Ọrọ Iṣaaju
This manual provides comprehensive instructions for the setup, operation, and maintenance of your Pro-Ject Essential III Beatles Turntable. Please read this manual carefully before using the product to ensure proper function and longevity.
Package Awọn akoonu
Before beginning, please verify that all items listed below are present in your package:
- Ortofon OM10 Phono Cartridge
- 15 V DC Universal Power Supply
- Hinged Acrylic Dust Cover
- Connect It E Audio Cable
- 7" 45 RPM Adaptor
Image: The Pro-Ject Essential III Beatles Turntable, showcasing its unique design and components.
Ṣeto
Follow these steps to set up your turntable for optimal performance:
- Ṣii silẹ: Ni ifarabalẹ yọ gbogbo awọn paati kuro ninu apoti. Ṣe idaduro apoti fun irinna ọjọ iwaju tabi ibi ipamọ.
- Ibi: Place the turntable on a stable, level surface, away from direct sunlight, heat sources, and strong vibrations. Ensure adequate ventilation.
- Fifi sori ẹrọ awo: Gently place the acrylic platter onto the spindle. Ensure it sits flush.
- Fifi sori igbanu: Carefully loop the silicone drive belt around the sub-platter and the motor pulley. Ensure the belt is not twisted.
- Cartridge Alignment (Pre-mounted): The Ortofon OM10 cartridge comes pre-mounted. Verify it is securely attached to the tonearm.
- Tonearm Balance: Adjust the counterweight at the rear of the tonearm until the tonearm floats freely and horizontally. Then, set the tracking force according to the cartridge manufacturer's specifications (typically 1.5g for Ortofon OM10).
- Anti-skating Adjustment: Attach the anti-skating weight to the designated groove on the tonearm support.
- Ideri Ekuru: Attach the hinged acrylic dust cover to the rear hinges of the turntable.
- Awọn isopọ: Connect the Connect It E Audio Cable from the turntable's RCA outputs to your phono preamplifier tabi amplifier's phono input. Connect the 15V DC universal power supply to the turntable and then to a power outlet.
Image: Detail of the motor pulley and belt drive system.
Image: The tonearm and pre-mounted Ortofon OM10 cartridge.
Awọn ilana Iṣiṣẹ
To play a record:
- Agbara Tan: Flip the power switch located on the side of the plinth to the 'On' position. The platter will begin to spin.
- Yan Iyara: The turntable supports 33 1/3 RPM and 45 RPM. To change speed, manually move the drive belt to the appropriate step on the motor pulley. Use the 7" 45 RPM adaptor for singles.
- Àkọsílẹ̀ Ibi: Carefully place your vinyl record onto the platter.
- Apá Gíga: Lo ohun orin gbe lefa lati gbe ohun orin soke.
- Àpótí Ipò: Fi pẹ̀lẹ́pẹ̀lẹ́ gbé ohun orin náà sórí ihò ìbẹ̀rẹ̀ tí a fẹ́ nínú àwo orin náà.
- Apá ìsàlẹ̀: Slowly lower the tonearm using the lift lever. The stylus will descend onto the record, and playback will begin.
- Ipari Sisisẹsẹhin: At the end of the record, use the tonearm lift lever to raise the tonearm, then return it to its rest. Flip the power switch to 'Off'.
Image: Power switch location on the turntable plinth.
Itoju
Regular maintenance ensures the longevity and optimal performance of your turntable:
- Ideri Ekuru: Always use the dust cover when the turntable is not in use to protect it from dust and debris.
- Cleaning the Plinth: Wipe the plinth with a soft, dry, lint-free cloth. Avoid using abrasive cleaners or solvents.
- Ninu Stylus naa: Use a dedicated stylus brush or cleaning fluid to gently clean the stylus before or after each play. Brush from back to front.
- Awọn igbasilẹ mimọ: Keep your records clean using a record brush or a record cleaning machine to prevent dust from accumulating on the stylus.
- Ayẹwo igbanu: Periodically inspect the drive belt for wear or stretching. Replace if necessary.
Laasigbotitusita
If you encounter issues with your turntable, refer to the following common problems and solutions:
| Isoro | Owun to le Fa | Ojutu |
|---|---|---|
| No power / Turntable not spinning | Power cable disconnected; Power outlet faulty; Power switch off. | Check power connections; Try a different outlet; Ensure power switch is 'On'. |
| No sound or very low sound | Ti yan igbewọle ti ko tọ lori amplifier; Cartridge not connected properly; Amplifier volume too low; No phono preamplifier. | Select correct input (Phono); Check cartridge wiring; Increase volume; Ensure a phono preamplifier is used if your amplifier lacks one. |
| Distorted sound / Skipping | Stylus dirty or worn; Tracking force incorrect; Anti-skating incorrect; Record dirty or damaged. | Clean stylus; Re-adjust tracking force and anti-skating; Clean or replace record. |
| Ariwo humming | Ground wire not connected; Interference from other electronics. | Ensure ground wire is connected to amplifier's ground terminal; Move turntable away from other electronics. |
| Speed inconsistency | Drive belt worn or improperly seated; Motor issue. | Check and re-seat drive belt; Replace belt if worn. If problem persists, contact support. |
Awọn pato
| Ẹya ara ẹrọ | Ẹ̀kúnrẹ́rẹ́ |
|---|---|
| Orukọ awoṣe | Essential III Sgt. Pepper |
| Brand | Pro-Ject |
| Awọn iwọn (L x W x H) | 12.99 x 16.54 x 4.41 inches |
| Iwọn Nkan | 11 poun (isunmọ 5 kg) |
| Asopọmọra Technology | RCA |
| Ohun elo | Engineered Wood, Plastic |
| wakọ System | Wakọ igbanu pẹlu mọto amuṣiṣẹpọ ati igbanu silikoni |
| Pẹpẹ | Acrylic (Acryl it E upgrade) |
| Ohun ija | 8.6" Aluminium Tonearm |
| Katiriji | Pre-mounted Ortofon OM10 |
| On-mode Agbara agbara | 4.5 watt |
Atilẹyin ọja ati Support
For warranty information and technical support, please refer to the official Pro-Ject Audio Systems webaaye tabi kan si alagbata ti a fun ni aṣẹ. Jeki ẹri rira rẹ fun awọn iṣeduro atilẹyin ọja.
Olupese: Awọn Ẹrọ Audio Pro-Ject
Akọkọ Wa: Oṣu Karun ọjọ 31, Ọdun 2017
Ilana Pada: 30-day refund/replacement (as per Amazon's policy at time of data retrieval).
Fun iranlọwọ siwaju sii, ṣabẹwo si Pro-Ject Store on Amazon.
