Leviton 003-84026-0 Stainless Steel 2-Gang Power Outlet Receptacle Wallplate Instruction Manual

Ọrọ Iṣaaju

This manual provides instructions for the proper installation and maintenance of the Leviton 003-84026-0 Stainless Steel 2-Gang Power Outlet Receptacle Wallplate. Please read these instructions carefully before beginning installation.

Alaye Aabo

• Máa pa agbára ní ibi tí ẹ̀rọ ìfọ́ tàbí àpótí fiusi bá wà kí o tó fi sori ẹrọ tàbí ṣe àtúnṣe.
• Ensure all wiring connections comply with local electrical codes.
• Ti o ko ba ni iyemeji nipa eyikeyi apakan ninu awọn itọnisọna wọnyi, kan si alamọdaju eleto ti o mọ.
• Ọja yii jẹ apẹrẹ fun lilo inu ile nikan.

Package Awọn akoonu

• Leviton 003-84026-0 Stainless Steel 2-Gang Wallplate
• Mounting Screws (typically included with wallplate)

Eto ati fifi sori

1. Pa Agbara: Locate the circuit breaker or fuse that controls the power to the outlet where the wallplate will be installed. Turn off the power completely. Verify power is off using a voltage idanwo.
2. Remove Old Wallplate: Carefully unscrew and remove the existing wallplate, if any.
3. Ipo ogiri tuntun: Align the Leviton 003-84026-0 wallplate over the electrical box, ensuring the openings match the receptacles.
4. Àwòrán Ìbòjútó Tí Ó Ní Ààbò: Insert the provided mounting screws into the designated holes on the wallplate and tighten them gently until the wallplate is flush with the wall. Do not overtighten, as this can damage the wallplate or the electrical box.
5. Pada Agbara pada: Once the wallplate is securely installed, restore power at the circuit breaker or fuse box.

Awọn ilana Iṣiṣẹ

The Leviton 003-84026-0 wallplate is a passive component designed to cover and protect electrical outlets. No specific operational steps are required beyond its proper installation. Ensure that the receptacles are fully accessible and that the wallplate does not obstruct their use.

Itoju

• Ninu: To clean the stainless steel wallplate, use a soft, damp cloth. For stubborn marks, a mild, non-abrasive cleaner suitable for stainless steel can be used. Avoid harsh chemicals or abrasive scrubbers, which can scratch the finish.
• Ayewo: Periodically inspect the wallplate for any signs of damage, such as cracks, discoloration, or loose screws. If damage is observed, turn off power and replace the wallplate.

Laasigbotitusita

• Àwòrán ògiri náà ti dẹ́: Ensure mounting screws are tightened appropriately. Do not overtighten.
• Wallplate Does Not Sit Flush: Check for obstructions behind the wallplate or ensure the electrical box is properly recessed.
• Scratches or Discoloration: Refer to the Maintenance section for cleaning instructions. Deep scratches may require replacement.

Awọn pato

This diagram illustrates the precise dimensions of the 2-gang wallplate. It shows a width of 2.750 inches (69.85 mm) for each opening, a total width of 4.56 inches (115.9 mm) for the 2-gang configuration, and a height of 4.500 inches (114.30 mm). The thickness is 0.220 inches (5.59 mm). Screw hole spacing and opening dimensions are also detailed.

Alaye atilẹyin ọja

Leviton products are backed by a limited warranty. For specific warranty terms and conditions, please refer to the official Leviton webojú òpó wẹ́ẹ̀bù tàbí kí o kàn sí olùrànlọ́wọ́ oníbàárà. Pa ẹ̀rí ríra rẹ mọ́ fún àwọn ẹ̀tọ́ ìdánilójú.

Atilẹyin ati Olubasọrọ

For technical assistance, product inquiries, or support, please visit the official Leviton webojula tabi kan si wọn onibara iṣẹ Eka. Alaye olubasọrọ le ṣee ri ni igbagbogbo lori olupese webaaye tabi apoti ọja.

• Olupese: Leviton
• Webojula: www.leviton.com