1. Ifihan
This manual provides instructions for the proper use and maintenance of the Oakton AO-35613-22 pH 6+ Handheld Meter. This portable device is designed for accurate pH measurements in various applications. Please read this manual thoroughly before operating the meter.
2. Alaye Aabo
- Always handle the pH probe with care.
- Do not immerse the meter body in liquid.
- Use only specified batteries (4 AAA).
- Jeki ẹrọ naa kuro ni arọwọto awọn ọmọde.
- Refer to local regulations for proper disposal of batteries and electronic waste.
3. Package Awọn akoonu
Rii daju pe gbogbo awọn nkan wa lori ṣiṣi silẹ:
- Oakton AO-35613-22 pH 6+ Handheld Meter
- Iwadi pH
- ATC (Automatic Temperature Compensation) Probe
- Boot roba Idaabobo
- 4 Awọn batiri AAA
4. Ọja Ipariview
The Oakton AO-35613-22 is a portable pH meter designed for accurate and rapid measurements. It features an LCD display, intuitive controls, and automatic temperature compensation.
Nọmba 1: Oakton AO-35613-22 pH 6+ Handheld Meter. The image shows the meter with its LCD display showing '7.00 pH', and connected pH and temperature probes. The meter is encased in a protective rubber boot.
Awọn ẹya pataki:
- Portable design for field and lab use.
- Ifihan LCD fun awọn kika kika kedere.
- pH range: 0.00 to 14.00.
- mV range: ±1999.
- Temperature range: -10 to 110 °C.
- Automatic Temperature Compensation (ATC) from 0 to 100 °C.
- Protective rubber boot for durability and as a meter stand.
5. Eto
5.1 Fifi sori batiri
- Yọ bata roba aabo kuro.
- Wa ideri ibi ipamọ batiri naa ni ẹhin mita naa.
- Open the cover and insert four (4) AAA batteries, observing polarity.
- Replace the battery compartment cover and the protective rubber boot.
5.2 Iwadi Asopọ
- Connect the pH probe to the BNC connector on the top of the meter.
- Connect the ATC probe to the mini-jack connector next to the BNC connector.
- Rii daju pe awọn asopọ wa ni aabo.
6. Awọn ilana Iṣiṣẹ
6.1 Agbara Tan / Pa
- Tẹ awọn TAN/PA bọtini lati tan mita naa.
- Tẹ awọn TAN/PA button again to turn the meter off.
6.2 Gbigba Idiwon
- Ensure the meter is calibrated (refer to Section 7).
- Rinse the pH probe and ATC probe with distilled water.
- Immerse both probes into the sample solution. Ensure the probe tips are fully submerged.
- Allow the reading to stabilize on the LCD display.
- Tẹ awọn HOLD/ENTER button to freeze the reading if desired. Press again to release.
- After measurement, rinse probes thoroughly with distilled water and store them properly.
6.3 Aṣayan ipo
Tẹ awọn MODE/°C/°F button to switch between pH, mV, and temperature display modes.
7. Iṣatunṣe
Regular calibration is essential for accurate pH measurements. The meter supports up to 5-point calibration with NIST and USA buffer recognition.
- Prepare fresh pH buffer solutions (e.g., pH 4.01, 7.00, 10.01).
- Rinse the pH and ATC probes with distilled water.
- Immerse both probes into the first buffer solution (e.g., pH 7.00).
- Tẹ awọn CAL button. The meter will automatically recognize the buffer and calibrate.
- Once stable, rinse probes and repeat the process for subsequent buffer solutions (e.g., pH 4.01, then pH 10.01).
- Refer to the full calibration procedure in the detailed manual for advanced settings and multi-point calibration.
8. Itọju ati Itọju
8.1 Ninu
- Wipe the meter body clean with a damp asọ. Ma ṣe lo abrasive ose tabi epo.
- Rinse the pH probe thoroughly with distilled water after each use.
- For stubborn deposits on the pH probe, consult the probe's specific cleaning instructions.
8.2 Ibi ipamọ
- Always store the pH probe in its storage solution or a suitable buffer solution to prevent drying out. Never store dry.
- Tọ́jú mita náà sí ibi tí ó tutù tí ó sì gbẹ nígbà tí a kò bá lò ó.
- Yọ awọn batiri kuro ti o ba fipamọ fun awọn akoko ti o gbooro lati ṣe idiwọ jijo.
9. Laasigbotitusita
| Isoro | Owun to le Fa | Ojutu |
|---|---|---|
| Ko si ifihan | Awọn batiri ti o ku tabi ti ko tọ ti fi sori ẹrọ. | Ṣayẹwo polarity batiri; ropo awọn batiri. |
| Awọn kika aiduro | Probe not immersed correctly; dirty probe; old buffer solutions; damaged probe. | Ensure proper immersion; clean probe; use fresh buffer solutions; replace probe if damaged. |
| Aṣiṣe odiwọn | Incorrect buffer solution; dirty probe; expired buffer. | Verify buffer values; clean probe; use fresh buffer solutions. |
10. Awọn pato
| Ọja Iru | pH Mita |
| Meter Style | Gbigbe |
| Ifihan Iru | LCD |
| pH Ibiti | 0.00 si 14.00 pH |
| Ipinnu pH | 0.01 tabi 0.1 pH |
| pH Yiye | ± 0.01 pH |
| mV Ibiti | ± 1999 mV |
| mV Resolution | 1 mV |
| mV Accuracy | ±0.2 mV or 0.05% (whichever is greater) |
| Iwọn otutu | -10 si 110 °C |
| Biinu iwọn otutu | Automatic (0 to 100 °C) |
| Buffer Recognition | NIST and USA |
| Idiwọn Points | Titi di awọn aaye 5 |
| Orisun agbara | 4 AAA batiri |
| Igbesi aye batiri | O fẹrẹ to awọn wakati 700 |
| Awọn iwọn (W x H) | 8.57 cm x 4.29 cm (3 3/8 in x 1 11/16 in) |
| Ohun elo ita | Rubber (protective boot) |
11. atilẹyin ọja Information
The Oakton AO-35613-22 pH 6+ Handheld Meter comes with a 3-odun atilẹyin ọja from the date of purchase. This warranty covers defects in materials and workmanship under normal use. Please retain your proof of purchase for warranty claims. The warranty does not cover damage caused by misuse, accident, unauthorized modification, or improper storage of the pH probe.
12. Atilẹyin ati Olubasọrọ
For technical assistance, troubleshooting beyond this manual, or warranty service, please contact Oakton customer support or visit the official Oakton website. Contact information can typically be found on the product packaging or the manufacturer's webojula.
Manufacturer: Cole-Parmer
Webojula: Visit the Oakton Store on Amazon
