructions may result in property damage, serious injury, or death.
- Ensure the heater is used only on metal drums and pails as specified. Do not use on plastic drums.
- Daju pe awọn ipese agbara voltage matches the heater's requirements (120VAC).
- Always ensure the heater is properly grounded. The unit includes a standard 3-prong plug (NEMA 5-15) for this purpose.
- Do not operate the heater in explosive atmospheres or near flammable vapors unless specifically rated for such environments. This heater is not intrinsically safe.
- Avoid direct contact with the heating surface during operation, as temperatures can reach up to 450°F (232°C).
- Do not immerse the heater in liquid. It is moisture and chemical resistant, but not submersible.
- Ge asopọ agbara ṣaaju ṣiṣe eyikeyi itọju tabi awọn atunṣe.
- Jeki okun agbara kuro lati awọn aaye ti o gbona ati awọn egbegbe to mu.
- Do not modify the heater or its components. Use only genuine BriskHeat replacement parts if necessary.
3. Unpacking ati Awọn akoonu
Carefully unpack the BriskHeat DHCS13 drum heater from its packaging. Inspect the unit for any signs of shipping damage. If damage is observed, do not proceed with installation and contact your supplier immediately.
Awọn akoonu idii:
- BriskHeat DHCS13 Drum Heater (1 unit)
4. Eto ati fifi sori
The DHCS13 drum heater is designed for easy installation on 30-gallon metal drums.
- Prepare the Drum: Ensure the metal drum is clean and free from any debris or flammable residues on its exterior surface where the heater will be applied.
- Gbe ẹrọ ti ngbona: Wrap the DHCS13 drum heater around the circumference of the 30-gallon metal drum. Position it at the desired height, typically around the lower or middle section of the drum, depending on the material to be heated.
- Secure the Heater: The heater features a spring closure mechanism. Expand the spring closure as needed (up to 3 inches / 76mm) to securely fasten the heater around the drum. Ensure the heater fits snugly against the drum surface for optimal heat transfer.
- So agbara: Plug the 6ft (1.8m) long power cord with its standard 3-prong plug (NEMA 5-15) into a properly grounded 120VAC electrical outlet. Ensure the outlet is capable of supplying 1000 watts.
- Ṣayẹwo akọkọ: Before setting the temperature, ensure the heater is firmly attached and the power cord is not pinched or in contact with any hot surfaces.
5. Awọn ilana Iṣiṣẹ
The DHCS13 drum heater is equipped with an adjustable thermostat for precise temperature control.
- Ṣatunṣe iwọn otutu: Locate the adjustable thermostat dial on the heater. The thermostat has a temperature range of 50°F to 425°F (10°C to 218°C).
- Ṣeto iwọn otutu ti o fẹ: Rotate the dial to set the desired temperature for the contents of the drum. Start with a lower setting and gradually increase if higher temperatures are required.
- Abojuto Alapapo: The heater will begin to warm the drum. The thermostat will cycle the heating element on and off to maintain the set temperature.
- Idaabobo iwọn otutu ju: The maximum exposure temperature on the heating surface is 450°F (232°C). The thermostat will prevent the surface from exceeding this temperature.
- Agbara Pa: To turn off the heater, unplug it from the power outlet.
Akiyesi: The actual temperature of the drum contents may vary based on ambient temperature, drum material, and the specific properties of the material being heated. It is recommended to monitor the internal temperature of the drum contents, especially for temperature-sensitive materials.
6. Itọju
Regular maintenance ensures the longevity and safe operation of your BriskHeat DHCS13 drum heater.
- Ninu: Disconnect the heater from power before cleaning. Use a damp cloth to wipe down the exterior of the heater. Do not use abrasive cleaners or solvents that could damage the silicone rubber.
- Ayewo: Periodically inspect the heater for any signs of wear, damage, or fraying of the power cord. Check the integrity of the silicone rubber and the spring closure mechanism.
- Ibi ipamọ: When not in use, store the heater in a clean, dry place, away from direct sunlight and extreme temperatures.
- Awọn atunṣe: Do not attempt to repair damaged components yourself. Contact BriskHeat customer support or a qualified technician for repairs.
7. Laasigbotitusita
If you encounter issues with your DHCS13 drum heater, refer to the following common troubleshooting steps:
| Isoro | Owun to le Fa | Ojutu |
|---|---|---|
| Heater not warming up. | Ko si agbara si ẹrọ naa. Thermostat ṣeto ju kekere. Ipa agbara ti ko tọ. | Check if the heater is plugged in. Mu eto iwọn otutu pọ si. Ṣe idanwo iṣan jade pẹlu ẹrọ miiran tabi gbiyanju iṣan ti o yatọ. |
| Heater not reaching desired temperature. | Thermostat ṣeto ju kekere. Drum contents too cold or large volume. Poor contact with drum surface. | Mu eto iwọn otutu pọ si. Allow more time for heating, or consider additional insulation for the drum. Ensure the heater is snugly secured around the drum. |
| A máa ń lo ẹ̀rọ ìgbóná nígbà gbogbo. | Normal operation (thermostat maintaining temperature). Thermostat sensor issue. | This is typically normal. If cycling is excessive or erratic, contact support. |
| Visible damage to heater or cord. | Ipalara ti ara. | Immediately disconnect power. Do not use. Contact BriskHeat for repair or replacement. |
If the problem persists after attempting these solutions, please contact BriskHeat customer support.
8. Awọn pato
| Iwa | Iye |
|---|---|
| Nọmba awoṣe | DHCS13 |
| Ilu Agbara | 30-Gallon (114L) Metal Drums |
| Voltage | 120VAC |
| Wattis | 1000W |
| Thermostat otutu Ibiti | 50°F si 425°F (10°C si 218°C) |
| Maximum Exposure Temperature (Heating Surface) | 450°F (232°C) |
| Ohun elo | 2-Layer Fiberglass Reinforced Silicone Rubber |
| Dielectric Agbara | 2000V |
| Awọn iwọn (W x L) | 4ni (102mm) x 58.5in (1496mm) |
| Diameter (for drum) | 18.6ni (473mm) |
| Agbara Okun Ipari | 6ft (1.8m) |
| Pulọọgi Iru | Standard 3-prong (NEMA 5-15) |
| Ilẹ-ilẹ | Ni ilẹ |
9. Atilẹyin ọja ati Support
BriskHeat products are manufactured to the highest quality standards. For information regarding product warranty, please refer to the warranty statement provided with your purchase or visit the official BriskHeat webojula.
For technical assistance, troubleshooting beyond this manual, or to inquire about replacement parts, please contact BriskHeat customer support:
- Olupese: BriskHeat
- Ibi iwifunni: Refer to the BriskHeat webAaye tabi apoti ọja fun awọn alaye olubasọrọ tuntun julọ.
