GoControl WS15Z5-1 Z-Wave(R) Wall Switch User Manual

Ọrọ Iṣaaju

Thank you for choosing the GoControl WS15Z5-1 Z-Wave Wall Switch. This smart switch allows you to control your lighting or other connected loads remotely via a Z-Wave network, as well as manually. It integrates seamlessly into your smart home system, providing convenience and energy efficiency. Please read this manual carefully before installation and operation to ensure proper use and safety.

Alaye Aabo

IKILO: Risk of Electric Shock. Installation should be performed by a qualified electrician. Disconnect power at the circuit breaker or fuse box before installation or servicing. Use only copper wire for connections. Do not exceed the maximum load ratings.

• Ensure power is OFF at the circuit breaker before installation.
• Ẹrọ yii jẹ ipinnu fun fifi sori ẹrọ ni ibamu pẹlu koodu ina mọnamọna ti Orilẹ-ede ati awọn ilana agbegbe.
• Do not use in wet locations or where directly exposed to water.
• Fun lilo inu ile nikan.

Package Awọn akoonu

• GoControl WS15Z5-1 Z-Wave Wall Switch
• Awọn skru fifi sori ẹrọ
• Wire Nuts (may vary by package)
• Afowoyi Olumulo (iwe-ipamọ yii)

Eto ati fifi sori

Follow these steps carefully to install your GoControl Z-Wave Wall Switch.

1. Wiring the Switch

1. PA Agbára: Locate the circuit breaker controlling the switch you are replacing and turn it OFF. Verify power is off by attempting to turn on the light or appliance.
2. Yọ Yipada atijọ kuro: Carefully remove the existing wall plate and switch from the wall box. Disconnect the wires from the old switch, noting which wire was connected to which terminal (Line, Load, Neutral, Ground).
3. Ṣe idanimọ Awọn okun:
   • Line (Hot): Usually black, coming from the circuit breaker.
   • Akojọpọ: Usually black, going to the light fixture or appliance.
   • Àdánù: Usually white, often bundled together in the back of the box. (Required for Z-Wave switches).
   • Ilẹ: Usually green or bare copper.
4. So Yipada Tuntun Sopọ: Connect the wires to the GoControl WS15Z5-1 switch terminals as follows:
   • Sopọ awọn Laini wire to the terminal marked "LINE".
   • Sopọ awọn Fifuye wire to the terminal marked "LOAD".
   • Sopọ awọn Àdánù wire to the terminal marked "NEUTRAL".
   • Sopọ awọn Ilẹ wire to the terminal marked "GROUND".

   Ensure all connections are secure. If you are unsure about wiring, consult a qualified electrician.

5. Yipada sori ẹrọ: Fi pẹ̀lẹ́pẹ̀lẹ́ tẹ switi onírin náà sínú àpótí ògiri. Fi àwọn skru tí a pèsè dè é mọ́.
6. Fi Awo Odi sori ẹrọ: Attach the new or existing wall plate.
7. Pada Agbara pada: Tan agbara pada ON ni Circuit fifọ.

olusin 1: Iwaju view of the GoControl WS15Z5-1 Z-Wave Wall Switch.

2. Z-Wave Inclusion (Pairing)

To integrate the switch into your Z-Wave network, you need to "include" it with your Z-Wave controller.

1. Put your Z-Wave controller into Inclusion/Pairing mode. (Refer to your Z-Wave controller's manual for specific instructions).
2. On the GoControl WS15Z5-1 switch, quickly press the top or bottom paddle lẹẹkan. The LED indicator on the switch will blink to confirm inclusion mode.
3. The controller will confirm successful inclusion. The switch's LED will stop blinking and remain solid or turn off, depending on its status.
4. If inclusion fails, refer to the Troubleshooting section or try "Exclusion" first.

Figure 2: The Z-Wave logo, indicating compatibility with Z-Wave networks.

Ṣiṣẹ Yipada

Iṣakoso Afowoyi

• Tẹ awọn oke of the paddle to turn the connected load ON.
• Tẹ awọn isalẹ of the paddle to turn the connected load PAA.

Z-igbi Iṣakoso

Once included in your Z-Wave network, you can control the switch remotely using your Z-Wave controller, hub, or compatible smart home application.

• Use your Z-Wave app or controller interface to toggle the switch ON/OFF.
• The switch supports standard Z-Wave commands for basic on/off functionality.

Figure 3: GoControl products integrate with smart home systems for control via smartphones and other devices.

Figure 4: Diagram illustrating GoControl's integration across various smart home categories like Climate, Lighting, Security, Sensors, and Access.

Itoju

The GoControl WS15Z5-1 Z-Wave Wall Switch requires minimal maintenance.

• Ninu: To clean the switch, wipe it with a soft, damp asọ. Ma ṣe lo abrasive ose tabi epo.
• Awọn imudojuiwọn famuwia: Check the GoControl website or your Z-Wave controller's documentation for information on potential firmware updates.
• Gbogbogbo Itọju: Rii daju pe iyipada naa ko farahan si ọrinrin ti o pọju tabi awọn iwọn otutu to gaju.

Laasigbotitusita

Z-Wave Exclusion (Removing from Network)

If you need to remove the switch from your Z-Wave network, follow these steps:

1. Put your Z-Wave controller into Exclusion mode. (Refer to your Z-Wave controller's manual for specific instructions).
2. On the GoControl WS15Z5-1 switch, quickly press the top or bottom paddle lẹẹkan. The LED indicator will blink to confirm exclusion mode.
3. The controller will confirm successful exclusion. The switch's LED will stop blinking.

Awọn pato

Atilẹyin ọja ati Support

GoControl products are designed for reliability and performance. For warranty information, technical support, or further assistance, please visit the official GoControl webojula tabi kan si wọn onibara iṣẹ Eka.

Webojula: www.gocontrol.com

Olupese: GOCONTROL