EK EK-M.2 NVMe Aluminum SSD M.2 2280 Heat Sink Instruction Manual

1. Ifihan

The EK EK-M.2 NVMe Aluminum SSD M.2 2280 Heat Sink is designed to provide efficient cooling for your M.2 NVMe Solid State Drive, preventing thermal throttling and ensuring sustained performance. This manual provides detailed instructions for proper installation and usage.

2. Package Awọn akoonu

• EK-M.2 NVMe Aluminum Heat Sink (Top and Bottom Plates)
• Thermal Pads (various thicknesses for optimal contact)
• Mounting Clips/Screws (depending on model variant)
• Small Screwdriver (for installation)

3. Itọsọna fifi sori ẹrọ

Follow these steps carefully to install your EK-M.2 NVMe Aluminum Heat Sink. Ensure your computer or console is powered off and disconnected from the power source before beginning installation.

3.1. Igbaradi

1. Power off your computer or console and disconnect it from the power outlet.
2. Open your computer case or console to access the M.2 slot.
3. If an M.2 SSD is already installed, carefully remove the retaining screw and gently pull the SSD out of the slot.

3.2. Applying Thermal Pads

Thermal pads ensure efficient heat transfer from the SSD components to the heatsink. Select the appropriate thickness of thermal pads based on your SSD's design (single-sided or double-sided).

Image: Components of the EK-M.2 NVMe Aluminum Heat Sink, including the top and bottom plates, thermal pads, and mounting clips.

1. Carefully peel off the protective film from both sides of the thermal pads. Do not remove the thermal pads themselves.
2. Place the thermal pads onto the SSD, ensuring full coverage of the memory chips and controller. For double-sided SSDs, apply pads to both sides.
3. Place the SSD onto the bottom plate of the heatsink, ensuring the thermal pads make good contact.

3.3. Assembling the Heat Sink

1. Align the top plate of the heatsink over the SSD and bottom plate, ensuring the screw holes or mounting points match.
2. Gently press the top plate down to ensure good contact between the thermal pads and the heatsink.
3. Secure the heatsink assembly using the provided clips or screws. If using screws, tighten them diagonally to ensure even pressure.

3.4. Installing the Heatsink-Equipped SSD

Image: The EK-M.2 NVMe Aluminum Heat Sink installed on an M.2 adapter card, ready for insertion into a PCIe slot.

Image: The EK-M.2 NVMe Aluminum Heat Sink installed within a PC case, showing its compact profile near other components.

1. Carefully insert the heatsink-equipped M.2 SSD into the M.2 slot on your motherboard or adapter card. Ensure it is fully seated.
2. Secure the SSD with the retaining screw provided by your motherboard or adapter.
3. Close your computer case or console.
4. Reconnect the power cable and power on your system.

3.5. Post-Installation (PS5 Specific)

1. For PlayStation 5 installations, after physical installation, power on your console.
2. The PS5 will prompt you to format the newly installed M.2 SSD. Follow the on-screen instructions to complete the formatting process.
3. Once formatted, you can adjust the installation location for games and applications in the PS5 settings under Storage.

4. Ṣiṣẹ

Once installed, the EK-M.2 NVMe Aluminum Heat Sink operates passively, continuously dissipating heat from your M.2 SSD. No additional software or configuration is required for its cooling function.

You may use third-party software to monitor your SSD's temperature to confirm optimal cooling performance.

5. Itọju

To ensure long-term performance, periodically inspect the heatsink for dust accumulation. If dust is present, gently clean the fins using compressed air or a soft brush. Ensure your system is powered off and disconnected from power before performing any cleaning.

6. Laasigbotitusita

• High SSD Temperatures:
  • Verify that the thermal pads are correctly applied and making full contact with both the SSD and the heatsink.
  • Ensure the heatsink is securely mounted to the SSD.
  • Check for adequate airflow within your computer case or console. Improve case fan configuration if necessary.
• SSD Not Detected (after heatsink installation):
  • Ensure the SSD is fully seated in the M.2 slot.
  • Check that the retaining screw is not overtightened, which could cause misalignment.
  • For PS5, ensure the drive has been formatted through the console's system settings.

7. Awọn pato

8. Atilẹyin ọja ati Support

This EK product is covered by the manufacturer's standard warranty. For specific warranty terms and conditions, please refer to the documentation included with your purchase or visit the official EK website. For technical support or further assistance, please contact EK customer service.