Mopar OEM Dodge Ram 6.7L Diesel Fuel Filter Water Separator Set Instruction Manual

1. Ọja Ipariview

This document provides instructions for the installation and maintenance of the Mopar OEM Fuel Filter and Water Separator Set for Dodge Ram 6.7 Liter Cummins Turbo Diesel engines. This set includes two essential fuel filters designed to ensure clean fuel delivery and protect your engine from contaminants and water.

2. Ibamu

This fuel filter and water separator set is compatible with the following vehicles:

• 2013-2019 Ram 2500 6.7L
• 2013-2019 Ram 3500 6.7L
• 2013-2017 Ram 4500 6.7L
• 2013-2017 Ram 5500 6.7L

The 6.7L diesel engines require two fuel filters: one located in the front engine compartment and another near the fuel tank in the rear.

Image 1: Part Fitment Table showing compatible Ram models and years for the 6.7L Diesel engine.

3. Alaye Aabo

Always prioritize safety when performing vehicle maintenance. Fuel is highly flammable. Ensure adequate ventilation and avoid open flames or sparks. Wear appropriate personal protective equipment, including safety glasses and gloves. Refer to your vehicle's official service manual for specific safety precautions and detailed procedures.

4. Package Awọn akoonu

Your Mopar OEM Fuel Filter Water Separator Set includes:

• 1x Front Fuel Filter (Engine Compartment)
• 1x Rear Fuel Filter (Near Fuel Tank)
• Associated O-rings for both filters

Image 2: Mopar OEM Fuel Filter with included O-rings, as typically supplied in the product packaging.

5. Awọn ilana fifi sori ẹrọ

It is highly recommended to consult your vehicle's specific service manual for detailed, step-by-step instructions and torque specifications. The following is a general guide.

5.1. Rear Fuel Filter (Under Bed)

1. Prepare for Drainage: Place a suitable drain pan or bucket beneath the rear fuel filter housing to collect any spilled fuel.
2. Idana fifa: Open the drain valve on the bottom of the fuel filter housing to allow fuel to drain. Use a hose if necessary to direct the fuel into the pan.
3. Yọ Ajọ atijọ kuro: Once drained, use a 29mm socket or appropriate filter wrench to loosen and remove the fuel filter housing. Carefully pull out the old filter element.
4. Replace O-ring: Remove the old O-ring from the housing and install the new O-ring provided with the Mopar filter. Lubricate the new O-ring with clean diesel fuel or a suitable lubricant.
5. Fi Ajọ Tuntun sori ẹrọ: Insert the new Mopar fuel filter into the housing. Ensure it is seated correctly.
6. Tún so Ilé Mọ́: Thread the housing back into place and tighten it using the 29mm socket. Do not overtighten. Close the drain valve.

5.2. Front Fuel Filter (Engine Bay)

1. Prepare for Drainage: Place a drain pan or bucket beneath the front fuel filter housing.
2. Idana fifa: Locate the drain valve on the front fuel filter housing. Open it to drain fuel into the pan.
3. Yọ Ajọ atijọ kuro: Use a 29mm socket or appropriate tool to remove the fuel filter cap. Carefully pull out the old filter element.
4. Replace O-ring: Remove the old O-ring from the cap and install the new O-ring provided with the Mopar filter. Lubricate the new O-ring with clean diesel fuel or a suitable lubricant.
5. Fi Ajọ Tuntun sori ẹrọ: Insert the new Mopar fuel filter into the housing. Ensure it is seated correctly.
6. Tun Fila: Thread the cap back into place and tighten it using the 29mm socket. Do not overtighten. Close the drain valve.

5.3. Post-Installation Steps

1. Eto Epo akọkọ: Cycle the ignition key to the 'ON' position (without starting the engine) several times for 15-30 seconds each time. This allows the fuel pump to prime the system and remove air from the lines.
2. Start Engine and Check for Leaks: Start the engine and let it idle. Carefully inspect both fuel filter housings for any signs of fuel leaks. If leaks are present, shut off the engine immediately and re-check the installation.
3. Reset Fuel Filter Life Monitor (if applicable): If your vehicle has a fuel filter life monitoring system, follow your vehicle's instructions to reset it.

6. Itọju

Regular replacement of your fuel filters is crucial for maintaining optimal engine performance and longevity. Refer to your Dodge Ram's owner's manual or service schedule for recommended replacement intervals. Typically, diesel fuel filters should be replaced every 15,000 to 20,000 miles, or as specified by the manufacturer, depending on driving conditions and fuel quality.

7. Laasigbotitusita

If you experience issues after replacing your fuel filters, consider the following:

• Engine Crans ṣugbọn kii yoo Bẹrẹ: This could indicate air in the fuel system. Ensure the system was properly primed after installation. Repeat the priming procedure.
• Reduced Engine Performance/Rough Idling: Check for any fuel leaks around the filter housings. Ensure all connections are secure and O-rings are properly seated.
• Jijo epo: Immediately shut off the engine. Verify that the filter housings are tightened correctly and that the O-rings are not pinched or damaged.

If problems persist, consult a certified mechanic or your vehicle's service center.

8. Awọn pato

9. Atilẹyin ọja ati Support

For warranty information or technical support regarding your Mopar OEM Fuel Filter Water Separator Set, please refer to the documentation included with your purchase or contact Mopar customer service directly. You may also reach out to your authorized Mopar dealer or the seller for assistance.