1. Ọja Ipariview
The Lutron NTSTV-DV-WH is a Nova T fluorescent/LED single-pole slide dimmer designed for precise control of lighting levels. It features a classic thin profile with a linear slide mechanism for light level selection and an 'off' position. This dimmer is compatible with IEC60929 Annex E compliant LED drivers and electronic fluorescent ballasts.
Awọn ẹya pataki:
- Single-pole operation for 120/277V systems.
- Supports 0-10V dimming control.
- 8 Amp lọwọlọwọ Rating.
- Linear slide for intuitive light level adjustment.
- Adjustable high and low-end trim settings for fine-tuning.
- Requires Lutron PP-20 power pack for loads exceeding 8 amps (ta lọtọ).
Image Description: A white rectangular wall plate with a vertical slot in the center. Within the slot, a small white horizontal slide control is visible, positioned towards the bottom. The word "LUTRON" is subtly embossed on the slide control. The overall appearance is clean and minimalist.
2. Alaye Aabo
Please read and understand all instructions before installation. Improper installation can result in serious injury or death. This device must be installed by a qualified electrician in accordance with all national and local electrical codes.
- IKILO: Láti yẹra fún iná, ìpayà, tàbí ikú, pa agbára ní ibi tí ẹ̀rọ ìfọ́mọ́ tàbí àpótí fiusi wà kí o sì dán an wò pé agbára ti pa kí o tó fi wáyà sí i.
- Do not use this device with any load type other than specified (IEC60929 Annex E compliant LED drivers and electronic fluorescent ballasts).
- Rii daju pe gbogbo awọn asopọ waya wa ni aabo ati idabobo daradara.
- Do not install if the product appears damaged.
- Iwọn otutu ti nṣiṣẹ: 0 °C si 40 °C (32 °F si 104 °F).
3. Awọn ilana fifi sori ẹrọ
3.1. Ṣaaju ki o to Bẹrẹ
- Pa a agbara ni Circuit fifọ tabi fiusi nronu.
- Remove the existing wall plate and switch/dimmer.
- Verify the wiring configuration in your wall box. This dimmer is designed for single-pole applications.
- Ensure the load (LED drivers or fluorescent ballasts) is compatible with 0-10V dimming and the dimmer's specifications (120/277V, 8A max).
3.2. Awọn gbigbe
The NTSTV-DV-WH dimmer typically has two black wires for line/load connections and two low-voltage wires (often purple and gray/pink) for 0-10V control. The black line and load wires are interchangeable; either can be connected to the incoming power (line) and the other to the fixture (load). The 0-10V control wires are typically marked for polarity (e.g., '+' and '-').
- Connect one black dimmer wire to the incoming hot wire from the circuit breaker.
- Connect the other black dimmer wire to the load wire leading to the lighting fixture.
- Connect the ground wire from the wall box to the dimmer's ground screw (if present) or splice with the dimmer's ground wire.
- Connect the 0-10V control wires from the dimmer to the corresponding 0-10V control wires on the compatible LED driver or fluorescent ballast, observing polarity.
- Fun awọn ẹru ti o ju 8 lọ amps, a Lutron PP-20 power pack is required and must be wired according to its separate instructions.
3.3. Iṣagbesori
- Carefully fold wires into the wall box, ensuring no wires are pinched.
- Secure the dimmer to the wall box using the provided screws.
- So awo ogiri.
- Mu pada agbara ni awọn Circuit fifọ.
4. Operating Your Dimmer
4.1. Light Level Adjustment
To adjust the light level, simply slide the control lever up or down. Sliding the lever upwards increases the light intensity, while sliding it downwards decreases the intensity. Sliding the lever all the way down will turn the lights off.
4.2. Fine-Tuning (Trim Adjustment)
The NTSTV-DV-WH dimmer includes adjustable high-end and low-end trim screws located behind the cover plate. These allow for fine-tuning the maximum and minimum light output to optimize performance with your specific lighting fixtures.
- Remove the wall plate to access the trim screws.
- Use a small screwdriver to adjust the screws.
- Adjust the high-end trim to prevent flickering at maximum brightness.
- Adjust the low-end trim to ensure stable dimming at the lowest desired light level without the lights turning off prematurely.
- Replace the wall plate once adjustments are complete.
5. Itọju
The Lutron NTSTV-DV-WH dimmer requires minimal maintenance.
- Láti nu dimmer náà, fi asọ, d nu únamp asọ. Ma ṣe lo abrasive ose tabi epo.
- Ensure the dimmer and wall plate are free from dust and debris to maintain proper operation and appearance.
- Periodically check for any loose connections or signs of wear, especially during other electrical maintenance.
6. Laasigbotitusita
If you experience issues with your Lutron NTSTV-DV-WH dimmer, refer to the following common solutions:
| Isoro | Owun to le Fa | Ojutu |
|---|---|---|
| Lights do not turn on or off. | No power to the dimmer; incorrect wiring; tripped circuit breaker. | Check circuit breaker. Verify wiring connections. Ensure power is restored. |
| Lights do not dim or flicker at low levels. | Incompatible load; incorrect low-end trim setting; faulty fixture. | Ensure lighting fixtures are 0-10V dimmable. Adjust the low-end trim screw (refer to Section 4.2). Test with a known compatible fixture. |
| Lights flicker at high levels. | Incorrect high-end trim setting. | Adjust the high-end trim screw (refer to Section 4.2). |
| Dimmer nímọ̀lára gbígbóná. | Normal operation; overloaded circuit. | It is normal for dimmers to feel warm during operation. If it is excessively hot or emits smoke/odor, turn off power immediately and consult a qualified electrician. Ensure total load does not exceed 8 amps; use a power pack if necessary. |
If the problem persists after attempting these solutions, contact Lutron technical support.
7. Imọ ni pato
| Sipesifikesonu | Ẹ̀kúnrẹ́rẹ́ |
|---|---|
| Nọmba awoṣe | NTSTV-DV-WH |
| Ipo Isẹ | Dimmer ifaworanhan |
| Ti isiyi Rating | 8 Amps |
| Awọn ọna Voltage | 120V / 277V |
| Ọna Iṣakoso | 0-10V (IEC60929 Annex E compliant) |
| Awọn ẹrọ ibaramu | LED drivers and electronic fluorescent ballasts |
| Circuit Iru | 1-way (Single-pole) |
| Asopọmọra Iru | Dabaru ebute |
| Àwọ̀ | Funfun |
| Awọn iwọn (L x W x H) | Approximately 1 x 1 x 18 inches (Note: This dimension seems unusually long for a wall dimmer and may refer to packaging or a different measurement. Refer to product packaging for exact device dimensions.) |
| Iwọn Nkan | 7.2 iwon |
| International Idaabobo Rating | IP54 |
8. Atilẹyin ọja ati Support
For warranty information and technical assistance, please contact Lutron customer support directly. Lutron is known for providing excellent technical support to assist with product inquiries and troubleshooting.
You can typically find contact information on the official Lutron webaaye tabi laarin apoti ọja.
