Futaba 18SZA 18-Channel Radio Control Transmitter User Manual

1. Ifihan

O ṣeun fun riraasing the Futaba 18SZA 18-Channel Computerized Radio Control Transmitter. This advanced system is designed for precise control and extensive telemetry capabilities across various model types, including airplanes, helicopters, gliders, and multi-rotor drones. This manual provides detailed instructions for setup, operation, maintenance, and troubleshooting to ensure safe and optimal performance of your transmitter.

2. Alaye Aabo

Always operate your radio control system responsibly. Failure to follow these safety guidelines may result in injury or damage to property.

• Aabo Batiri: Use only the specified battery and charger. Do not short-circuit, disassemble, or expose batteries to extreme temperatures.
• Ayika Ṣiṣẹ: Do not operate the transmitter in rain, high humidity, or near strong electromagnetic interference.
• Ṣiṣayẹwo Ọkọ ofurufu: Ṣe àyẹ̀wò ibi tí a ti ń ṣàkóso nígbà gbogbo kí o sì rí i dájú pé gbogbo ibi tí a ti ń ṣàkóso dáhùn dáadáa kí o tó fò ní gbogbo ìgbà.
• Laini Oju: Maintain visual line of sight with your model at all times during operation.
• Awọn ọmọde: Keep the transmitter and accessories out of reach of small children.

3. Package Awọn akoonu

Daju pe gbogbo awọn nkan ti a ṣe akojọ rẹ si isalẹ wa ninu package rẹ:

• Futaba 18SZA Transmitter
• R7008SB olugba
• 6.6V 2100mAh LiFe Battery (installed in transmitter)
• Ṣaja batiri
• Yipada ijanu
• Okun Ọrun
• Ilana Afowoyi (iwe yii)

Image: The Futaba 18SZA transmitter shown with its accompanying accessories, including the R7008SB receiver, battery, charger, and switch harness.

4. Ọja Ipariview

Familiarize yourself with the various components and controls of your Futaba 18SZA transmitter.

Aworan: Iwaju view of the Futaba 18SZA transmitter, highlighting the dual stick assemblies, various switches, dials, and the central touchscreen display.

Aworan: Angled view of the Futaba 18SZA transmitter, showing the antenna, top switches, and the ergonomic design.

4.1. Awọn iṣakoso ati Awọn ẹya ara ẹrọ

• Stick Assemblies: Precision quad bearing stick assemblies for smooth and accurate control.
• Yipada Yipada: Eight programmable toggle switches (six 3-position, one 2-position, one momentary) for various functions.
• Side Levers & Dials: Two side levers and two dials for additional proportional control.
• Digital Trims: Six digital trims for fine-tuning control surfaces.
• Ifihan iboju ifọwọkan: 4.3-inch wide full-color LED touchscreen for intuitive menu navigation and programming.
• Eriali: Integrated 2.4GHz antenna for reliable signal transmission.
• S.Bus2 Port: For connecting S.Bus2 telemetry sensors and programming S.Bus servos.

Aworan: Isunmọ view of one of the stick assemblies on the Futaba 18SZA, showing its detailed construction and adjustability.

Image: Close-up of the bottom rear section of the Futaba 18SZA, showing the S.I./F port and the serial number label.

5. Eto

5.1. Ngba agbara si Batiri naa

1. So ṣaja pọ si ọna agbara ti o yẹ.
2. Plug the charger's output connector into the charging port on the transmitter. The charging port is typically located on the back or side of the transmitter.
3. Allow the battery to charge fully. Refer to the charger's indicator lights for charging status. A full charge typically takes several hours.
4. Ge asopọ ṣaja ni kete ti gbigba agbara ti pari.

Akiyesi: The 18SZA uses a 6.6V 2100mAh LiFe battery. Only use the supplied charger or a compatible LiFe charger.

5.2. Binding the Receiver (R7008SB)

Binding establishes a secure communication link between your transmitter and receiver.

