1. Ifihan
The Sennheiser XSW 1-835 Dual Channel Wireless Microphone System provides reliable, high-quality audio transmission for various applications, including live performances, presentations, and events. This system is designed for ease of use, offering intuitive controls and robust performance. This manual will guide you through the setup, operation, and maintenance of your wireless microphone system.
2. Ohun ti o wa ninu Apoti
Upon unboxing your Sennheiser XSW 1-835 Dual system, please ensure all the following components are present:
- 1x EM-XSW 1 DUAL receiver
- 2x SKM 835-XSW handheld transmitters (dynamic, cardioid)
- 2x MZQ 1 microphone clamps
- 1x NT 12-5 CW power supply
- 2x AA batteries (for transmitters)
Image: All components of the Sennheiser XSW 1-835 Dual Channel Wireless Microphone System, including the receiver, two handheld microphones, and accessories.
3. Eto Itọsọna
3.1 Olugba Loriview
The EM-XSW 1 DUAL receiver is the central unit of your wireless system. Familiarize yourself with its front and rear panels.
Image: Front panel of the receiver showing channel displays, volume controls, scan, and sync buttons for both channels.
The front panel features two independent channel displays, volume controls, and 'SET/SCAN' and 'SYNC' buttons for each channel. These allow for easy frequency scanning and synchronization with the transmitters.
Image: Rear panel of the receiver showing balanced XLR outputs, unbalanced 1/4 inch outputs, Line/Mic switches, SQ (Squelch) controls, and the power input.
The rear panel provides balanced XLR outputs, unbalanced 1/4 inch (6.3mm) jack outputs, Line/Mic level switches, and SQ (Squelch) controls for each channel, along with the DC power input.
3.2 Microphone Overview
The SKM 835-XSW handheld transmitters are equipped with dynamic, cardioid capsules for clear vocal reproduction.
Image: Two handheld microphones, showing the display and power/mute switch.
Each microphone features a display indicating battery status and channel, along with a power/mute switch. The battery compartment is located at the base of the microphone.
3.3 Ibẹrẹ Asopọ
- So agbara: Plug the NT 12-5 CW power supply into the receiver's 'Power' input and then into a wall outlet.
- So Audio: Use XLR cables to connect the 'Balanced' outputs of the receiver to your mixer or amplifier. Alternatively, use 1/4 inch jack cables for the 'Unbalanced' outputs. Ensure the 'Line/Mic' switch on the receiver's rear panel matches the input sensitivity of your connected device.
- Fi Awọn batiri sii: Unscrew the bottom part of each SKM 835-XSW microphone and insert two AA batteries, observing polarity.
3.4 Syncing Microphones
To establish a wireless connection between the receiver and microphones:
- Agbara Lori olugba: Press the power button on the receiver.
- Scan for Frequencies: On the receiver, press the 'SET/SCAN' button for the desired channel. The receiver will automatically scan for an available frequency.
- Prepare Microphone: Power on the SKM 835-XSW microphone.
- Initiate Sync: Hold the microphone's infrared (IR) window close to the receiver's IR window (usually located near the 'SYNC' button). Press the 'SYNC' button on the receiver for the corresponding channel. The receiver will transmit the selected frequency to the microphone.
- Jẹrisi Asopọmọra: Once synchronized, the receiver's display will show the channel number, and the microphone's display will show the matching frequency. The RF signal indicator on the receiver should illuminate.
4. Awọn ilana Iṣiṣẹ
4.1 Titan / Pa a
- Olugba: Tẹ bọtini agbara ni iwaju nronu.
- Gbohungbohun: Slide the power switch on the microphone handle.
4.2 Siṣàtúnṣe iwọn
Use the 'VOL+' and 'VOL-' buttons on the receiver's front panel to adjust the output level for each channel independently. Start with a moderate volume and adjust as needed on your mixer.
4.3 ikanni Yiyan
While the 'SET/SCAN' button automatically finds clear frequencies, you can manually select channels using the 'CH+' and 'CH-' buttons on the receiver. Always re-sync the microphone after changing the receiver channel.
4.4 batiri Management
The microphone display shows the battery status. Replace batteries when the indicator shows low power to avoid interruptions during use. For optimal performance and environmental responsibility, consider using high-quality rechargeable AA batteries.
5. Itọju
- Ninu: Use a soft, dry cloth to clean the receiver and microphones. Do not use liquid cleaners or solvents.
- Ibi ipamọ: Store the system in a cool, dry place away from direct sunlight and extreme temperatures. Remove batteries from microphones if storing for extended periods to prevent leakage.
- Gbohungbohun Grille: Periodically clean the microphone grille to remove debris.
6. Laasigbotitusita
| Isoro | Owun to le Fa | Ojutu |
|---|---|---|
| Ko si ohun lati gbohungbohun | Microphone not powered on, batteries low/dead, microphone not synced, receiver volume too low, mixer input issues. | Ensure microphone is on, replace batteries, re-sync microphone with receiver, increase receiver volume, check mixer connections and input levels. |
| kikọlu / Aimi | Other wireless devices, too far from receiver, obstacles, poor frequency selection. | Perform a frequency scan on the receiver to find a clear channel, ensure line-of-sight to receiver, reduce distance, avoid strong electromagnetic fields. |
| Didara ohun afetigbọ kekere | Incorrect Line/Mic switch setting, microphone too far from sound source, SQ (Squelch) setting too high. | Adjust Line/Mic switch to match mixer input, ensure proper microphone technique, lower SQ setting on receiver. |
| Microphone drops out intermittently | Low battery, range issues, interference. | Replace batteries, reduce distance to receiver, re-scan for a clearer frequency. |
7. Awọn pato
| Ẹya ara ẹrọ | Ẹ̀kúnrẹ́rẹ́ |
|---|---|
| Orukọ awoṣe | XSW 1-835 DUAL |
| Nọmba Awoṣe Nkan | 508270 |
| Brand | Sennheiser |
| Gbohungbo Fọọmù ifosiwewe | Amusowo |
| Pola Àpẹẹrẹ | Alaiṣedeede (Cardioid) |
| Nọmba ti awọn ikanni | 2 |
| Idahun Igbohunsafẹfẹ | 548 - 572 MHz (Band A) |
| Ifamọ Audio | 103 Decibels |
| Ifihan Ibuwọlu-si-Noise | 103 dB |
| Asopọmọra Technology | XLR |
| Orisun agbara | Battery Powered (2 AA batteries per microphone) |
| Iwọn Nkan | 245 Grams (microphone) |
| Ọja Mefa | 16.9 x 13.6 x 3.3 inches (Receiver) |
| Ohun elo | Irin |
| Awọn iwọn otutu ti nṣiṣẹ | 0 ° C si +40 ° C (32 ° F si 104 ° F) |
8. Atilẹyin ọja ati Support
Sennheiser products are built to high-quality standards and come with a manufacturer's warranty. For specific warranty details, please refer to the warranty card included with your product or visit the official Sennheiser webojula.
For technical support, service, or further inquiries, please contact Sennheiser customer service through their official website or the contact information provided in your product packaging. Keep your proof of purchase for warranty claims.