Ìwé Ìtọ́sọ́nà Olùlò Fosmon HD8006 3-Gang 7.1 Àyíká Ohùn Pínpín Ilé Ilé Ìtàgé Àwo Ògiri

Ọrọ Iṣaaju

This manual provides comprehensive instructions for the installation, operation, and maintenance of your Fosmon HD8006 3-Gang 7.1 Surround Sound Distribution Home Theater Wall Plate. Please read this manual thoroughly before installation to ensure proper setup and optimal performance. Retain this manual for future reference.

Alaye Aabo

• Ensure power to the installation area is turned off before beginning any wiring to prevent electrical shock.
• Ọja yii jẹ apẹrẹ fun lilo inu ile nikan.
• Do not expose the wall plate to moisture or extreme temperatures.
• Use appropriate tools for installation. If unsure, consult a qualified electrician or installer.
• The subwoofer connection is an RCA connector on both the front and back side.
• The HDMI connection is an HDMI connector on both the front and back side.
• Banana jacks do not work with paired/dual banana plugs. Only single/individual banana plugs are compatible.

Package Awọn akoonu

• 1 x Fosmon HD8006 3-Gang 7.1 Surround Sound Distribution Home Theater Wall Plate
• Iṣagbesori skru

Note: Gang box/mounting bracket is not included and must be purchased separately.

Ọja Awọn ẹya ara ẹrọ

• 7.1 Surround Sound Support: Provides connections for 7 speakers (Front Left, Front Right, Center, Side Left, Side Right, Rear Left, Rear Right) and 1 subwoofer.
• Ibudo HDMI: Supports 4K@60Hz for high-resolution video signals.
• Awọn Asopọmọra Ti a Bo wura: Ensures improved signal quality and corrosion resistance for all banana binding posts, RCA jack, and HDMI port.
• 3-Gang Design: Fits standard 3-gang electrical boxes, offering a clean and organized installation.
• Idimu Cable Dinku: Allows for in-wall cable routing, providing a neat home theater setup.

Eto ati fifi sori

Follow these steps for proper installation of your Fosmon HD8006 wall plate. Ensure all power is disconnected before proceeding.

1. Múra Agbègbè Ìfìsílé náà sílẹ̀

• Turn off power to the circuit where you will be installing the wall plate.
• Install a standard 3-gang low-voltage mounting bracket or electrical box (not included) in your desired wall location. Ensure there is sufficient space behind the wall for cable routing.

Figure 1: The wall plate is compatible with a standard low-voltage 3-gang bracket (sold separately).

2. Route Cables

• Carefully route your speaker wires, subwoofer RCA cable, and HDMI cable through the wall to the opening of the mounting bracket. Leave enough slack for easy connection.

3. Connect Cables to the Wall Plate (Rear)

olusin 2: Ẹyìn view of the wall plate with binding posts, RCA, and HDMI connections.

• Awọn okun Agbọrọsọ: For each speaker, connect the positive (+) and negative (-) wires to the corresponding banana binding posts on the rear of the wall plate. Unscrew the binding post cap, insert the bare wire or spade connector, and tighten the cap. Ensure correct polarity (red for positive, black for negative) for each speaker channel (Front Left, Front Right, Center, Side Left, Side Right, Rear Left, Rear Right).
• Subwoofer RCA: Connect your subwoofer RCA cable to the RCA jack on the rear of the wall plate.
• Okun HDMI: Connect your HDMI cable to the HDMI port on the rear of the wall plate.

Figure 3: Speaker wires connected to the rear of the wall plate's binding posts.

4. So Àwo Ògiri náà

• Carefully push the connected wall plate into the mounting bracket/electrical box.
• Secure the wall plate to the mounting bracket using the provided screws. Do not overtighten.

Figure 4: The Fosmon HD8006 wall plate installed, showing front connections.

Awọn ilana Iṣiṣẹ

Once the Fosmon HD8006 wall plate is installed, you can connect your home theater components.

• Awọn isopọ Agbọrọsọ: Connect your speakers to the front banana binding posts using single banana plugs. Ensure each speaker is connected to its corresponding labeled post (e.g., Front Left speaker to "Front Left" post).
• Isopọ Subwoofer: Connect your subwoofer's RCA cable to the "Subwoofer" RCA jack on the front of the wall plate.
• HDMI Asopọ: Connect your HDMI source device (e.g., Blu-ray player, gaming console) or display device (e.g., TV, projector) to the "HDMI" port on the front of the wall plate.

Figure 5: Banana plugs connected to the front of the wall plate for speaker connections.

Note: Always ensure proper polarity for speaker connections to maintain optimal audio performance.

Itoju

• Keep the wall plate clean by wiping it with a soft, dry cloth.
• Avoid using harsh chemicals or abrasive cleaners, as these can damage the finish or connectors.
• Lojoojumọ, ṣayẹwo gbogbo awọn asopọ lati rii daju pe wọn wa ni aabo.

Laasigbotitusita

Awọn pato

Atilẹyin ọja ati Support

Fosmon products typically come with a limited lifetime warranty. For warranty claims, technical support, or customer service inquiries, please visit the official Fosmon website or contact their customer support team. Please have your product model number (HD8006) and purchase information ready.

Atilẹyin Ayelujara: www.fosmon.com/support