Sice Tech 70107 Remote Control Instruction Manual

1. Ifihan

This manual provides detailed instructions for the setup, operation, and maintenance of your Sice Tech 70107 4-button remote control. This device operates on a 433.92 MHz frequency and features fixed code technology with self-learning duplication capabilities. Please read this manual thoroughly before using the product to ensure proper function and longevity.

Image 1: The Sice Tech 70107 remote control. It features an orange casing with a white faceplate, four round orange buttons, and a small LED indicator. A black lanyard with a metal ring is attached to the bottom.

2. Package Awọn akoonu

• Sice Tech 70107 Remote Control (1 unit)
• Internal Battery (pre-installed or included separately)

3. Awọn pato

4. Setup and Programming (Self-Learning Duplication)

The Sice Tech 70107 remote control utilizes a self-learning duplication process to copy codes from an existing fixed-code remote.

4.1 Igbaradi akọkọ

1. Ensure your existing remote control is functional and has a working battery.
2. Place the Sice Tech 70107 remote control and your existing remote control side-by-side, as close as possible.

4.2 Clearing Existing Codes (Optional, but Recommended)

Before programming, it is recommended to clear any pre-existing codes from the Sice Tech 70107 remote.

• Press and hold two buttons simultaneously on the Sice Tech 70107 remote (e.g., the top two buttons) until the LED indicator flashes rapidly.
• Release the buttons. The remote is now cleared and ready for programming.

4.3 Programming a Button

1. Press and hold the button on the Sice Tech 70107 remote that you wish to program. The LED will light up steadily.
2. While holding the button on the Sice Tech 70107, press and hold the corresponding button on your existing remote control.
3. Keep both buttons pressed. The LED on the Sice Tech 70107 will flash slowly, then rapidly, indicating successful code duplication.
4. Tu awọn bọtini mejeeji silẹ.
5. Repeat this process for each button you wish to program.

Pataki: Ensure the existing remote is transmitting a strong signal during duplication. If programming fails, try again, ensuring the remotes are very close and the batteries are fresh.

5. Awọn ilana Iṣiṣẹ

Once programmed, the Sice Tech 70107 remote control operates identically to the original remote it duplicated.

• Lati muu ṣiṣẹ: Press the desired programmed button. The LED indicator will light up briefly, confirming transmission.
• Ibiti: The effective operating range may vary depending on environmental factors and the receiver unit.

6. Itọju

6.1 Ninu

Mu ese isakoṣo latọna jijin kuro pẹlu asọ ti o gbẹ. Ma ṣe lo abrasive ose tabi olomi, bi awọn wọnyi le ba casing and internal components.

6.2 Batiri Rirọpo

The remote control is powered by an internal battery. If the remote's range decreases significantly or the LED indicator does not light up, the battery may need replacement.

1. Ṣí iṣakoso latọna jijin pẹlu iṣọra casing. Refer to the product's physical design for the appropriate opening method (e.g., small screws, snap-fit tabs).
2. Ṣàkíyèsí irú àti ìtọ́sọ́nà bátìrì tó wà tẹ́lẹ̀.
3. Yọ batiri atijọ kuro ki o si fi tuntun ti iru kanna sii, ki o rii daju pe o peye polarity.
4. Pa casing ni aabo.

Iṣọra: Dispose of used batteries according to local regulations. Do not expose the remote to extreme temperatures or moisture.

7. Laasigbotitusita

• Remote not programming:
  • Ensure the existing remote is functional and has a fresh battery.
  • Make sure the Sice Tech 70107 remote is cleared of previous codes (Section 4.2).
  • Hold the remotes very close during the duplication process.
  • Ensure you are pressing and holding the buttons for the correct duration until the LED flashes rapidly.
  • Verify that the original remote is a fixed-code type operating at 433.92 MHz. This remote cannot duplicate rolling codes or other frequencies.
• Remote has short range or no response:
  • Check the battery in the Sice Tech 70107 remote and replace if necessary (Section 6.2).
  • Rii daju pe ko si awọn idena laarin isakoṣo latọna jijin ati olugba.
  • Environmental interference can affect range.
• Atọka LED ko tan ina:
  • The battery may be depleted. Replace the battery (Section 6.2).

8. Atilẹyin ọja ati Support

For warranty information or technical support, please refer to the documentation provided with your purchase or contact Sice Tech directly through their official webAaye ayelujara tabi awọn ikanni iṣẹ alabara. Pa ẹri rira rẹ mọ fun awọn ẹtọ atilẹyin ọja.