Behringer iNUKE NU3000 Power Amplifier Afowoyi olumulo

1. Ifihan

Thank you for choosing the Behringer iNUKE NU3000 Power Amplifier. Eyi amplifier is designed for professional audio applications, offering high power output in a lightweight, high-density Class-D design. It features advanced technologies for reliable performance and efficient power consumption.

Awọn ẹya pataki pẹlu:

• Delivers 2 x 1500 Watts into 2 Ohms; 2 x 900 Watts into 4 Ohms; 3000 Watts into 4 Ohms (bridge mode).
• Ultra-lightweight design, weighing less than 7 lbs (3.3 kg).
• Revolutionary cool-running High-Density Class-D technology for reliability.
• Ultra-efficient switch-mode power supply for noise-free audio and superior transient response.
• "Zero-Attack" limiters for maximum output level with reliable overload protection.
• Built-in stereo crossover with low-cut, high-cut, and full range modes.

2. Awọn Ilana Aabo pataki

• Read these instructions thoroughly before operation.
• Pa awọn ilana wọnyi fun itọkasi ọjọ iwaju.
• Heed all warnings on the product and in this manual.
• Maṣe lo ohun elo yii nitosi omi.
• Mọ pẹlu asọ gbigbẹ nikan.
• Ma ṣe dina eyikeyi awọn ṣiṣi atẹgun. Fi sori ẹrọ ni ibamu pẹlu awọn ilana ti olupese.
• Maṣe fi sori ẹrọ nitosi awọn orisun ooru gẹgẹbi awọn imooru, awọn iforukọsilẹ ooru, awọn adiro, tabi awọn ohun elo miiran (pẹlu ampliifiers) ti o gbe ooru jade.
• Ma ṣe ṣẹgun idi aabo ti polarized tabi pilogi iru ilẹ. Plọọgi polarized ni awọn abẹfẹlẹ meji pẹlu ọkan gbooro ju ekeji lọ. Plọọgi iru-ilẹ ni awọn abẹfẹlẹ meji ati prong grounding kẹta. Abẹfẹlẹ ti o gbooro tabi prong kẹta ni a pese fun aabo rẹ. Ti pulọọgi ti a pese ko ba wo inu iṣan-ọna rẹ, kan si alamọdaju kan fun rirọpo ti iṣan igba atijọ.
• Dabobo okun agbara lati ma rin lori tabi pin, ni pataki ni awọn pilogi, awọn ohun elo irọrun, ati aaye nibiti wọn ti jade kuro ninu ohun elo naa.
• Lo awọn asomọ/awọn ẹya ara ẹrọ ti olupese pato.
• Yọọ ohun elo yi nigba iji manamana tabi nigba lilo fun igba pipẹ.
• Tọkasi gbogbo iṣẹ si awọn oṣiṣẹ iṣẹ ti o peye. Iṣẹ nilo nigbati ohun elo ba ti bajẹ ni ọna eyikeyi, gẹgẹbi okun ipese agbara tabi plug ti bajẹ, omi ti ta silẹ tabi awọn nkan ti ṣubu sinu ẹrọ, ohun elo naa ti farahan si ojo tabi ọrinrin, ko ṣiṣẹ deede. , tabi ti lọ silẹ.

3. Unpacking ati Ibẹrẹ Ayewo

Upon receiving your iNUKE NU3000 amplifier, carefully unpack it and inspect for any signs of damage that may have occurred during transit. If damage is found, notify your dealer immediately. Retain the original packing materials for future shipping or storage.

4. Eto

4.1 agbeko iṣagbesori

The iNUKE NU3000 is designed for standard 19-inch rack mounting. Ensure adequate ventilation around the unit, especially at the front and rear vents, to prevent overheating.

4.2 Awọn isopọ

Ṣaaju ṣiṣe eyikeyi awọn isopọ, rii daju awọn amplifier is powered off and disconnected from the mains supply.

Figure 1: Front panel of the Behringer iNUKE NU3000, showing input gain controls and power switch.

Figure 2: Rear panel of the Behringer iNUKE NU3000, displaying input connectors, output connectors, and crossover/mode switches.

Inputs (Figure 2, right side):

• Connect your audio source (e.g., mixer, audio interface) to the XLR/TRS combo input jacks for Channel A and Channel B.

Outputs (Figure 2, left side):

• Connect your loudspeakers to the professional locking speaker connectors (Speakon-compatible) for Channel A and Channel B.
• Ensure correct wiring and impedance matching for your speakers. The amplifier supports 2 Ohm and 4 Ohm loads per channel, and 4 Ohm in bridge mode.

Asopọ agbara:

• Connect the supplied AC power cord to the IEC inlet on the rear panel (Figure 2, far left).
• Plug the other end into a suitable mains power outlet.

5. Ṣiṣẹ awọn Ampitanna

5.1 Agbara Tan / Pa

• Press the POWER button on the front panel (Figure 1, far right) to turn the amplifier tan tabi pa.
• Allow a few seconds for the amplifier to stabilize after powering on.

5.2 Gain Controls

• The large rotary knobs on the front panel (Figure 1, center) control the input gain for Channel A and Channel B independently.
• Adjust these to achieve the desired output level without clipping.

5.3 Awọn itọkasi

• AGBARA LED: Ṣe itanna nigbati ẹrọ naa ba wa ni titan.
• Awọn LED SIGN: Indicate the presence of an audio signal.
• LIMIT LEDs: Illuminate when the "Zero-Attack" limiter is active, indicating the amplifier is approaching its maximum output. Occasional flickering is normal; continuous illumination suggests the input level is too high or the amplifier ti wa ni overdriven.
• PROTECT LEDs: Illuminate if the amplifier enters protection mode due to overheating, short circuits, or other faults.

5.4 Rear Panel Controls (Figure 2)

• Iyipada Iyipada: Selects between Stereo, Parallel, or Bridge operating modes.
• CROSSOVER Switch: Engages the built-in stereo crossover. Options include Full Range, Low Cut, and High Cut.
• LOW CUT/HIGH CUT Frequency: Adjusts the crossover frequency when Low Cut or High Cut modes are selected.

6. Itọju

6.1 Ninu

Mọ awọn amplifier's exterior with a soft, dry cloth. Do not use liquid cleaners or solvents. Ensure ventilation grilles are free from dust and debris to maintain proper airflow.

6.2 Fentilesonu

Regularly check that the front and rear ventilation openings are not obstructed. Proper airflow is crucial for the amplifier's long-term reliability and performance, especially given its high-density Class-D design.

7. Laasigbotitusita

• Ko si Agbara: Check the power cord connection, the mains outlet, and the power switch.
• Ko si Ohun: Verify all audio input and output connections. Check the source device and speaker connections. Ensure gain controls are not set to minimum. Check MODE and CROSSOVER settings.
• Distortion/Clipping: Reduce input gain from the source or on the amplifier. Ensure speaker impedance matches the amplifier's capabilities. Continuous LIMIT LED illumination indicates excessive signal levels.
• PROTECT LED On: Disconnect speakers and power off the unit. Allow it to cool down. Check speaker cables for short circuits. If the issue persists, seek professional service.
• Ariwo afẹ́fẹ́ tó pọ̀ jù: Ensure ventilation openings are clear. If noise is unusually loud or persistent, it may indicate a fan issue requiring service.

8. Awọn pato

9. Atilẹyin ọja ati Support

For detailed warranty information and to register your product, please visit the official Behringer website. Technical support and service inquiries should be directed to authorized Behringer service centers or your local dealer.

No official product videos were provided in the source data for embedding in this manual.