BISSELL CrossWave 17132 3-in-1 Multi-Surface Floor Cleaner User Manual

Ọja Pariview

The BISSELL CrossWave 17132 is a versatile 3-in-1 multi-surface floor cleaner designed to vacuum, wash, and dry hard floors, carpets, and rugs simultaneously. This integrated cleaning system offers an efficient alternative to traditional vacuuming and mopping, providing thorough cleaning with less effort. Its dual tank technology ensures that clean water and formula are always separate from dirty water, guaranteeing a fresh clean every time.

Awọn irinše to wa

Before beginning assembly, ensure all components are present in the packaging:

• BISSELL CrossWave 17132 Unit (Main Body and Handle)
• Multi-Surface Cleaning Formula (Detergent)
• Multi-Surface Brush Roll (Replacement Brush)
• Storage and Cleaning Tray (Station)

Image: The BISSELL CrossWave 17132 unit shown with its accompanying multi-surface cleaning formula, an extra brush roll, and the storage and cleaning tray.

Awọn ilana iṣeto

Apejọ

1. Fi ọwọ́ náà sínú ara àkọ́kọ́ ti ẹ̀rọ náà títí tí yóò fi tẹ ibi tí ó wà dáadáa.
2. Ensure the clean water tank is properly seated on the back of the unit.
3. Ensure the dirty water tank is properly seated on the front of the unit.

Àgbáye Omi Omi mimọ

1. Yọ ojò omi mímọ́ kúrò ní ẹ̀yìn ẹ̀rọ náà.
2. Yọọ fila kuro ni isalẹ ojò naa.
3. Fill the tank with warm tap water up to the 'Water' fill line for the desired cleaning area (small or large).
4. Add the BISSELL Multi-Surface Cleaning Formula up to the corresponding 'Formula' fill line.
5. Replace the cap and reinsert the tank into the machine, ensuring it is securely latched.

Awọn ilana Iṣiṣẹ

Powering On and Selecting Mode

1. Pulọọgi okun agbara sinu iṣan itanna ti ilẹ.
2. Tẹ bọtini agbara ti o wa lori mu lati tan ẹrọ naa.
3. Use the fingertip controls on the handle to select the appropriate cleaning mode: Ipakà lile or Agbegbe Rug.

Ninu Ilana

To dispense cleaning solution, hold down the spray trigger located on the handle. Release the trigger to stop dispensing.

For best results, make a wet pass by holding the spray trigger and moving the machine slowly forward and backward. Then, make a dry pass by releasing the trigger and moving the machine over the same area to suction up the dirty solution.

Image: A user operating the BISSELL CrossWave 17132 on a hard floor, demonstrating its cleaning action on a liquid spill.

Image: The BISSELL CrossWave 17132 cleaning a tiled floor, effectively picking up scattered dry debris and wet messes.

Itọju ati Itọju

Sofo ati Cleaning awọn idọti Omi ojò

1. Pa a ati yọọ ẹrọ naa.
2. Yọ ojò omi idọti kuro ni iwaju ẹrọ naa.
3. Carefully remove the filter and pour out the dirty water.
4. Rinse the tank and filter thoroughly with water. Allow the filter to air dry completely before reinserting.
5. Replace the filter and reattach the dirty water tank to the machine, ensuring it is securely latched.

Cleaning the Brush Roll and Brush Roll Window

1. Pa a ati yọọ ẹrọ naa.
2. Yọ fèrèsé yípo fẹ́lẹ́fẹ́lẹ́ náà kúrò nípa fífà sókè lórí tábìlì náà.
3. Remove the brush roll by grasping the tab and pulling it out.
4. Fi omi tó ń ṣàn fọ fèrèsé náà àti brush roll náà. Yọ gbogbo irun tàbí ìdọ̀tí kúrò.
5. Allow both to air dry completely before reassembling.
6. Reinsert the brush roll, ensuring it clicks into place, then reattach the brush roll window.

Aworan: A sunmọ-soke view of the BISSELL CrossWave 17132's brush roll and base, highlighting the multi-surface brush for effective cleaning.

Using the Storage and Cleaning Tray

After each use, place the CrossWave on the storage and cleaning tray. Fill the tray with water up to the indicated line. Run the machine for approximately 10-20 seconds to rinse the brush roll and internal components. This helps prevent odors and maintains performance.

Laasigbotitusita

Machine Not Dispensing Solution

• Check if the clean water tank is properly filled and seated.
• Ensure the spray trigger is being held down during operation.
• Verify that the formula cap is securely tightened.

Afamora ti ko dara

• Ṣàyẹ̀wò bóyá táǹkì omi tó dọ̀tí kún àti pé ó nílò kí ó gbẹ.
• Rí i dájú pé a gbé ojò omi tó dọ̀tí kalẹ̀ dáadáa, a sì ti dì í.
• Inspect the brush roll and brush roll window for clogs or debris.
• Clean the filter and ensure it is dry before reinstallation.

Ẹrọ Ko Titan

• Verify the power cord is securely plugged into a working electrical outlet.
• Ṣayẹwo fun eyikeyi tripped Circuit breakers.

Awọn pato ọja

Atilẹyin ọja ati Support

For warranty information, technical support, or to purchase replacement parts and cleaning formulas, please visit the official BISSELL website or contact BISSELL customer service. Always use genuine BISSELL replacement parts and cleaning formulas to ensure optimal performance and to maintain your warranty.

Ko si awọn fidio ọja osise lati ọdọ olutaja ti o wa fun ifibọ da lori data ti a pese.