1. Ensure the transmitter is turned OFF.
2. Connect a battery to the R7008SB receiver. The receiver's LED will begin to flash red.
3. Press and hold the Link button on the R7008SB receiver. The LED will change from flashing red to solid red.
4. While holding the Link button, turn ON the transmitter.
5. Release the Link button on the receiver after a few seconds. The receiver's LED should now be solid green, indicating a successful bind.
6. Turn OFF both the transmitter and receiver, then turn them ON again to confirm the bind.

5.3. Initial Power-On and Model Selection

1. Ensure all switches are in their neutral or off positions.
2. Press and hold the power button on the transmitter until the screen illuminates.
3. Upon first power-on, you may be prompted to set basic system parameters. Follow the on-screen instructions.
4. From the main menu, select 'Model Select' to choose an existing model or create a new one. The 18SZA supports 15-character user and model naming.
5. Select the appropriate model type (Airplane, Helicopter, Glider, or Multi-rotor) for your new model.

6. Ṣiṣẹ

6.1. Menu Navigation and Touchscreen Use

The 18SZA features a responsive touchscreen for easy navigation. Tap icons or menu items to select them. Swipe to scroll through lists or pages.

6.2. Basic Programming Features

Access the 'System Menu' or 'Linkage Menu' to configure various settings:

• Sub Trims: Fine-tune the neutral position of servos.
• Servo Reversing: Change the direction of servo movement.
• End Point Adjustment (EPA): Set the maximum travel limits for each servo.
• AFR D/R (Dual Rate/Exponential): Adjust control sensitivity around center stick and at full deflection. The 18SZA offers 3 AFR curve modes with 17 points for precise customization.
• Programmable Mixing: Create custom mixes between channels for advanced control setups (e.g., flaperons, V-tail).
• Throttle Cut & Idle Down: Essential safety features for engine models.
• Logic Switches: Define conditions for activating specific functions.

6.3. Telemetry Functions

The 18SZA supports S.Bus2 telemetry sensors, providing real-time data during flight. Compatible sensors can monitor:

• Batiri Voltage (Rx and External)
• Iwọn otutu
• RPM
• Giga
• GPS data
• Current/Capacity

Telemetry alarms can be set for various parameters, providing audible alerts via the internal speaker or headphones, or tactile vibrations.

6.4. Timers and Alarms

The transmitter includes multiple timers and alarm functions:

• Up/Down Timers: Two configurable timers for flight duration or specific tasks.
• System Timer: Tracks total operating time of the transmitter.
• Model Timer: Tracks total operating time for the selected model.
• Throttle Stick Alarm: Alerts if the throttle stick is not at idle when powering on.
• Itaniji Voltage: Configurable low voltage alarm for the transmitter battery.
• Alarm Vibrator: Provides haptic feedback for alarms.

7. Itọju

7.1. Ninu

Wipe the transmitter's exterior with a soft, dry cloth. For stubborn dirt, use a slightly damp cloth with mild soap, then wipe dry. Do not use solvents or abrasive cleaners.

7.2. Ibi ipamọ

Store the transmitter in a cool, dry place away from direct sunlight and extreme temperatures. If storing for extended periods, ensure the battery is charged to approximately 50% capacity.

7.3. Itọju batiri

Lati pẹ igbesi aye batiri:

• Yago fun gbigba agbara si batiri ni kikun.
• Do not leave the battery connected to the charger indefinitely after it's fully charged.
• If the transmitter will not be used for a long time, charge the battery to storage voltage (around 3.8V per cell for LiFe, or 50% capacity).

8. Laasigbotitusita

9. Awọn pato

10. Atilẹyin ọja ati Support

Futaba products are manufactured to high standards and are backed by a limited warranty against defects in materials and workmanship. For specific warranty terms and conditions, please refer to the warranty card included with your product or visit the official Futaba webojula.

For technical support, service, or replacement parts, please contact your local Futaba distributor or authorized service center. Contact information can typically be found on the Futaba webaaye tabi ninu apoti ọja rẹ.

When contacting support, please have your product model number (FUTK9510) and serial number ready.