Ọrọ Iṣaaju
The HOBO UX100-003 is a compact USB data logger designed to accurately record temperature and relative humidity in indoor environments. It is suitable for monitoring conditions in various settings such as office buildings, warehouses, server rooms, and museums. This device stores over 42,000 temperature and humidity readings and features a user-replaceable battery. Data configuration and retrieval are managed through the free HOBOware software, compatible with both PC and Mac operating systems.
Ṣeto
1. Software fifi sori
Before using the data logger, install the HOBOware software on your computer. This software is required for configuring the logger, launching logging sessions, and offloading recorded data. HOBOware is available as a free download for both Windows and macOS operating systems from the official HOBO webojula.
2. Fifi sori batiri
The UX100-003 uses a user-replaceable CR2032 coin cell battery. Ensure the battery is correctly installed before initial use. The typical battery life is one year. Refer to the Maintenance section for detailed battery replacement instructions.
3. Iṣeto ni ibẹrẹ
- Connect the HOBO UX100-003 data logger to your computer's USB port.
- Launch the HOBOware software.
- Use the software to configure logging parameters such as logging interval, start time, and alarm thresholds.
- Once configured, disconnect the logger from the USB port.
Awọn ilana Iṣiṣẹ
1. imuṣiṣẹ
Place the data logger in the desired indoor environment where temperature and humidity monitoring is required. Ensure the sensor area (vented section on the right side of the device) is not obstructed to allow for accurate readings.
2. Gedu data
Once configured and launched via HOBOware, the logger will automatically begin recording temperature and relative humidity data at the specified intervals. The LCD display will show current readings, logging status, and battery level.
3. Data igbapada
- To retrieve data, connect the logger to your computer's USB port.
- Open the HOBOware software.
- Use the software to offload the recorded data. The data can then be viewed, atupale, ati okeere fun lilo siwaju sii.
- After offloading, you can choose to stop the current logging session or reconfigure and launch a new one.
Itoju
Batiri Rirọpo
The HOBO UX100-003 is powered by one CR2032 lithium coin cell battery. When the battery indicator on the LCD display shows low power, or if the logger stops functioning, replace the battery promptly.
- Ensure the logger is not actively logging data. If it is, stop the logging session using HOBOware.
- Wa yara batiri lori ẹrọ naa.
- Ṣí yàrá náà dáadáa kí o sì yọ bátìrì CR2032 àtijọ́ náà kúrò.
- Insert a new CR2032 battery, observing the correct polarity (+/-).
- Pa yara batiri naa ni aabo.
- After battery replacement, it is recommended to connect the logger to HOBOware to verify functionality and re-launch a logging session if needed.
Ninu
Clean the exterior of the data logger with a soft, damp cloth. Do not use abrasive cleaners or solvents. Ensure the sensor area remains free of dust and debris for accurate readings.
Laasigbotitusita
- Logger Not Connecting to HOBOware:
Ensure the USB cable is securely connected to both the logger and the computer. Try a different USB port or cable. Verify that HOBOware software is installed correctly and is the latest version. Restart your computer if necessary.
- Logger Display is Blank or Unresponsive:
Check the battery level. If the battery is low or depleted, replace it as described in the Maintenance section. If the issue persists after battery replacement, try removing and re-inserting the battery to reset the device.
- Awọn kika ti ko pe:
Ensure the logger's sensor area is not obstructed by dust, debris, or placed in an area with poor air circulation. Avoid placing the logger near heat sources, direct sunlight, or areas with rapid temperature/humidity fluctuations that do not represent the general environment.
- Logging Session Not Starting:
Connect the logger to HOBOware and verify that a logging session has been properly configured and launched. Check for any error messages within the software.
Awọn pato
| Ẹya ara ẹrọ | Ẹ̀kúnrẹ́rẹ́ |
|---|---|
| Awoṣe | UX100-003 |
| Iwọn otutu | -20°C si +70°C (-4°F si +158°F) |
| Ojulumo ọriniinitutu Range | 15% to 95% RH ti kii-condensing |
| Yiye iwọn otutu | ±0.21°C lati 0° si 50°C (± 0.38°F lati 32° si 122°F) |
| RH Yiye | ±3.5% RH from 25% to 85% RH (typical) |
| Agbara Ibi ipamọ data | Over 42,000 temperature and humidity readings |
| Wọle Aarin | 1 second to 18 hours (configurable via HOBOware) |
| Batiri Iru | CR2032 3V Lithium Coin Cell (user-replaceable) |
| Igbesi aye batiri | Ọdun 1 (aṣoju) |
| Ni wiwo | USB |
| Awọn iwọn (H x W x D) | 3.44 x 1.44 x 0.6 inches (8.74 x 3.66 x 1.52 cm) |
| Iwọn | 0.32 iwon (9 giramu) |
| Mabomire Rating | IP50 |
| Ti beere fun Software | HOBOware or HOBOware Pro (free download) |
Alaye atilẹyin ọja
The HOBO UX100-003 Data Logger comes with a 1-odun olupese ká atilẹyin ọja. This warranty covers defects in materials and workmanship under normal use. For specific terms and conditions, please refer to the warranty documentation provided with your purchase or contact HOBO customer support.
Atilẹyin
For further assistance, technical support, or to download the latest version of HOBOware software, please visit the official HOBO webaaye. Awọn website provides comprehensive resources, including FAQs, user forums, and contact information for customer service.
HOBOware Software: The free HOBOware software is essential for full functionality of your data logger. It allows for device configuration, data download, and analysis. Ensure you are using the latest version for optimal performance.
